Actuator for exhaust flap OEM part number: 18307851568 (18 30 7 851 568) Suitable for the following BMW models with exhaust flap: F80 F82 F83 F85 F86 F87N F90 F91 F92 F93 F95 F96 F97 F98 G01 G02 G05 G06 G14 G15 G16 G20 G21 G22 G23 G26 G30 G42 G82 G83

Here you get a sports air filter with all its advantages:- higher air flow rate- higher filter performance (even smaller particles are filtered)- The particles are trapped in the filter after intake and thus remain trapped until cleaning.- Washable and reusable filter- Increased air flow and therefore better combustion in the engine- No reduction in air flow over a minimum of 50,000 km- Sufficient air even at high engine speeds- more power- Better intake noise- Reduced fuel consumption These sports air filters have polyurethane as the edge material. Polyurethane is more resistant to petrol, vapours and the like. It has an ideal remoulding. This ensures that the edge of the filter is 100% sealed even when it is reinserted after cleaning. The edge surface is made from a single mould. With many other makes, pores in the edge material and joining surfaces where the edge is joined together often lead to a crack in the edge, which can result in unclean air being sucked into the engine. With paper filters, the air flow rate is significantly lower and decreases further after just a short period of use.In addition, paper filters must be disposed of after the specified mileage. TitanTec sports air filters last a lifetime. This is good for the environment and your wallet.Other washable cotton filters only filter much larger particles compared to TitanTec sports air filters. Cleaning the filters:A TitanTec sports air filter has no oil residue and has 100% of its original performance again after cleaning.Cleaning is quick and easy.We recommend cleaning after 15,000-20,000 kilometres or once a year at the latest.The best time to clean the air filter is around the end of May or beginning of June, i.e. after the pollen count, as this is the time when the air filter is under the most strain.Under no circumstances should aggressive cleaning agents such as petroleum ether, cleaning petrol, brake cleaner etc. be used, as this can damage the material. Details: Type: 2x panel filter Length: 187 mm Width: 235 mm Compatible vehicles: BMW 2 Coupe (G42, G87) M2, 460 hp, 338 kW, from 11/22 BMW 3 (G20, G80, G28) M3, 480 hp, 353 kW, from 11/20 BMW 3 (G20, G80, G28) M3 Competition, 510 hp, 375 kW, from 11/20 BMW 3 (G20, G80, G28) M3 Competition xDrive, 510 hp, 375 kW, from 05/21 BMW 3 (G20, G80, G28) M3 CS xDrive, 551 hp, 405 kW, from 03/23 BMW 3 Touring (G21, G81) M3 Competition xDrive, 510 hp, 375 kW, from 07/22 BMW 4 Coupe (G22, G82) M4, 480 hp, 353 kW, from 11/20 BMW 4 Coupe (G22, G82) M4 Competition, 510 hp, 375 kW, from 11/20 BMW 4 Coupe (G22, G82) M4 Competition M xDrive, 510 hp, 375 kW, from 05/21 BMW 4 Coupe (G22, G82) M4 CSL, 551 hp, 405 kW, 05/22 to 02/23 BMW 4 Convertible (G23, G83) M4 Competition M xDrive, 510 hp, 375 kW, from 07/21

The carbon replacement air intakes Twin Fin for the G8x were developed to match the channel lines of the SP1 G8X front splitter. With both the SP1 and Twin Fin ducts installed, you get the aggressive angles your front end needs.Our covers are a direct replacement, which means you can finally remove the honeycomb grille that is currently in front of the air ducts.These covers are made of pure pre-preg carbon, so the bumper adds minimal weight while providing the aggressive look you've been wanting. Details:- 100% pure pre-preg carbon fiber construction- OEM style fabric- High gloss finish- Fit guarantee- Mounts to the OEM front bumper using the original grille clip positions- with parts certificate according to §19.3 Compatible vehicles:- BMW G80 M3/Competition/CS Sedan (2021+)- BMW G81 M3 Competition Touring (2021+)- BMW G82 M4/Competition/CSL Coupe (2021+)- BMW G83 M4 Competition Convertible (2021+)Note: This is NOT an original BMW product!

The Carbon Performance Twin Fin air intakes for the G8x were developed to give the vehicle a distinctive look. These covers are made of pure pre-preg carbon, so the bumper adds minimal weight while providing the aggressive look you've been wanting. Details:- 100% pure pre-preg carbon fiber construction- OEM style fabric- High gloss finish- Fit guarantee- with parts certificate according to §19.3 Compatible vehicles:- BMW G80 M3/Competition/CS Sedan (2021+)- BMW G81 M3 Competition Touring (2021+)- BMW G82 M4/Competition/CSL Coupe (2021+)- BMW G83 M4 Competition Convertible (2021+)Note: This is NOT an original BMW product!

The Air Intake Set for the G8X models made of carbon fibre gives your vehicle an upscale look. When you buy Pre-Preg carbon fibre, you are investing in a higher quality and more durable material that will outlast other forms of carbon fibre and potentially save you money in the long run. Scope of delivery:- 1x Air Intake Set Details:- 100% carbon fibre construction- High gloss finish- Fit guarantee Compatible vehicles with S58 engine:- BMW G80 M3 (all models)- BMW G81 M3 (all models)- BMW G82 M4 (all models)- BMW G83 M4 (all models) Note: This is NOT an original BMW product!

Add a touch of luxury to the interior of your G8X with this custom-made center armrest in high-quality leather or Alcantara. The red contrast stitching creates a sporty look inspired by motorsport. Fully compatible with the Karbonius center console and easy to install without any modifications. Features: - Available in high-quality leather or Alcantara - Red motorsport-style stitching - Quick installation – no modifications required - Exclusive design for a personalized interior Scope of delivery: - 1x center armrest Compatible vehicles: - BMW G87 M2 - BMW G80 M3 - BMW G81 M3 - BMW G82 M4 - BMW G83 M4 Note: This is NOT an original BMW product!

Facts: - replaces the main catalyst - with 200 cell HJS stainless steel sports catalyst - Euro 6 compatible - with ECE approval* Compatible vehicles:VehicleVehicle typePowerEngine capacityEngineYear of construction BMW 3 Series (F30/F31/F34)335i / xDrive225kW / 306hp2979cm³N55 B30 A11.11 - 07.15 BMW 3 Series (F30/F31/F34)335i / xDrive240kW / 326hp2979cm³N55 B30 A11.11 - 06.13 BMW 3 Series (F30/F31/F34)335i / xDrive250kW / 340hp2979cm³N55 B30 A07.13 - 06.16 BMW 4 Series (F32/F33/F36)435i / xDrive225kW / 306hp2979cm³N55 B30 A07.13 - 02.16 BMW 4 Series (F32/F33/F36)435i / xDrive250kW / 340hp2979cm³N55 B30 A07.13 - 02.16 Note: Depending on the software version, the engine control light may light up. We recommend the purchase of an OFF set module or software customisation. *This downpipe has ECE approval so that it can be used within the scope of the German Road Traffic Licensing Regulations (StVZO) without registration in the vehicle documents.

Facts: - replaces the main catalyst - with 200 cell stainless steel sports catalyst - Euro 6 compatible - for all nonOPF models up to 05/2018 - Optionally with Thermo-Integral insulation (at extra cost) - with ECE approval* Compatible vehicles:VehicleVehicle typePowerEngine capacityEngineYear of construction BMW 3 Series (F30/F31/F34)340i / xDrive240kW / 326hp2979cm³B58 B30 A07.15 - BMW 3 Series (F30/F31/F34)340i / xDrive265kW / 360hp2979cm³B58 B30 A07.15 - BMW 4 Series (F32/F33/F36)440i / xDrive240kW / 326hp2979cm³B58 B30 A03.16 - 05.21 BMW 4 Series (F32/F33/F36)440i / xDrive265kW / 360hp2979cm³B58 B30 A03.16 - 05.21 Note: Depending on the software version, the engine control light may light up. We recommend the purchase of an OFF set module or software customisation. *This downpipe has ECE approval so that it can be used within the scope of the StVZO without registration in the vehicle documents.

Facts: - 4.49“ (114mm) > 3” (76mm), replaces the main catalyst - with 200 cell stainless steel sports catalyst - Euro 6 compatible - for current OPF models - optionally with Thermo-Integral insulation (at extra cost) - with ECE approval* Compatible vehicles:VehicleVehicle typePowerEngine capacityEngineYear of construction BMW 3 Series (F30/F31/F34)340i / xDrive240kW / 326hp2979cm³B58 B30 A07.15 - BMW 3 Series (F30/F31/F34)340i / xDrive265kW / 360hp2979cm³B58 B30 A07.15 - BMW 4 Series (F32/F33/F36)440i / xDrive240kW / 326hp2979cm³B58 B30 A03.16 - 05.21 BMW 4 Series (F32/F33/F36)440i / xDrive265kW / 360hp2979cm³B58 B30 A03.16 - 05.21 Note: Depending on the software version, the engine control light may light up. We recommend the purchase of an OFF set module or software customisation. *This downpipe has ECE approval so that it can be used within the scope of the StVZO without registration in the vehicle documents.

Facts: - 2x 3” (76mm), replaces the main catalyst - with 200 cell stainless steel sports catalyst - Euro 6 compatible - for current OPF models - with Thermo-Integral insulation (for an extra charge) - with ECE approval* Compatible vehicles:VehicleVehicle typePowerCapacityEngineYear of construction BMW 2er (G87)M2338kW / 460hp2993cm³S58 B30 A11.22 - BMW 3 Series (G80)M3353kW / 480hp2993cm³S58 B30 B11.20 - BMW 3 Series (G80/G81)M3 Competition / xDrive375kW / 510hp390kW / 530hp2993cm³S58 B30 A05.21 -07.24 - BMW 3 Series (G80)M3 CS xDrive405kW / 551hp2993cm³S58 B30 A03.23 - BMW 4 Series (G82)M4353kW / 480hp2993cm³S58 B30 B11.20 - BMW 4 Series (G82/G83)M4 Competition / M xDrive375kW / 510hp2993cm³S58 B30 A11.20 - BMW 4 Series (G82)M4 CSL xDrive405kW / 551hp412kW / 560hp2993cm³S58 B30 A05.22 - 02.2311.22 - 02.23 Note: Depending on the software version, the engine control light may light up. We recommend the purchase of an OFF set module or software customisation. *This downpipe has ECE approval so that it can be used within the scope of the German Road Traffic Licensing Regulations (StVZO) without registration in the vehicle documents.

Facts: - 2x 3.15“ (80mm)/ 2.56” (65mm), replaces the main catalyst - with 200 cell HJS stainless steel sports catalyst - Euro 6 compatible - with Thermo-Integral insulation - with ECE approval* Compatible vehicles:VehicleVehicle typePowerEngine capacityEngineYear of construction BMW 3 Series (F80)M3317kW / 431hp2979cm³S55 B30 A03.14 - 10.18 BMW 3 Series (F80)M3 Competition331kW / 450hp2979cm³S55 B30 A03.16 - 10.18 BMW 3 Series (F80)M3 CS338kW / 460hp2979cm³S55 B30 A01.18 - 10.18 BMW 4 Series (F82/F83)M4317kW / 431hp2979cm³S55 B30 A03.14 - 07.20 BMW 4 Series (F82/F83)M4 Competition331kW / 450hp2979cm³S55 B30 A03.16 - 07.20 BMW 4 Series Coupe (F82)M4 CS338kW / 460hp2979cm³S55 B30 A07.17 - 06.19 BMW 4 Series Coupe (F82)M4 GTS368kW / 500hp2979cm³S55 B30 A03.16 - 06.19 Note: Depending on the software version, the engine control light may light up. We recommend the purchase of an OFF set module or software customisation. *This downpipe has ECE approval so that it can be used within the scope of the German Road Traffic Licensing Regulations (StVZO) without registration in the vehicle documents.

Fakten: - 4.49“ (114mm) > 3” (76mm), replaces the main catalyst - with 200 cell stainless steel sports catalyst - Euro 6 compatible - for current OPF models - with Thermo-Integral insulation (for an extra charge) - with ECE approval* Compatible Vehicles:ManufacturerVehicleVehicle typeEngine capacityPowerEngine typeEmission standard BMWM340i xDriveG202998cm³275kW / 374hpB58B30BEuro 6d - OPF BMWM340i xDriveG202998cm³285kW / 387hpB58B30BEuro 6d - OPF BMWM440i xDriveG222998cm³275kW / 374hpB58B30BEuro 6d - OPF BMWM440i xDriveG222998cm³285kW / 387hpB58B30BEuro 6d - OPF Note: Depending on the software version, the engine indicator light may light up. We recommend a software adjustment in this case. *This downpipe has ECE approval so that it can be used within the scope of the StVZO without registration in the vehicle documents.

This article is only a pre-order! The reduced price is only valid for the time of the pre-order, after that the regular price applies. Facts: - Rear silencer variant - Tailpipes: 4x black - Stainless steel 3 inch (76mm) - Electric flaps - Made in Germany (Lake Constance) - with/without ECE approval* Attention: The delivery date of the exhaust system is in January 2026! Scope of delivery: - 1x Aulitzky Exhaust rear silencer - 4x black tailpipes - ECE handout after testing Compatible vehicles:VehicleVehicle typePowerEngine capacityEngineYear of construction BMW 1 Series (F20/F21)M140i / xDrive250kW / 340hp2998cm³B58 B30 A07.16 - 06.19 BMW 2 Series (F22/F23)M240i / xDrive250kW / 340hp2998cm³B58 B30 A09.15 - 06.21 BMW 3 Series (F30/F31)340i / xDrive240kW / 326hp265kW / 360hp2998cm³B58 B30 A07.15 - 10.18 BMW 4 Series (F32/F33)440i / xDrive240kW / 326hp265kW / 326hp2998cm³B58 B30 A03.16 - 07.20 *In conjunction with the ECE flap control (with type approval), this flap exhaust system has ECE approval so that it can be used legally within the scope of the StVZO without registration in the vehicle documents.The use of flap exhaust systems in conjunction with the race flap control (without approval) is not permitted for use on public roads and is only intended for racing purposes!  If you nevertheless install a product without approval in your vehicle and use it within the scope of the StVZO, you are liable to prosecution. Possible consequences that you can expect in this case: Expiry of the operating license according to §19 of the StVZO and a possible resulting immobilization of the vehicle. Other possible consequences, such as a charge of tax evasion, as well as possible investigations by the environmental authorities are at the discretion of the investigators.

Facts: - Tailpipes: 4x100mm black - 3.0 inch stainless steel - MSD removal - Mounting for the original electric flap actuator - Made in Germany (Lake Constance) - with ECE approval* Scope of delivery: - 1x Aulitzky Exhaust exhaust system from OPF - 4x tailpipes 100mm black - ECE handout Compatible vehicles:VehicleVehicle typePower outputDisplacementEngineYear of construction BMW 3 Series (G80)M3353kW / 480PS2993cm³S58 B30 B11.20 - BMW 3 Series (G80/G81)M3 Competition / xDrive375kW / 510PS390kW / 530PS2993cm³S58 B30 A05.21 -07.24 - BMW 3 Series (G80)M3 CS xDrive405kW / 551PS2993cm³S58 B30 A03.23 - BMW 4 Series (G82)M4353kW / 480PS2993cm³S58 B30 B11.20 - BMW 4 Series (G82/G83)M4 Competition / M xDrive375kW / 510PS2993cm³S58 B30 A11.20 - BMW 4 Series (G82)M4 CSL xDrive405kW / 551hp2993cm³S58 B30 A05.22 *The ECE and the combination certificate for the pre-facelift and facelift models are available (includes intake, intercooler, boost pipe kit, downpipe, exhaust system, 670hp Aulitzky App performance increase and 107dB increase in stationary noise). In conjunction with the standard flap control system (with type approval), this flap exhaust system has ECE approval, meaning that it can be used legally within the scope of the German Road Traffic Licensing Regulations (StVZO) without registration in the vehicle documents.

Facts: - Tailpipes: 4x black - 3.0 inch (76mm) stainless steel flap exhaust system from cat/OPF (depending on vehicle) - MSD removal - Mounting for the original electric flap actuator - Exhaust flaps with ceramic bearings - Made in Germany (Lake Constance) - with ECE approval* Scope of delivery: - 1x Aulitzky Exhaust exhaust system ex cat/OPF - 4x black tailpipes - ECE handout Compatible vehicles:VehicleVehicle typePowerEngine capacityEngineYear of construction BMW 3er (F80)M3317kW / 431hp2979cm³S55 B30 A03.14 - 10.18 BMW 3er (F80)M3 Competition331kW / 450hp2979cm³S55 B30 A03.16 - 10.18 BMW 3er (F80)M3 CS338kW / 460hp2979cm³S55 B30 A01.18 - 10.18 BMW 4er (F82/F83)M4317kW / 431hp2979cm³S55 B30 A03.14 - 07.20 BMW 4er (F82/F83)M4 Competition331kW / 450hp2979cm³S55 B30 A03.16 - 07.20 BMW 4er Coupe (F82)M4 CS338kW / 460hp2979cm³S55 B30 A07.17 - 06.19 *Our combination certificate is already available (includes intake, intercooler, boost / charge pipe kit, downpipe, exhaust system, 560hp Aulitzky App performance upgrade and 114dB (non-OPF) or 95dB (OPF) increase in stationary noise). In conjunction with the standard flap control (with type approval), this flap exhaust system has ECE approval so that it can be used legally within the scope of the StVZO without registration in the vehicle documents.

Facts: - Tailpipes 4x black - 3.0 inch stainless steel - MSD removal - electric flaps - Made in Germany (Lake Constance) -  with ECE approval* Scope of delivery: - 1x Aulitzky Exhaust rear silencer - 4x tailpipes black - ECE handout Compatible vehicles: VehicleVehicle typePower outputengine capacityEngineYear of constructionBMW 3er (G20/G21)M340i xDrive275kW / 374PS2998cm³B58 B30 B07.19 -BMW 3er (G20/G21)M340i xDrive285kW / 387PS2998cm³B58 B30 B03.19 -BMW 4er (G22/G23)M440i xDrive275kW / 374PS2998cm³B58 B30 B11.20 -BMW 4er (G22/G23)M440i xDrive285kW / 387PS2998cm³B58 B30 B07.20 - *This exhaust system has ECE approval so that it can be used within the scope of the StVZO without registration in the vehicle documents.

Function:- variable flap control of the original or retrofitted flap exhaust system- controllable via steering wheel buttons Compatible vehicles: VehicleTypePowerEngine capacityEngine typeYear of constructionBMW 3er (F30/F31/F34)340i / xDrive240kW / 326hp2979cm³B58 B30 A07.15 - BMW 3er (F30/F31/F34)340i / xDrive265kW / 360hp2979cm³B58 B30 A07.15 - BMW 4er (F32/F33/F36)440i / xDrive240kW / 326hp2979cm³B58 B30 A03.16 - 05.21 BMW 4er (F32/F33/F36)440i / xDrive265kW / 360hp2979cm³B58 B30 A03.16 - 05.21 Note: This product is NOT StVZO approved and NOT intended for sale within the EU! This item is for show & motorsport purposes only and must not be used/installed on public roads. If the component is installed on/in the vehicle, the operating license expires! The pictures shown are examples.

Function:- variable flap control of the original or retrofitted flap exhaust system- controllable via steering wheel buttons Compatible vehicles: VehicleTypePowerEngine capacityEngine typeYear of constructionBMW 3er (G80)M3353kW / 480hp2993cm³S58 B30 B11.20 -BMW 3er (G80/G81)M3 Competition / xDrive375kW / 510hp2993cm³S58 B30 A05.21 -BMW 4er (G82)M4353kW / 480hp2993cm³S58 B30 B11.20 -BMW 4er (G82/G83)M4 Competition / M xDrive375kW / 510hp2993cm³S58 B30 A05.21 - Note: This product is NOT StVZO approved and NOT intended for sale within the EU! This item is for show & motorsport purposes only and must not be used/installed on public roads. If the component is installed on/in the vehicle, the operating license expires! The pictures shown are examples.

Function: - Variable flap control of the original or retrofitted flap exhaust system - Can be controlled via steering wheel buttons Compatible vehicles:VehicleVehicle typePower outputengine capacityEngineYear of construction BMW 3 Series (F80)M3317kW / 431PS2979ccS55 B30 A03.14 - 10.18 BMW 3 Series (F80)M3 Competition331kW / 450PS2979ccS55 B30 A03.16 - 10.18 BMW 3 Series (F80)M3 CS338kW / 460PS2979ccS55 B30 A01.18 - 10.18 BMW 4 Series (F82/F83)M4317kW / 431hp2979ccS55 B30 A03.14 - 07.20 BMW 4 Series (F82/F83)M4 Competition331kW / 450PS2979ccS55 B30 A03.16 - 07.20 BMW 4 Series Coupe (F82)M4 CS338kW / 460PS2979ccS55 B30 A07.17 - 06.19 BMW 4 Series Coupe (F82)M4 GTS368kW / 500PS2979ccS55 B30 A03.16 - 06.19 Note:This product is NOT approved in the StVZO and is NOT intended for sale within the EU!This article is intended exclusively for show & motorsport purposes and may not be used/installed in public road traffic.If the component is installed on/in the vehicle, the operating licence expires!The pictures shown are examples.

Function:- variable flap control of the original or retrofitted flap exhaust system- controllable via steering wheel buttons Compatible vehicles: VehicleTypePowerEngine capacityEngine typeYear of constructionEU normBMWM340i xDriveG20/G212998cm³275kW / 374hpB58B30BEuro 6d - OPF BMWM340i xDriveG20/G212998cm³285kW / 387hpB58B30BEuro 6d - OPF BMWM440i xDriveG22/G232998cm³275kW / 374hpB58B30BEuro 6d - OPF BMWM440i xDriveG22/G232998cm³275kW / 374hpB58B30BEuro 6d - OPF Note: This product is NOT StVZO approved and NOT intended for sale within the EU! This item is for show & motorsport purposes only and must not be used/installed on public roads. If the component is installed on/in the vehicle, the operating license expires! The pictures shown are examples.

Suitable for: BMW M2 G87 S58 338kW/460hp 2993cm³ BMW M2 G87 S58 353kW/480hp 2993cm³ BMW M3 G80 S58 353kW/480hp 2993cm³ BMW M3 Competition/xDrive G80/G81 S58 375kW/510hp 2993cm³ BMW M3 Competition xDrive G80/G81 S58 390kW/530hp 2993cm³ BMW M3 CS xDrive G80 S58 405kW/551hp 2993cm³ BMW M4 G82 S58 353kW/480hp 2993cm³ BMW M4 Competition/M xDrive G82/G83 S58 375kW/510hp 2993cm³ BMW M4 CSL xDrive G82 S58 405kW/551hp 2993cm³ BMW M4 CSL xDrive G82 S58 412kW/560PS 2993cm³ Optimise the performance and responsiveness of your G8X with our high-quality Boost Pipe Kit for the S58 engine. Developed using advanced CFD simulations for maximum flow optimisation, this kit offers a premium solution for demanding drivers looking for a performance boost. Your benefits:Flow optimised: Each Boost Pipe has been carefully designed using CFD simulations to ensure optimal airflow and improved performance. Highest pressure resistance: The Boost Pipe Kit has undergone rigorous testing and is pressure resistant up to 6 bar to ensure reliable performance even under extreme conditions. High quality materials: Made from high quality aluminium for maximum durability and performance. Precise fit: Each Boost Pipe is customised for a perfect fit and easy installation without the need for additional adjustments. Improved performance: Optimising the airflow not only increases performance but also improves engine response for an exciting riding experience. Scope of delivery:1x aluminium boost pipe1x parts certificate Note:Please note that the product image is for illustrative purposes only and the actual product may differ. With parts certificate (for easy registration according to §19 paragraph 3 of the StVZO).

In order to transport the air precisely to the brake system, a suitable inlet is essential. To ensure that the air let in through the inlet ducts of the front bumper is not randomly swirled around in the wheel arch, we have developed an inlet duct that can be fitted with little effort and directs the air precisely to the brakes - i.e. exactly where it is needed. The covers can optionally be fitted on the outside in front of the ventilation grilles as protection against moisture or similar. Our brake cooling system is plug & play and requires no modifications to the vehicle. Scope of delivery: - 2x intake scoop L+R Compatible vehicles:- BMW M240i (G42)- BMW M340i (G20/G21)- BMW M440i (G22/G23/G26) Attention: Without approval in the area of the StVZO.

The Endless pads are an excellent brake pad for racing and everyday use. The ME22 is the further development of the popular ME20 brake pad. Unlike the MX72 pad, the ME22 has no heat shields.Coefficient of friction 0.36 - 0.42 µOperating temperature 150 - 800 °CSemi-metallic pad For the rear axle. Compatible vehicles:BMW 4-piston BMW (Performance) brake caliper, blue caliper for F-series vehicles, such as M135i M140i F20 F21, M235i M240i F22 F23, 335i 340i F30 F31 F34, 435i 440i F32 F33 F36, M2 F87, M3 F80,M4 F82 F83Alpina models such as the B3Motorsport articles - without STVZO approval.

The Endless pads are an excellent brake pad for racing and everyday use. The ME22 is the further development of the popular ME20 brake pad. In contrast to the MX72 pad, the ME22 has no heat protection plates.Coefficient of friction 0.36 - 0.42 µOperating temperature 150 - 800 °CSemi-metallic pad For the front axle. Compatible vehicles:BMW 4-piston BMW (Performance) brake caliper, blue caliper on F-series vehicles, such as M135i M140i F20 F21, M235i M240i F22 F23, 335i 340i F30 F31 F34, 435i 440i F32 F33 F36, M2 F87, M3 F80,M4 F82 F83Alpina models such as the B3 Motorsport articles - without STVZO approval.

The Endless pads are an excellent brake pad for racing and everyday use. The MX87 is the further development of the MX72 and not only builds up friction with the disc faster, but is also more heat-resistant. Temperature range from 30-700CLow brake disc wearamazing longevity of the padReduction of heat cracksimproved response behaviourCoefficient of friction of 0.38-0.46 By far the greatest speciality, however, is the balancing act between suitability for everyday use and use on trackdays:This means that this rubber is suitable in every situation, whether on long trackdays, or in everyday use.However, if the vehicle is mainly used on the track, we recommend the N39S. For the front axle. Compatible vehicles:BMW 4-piston BMW (Performance) brake caliper, blue caliper on F-series vehicles, such as. M135i M140i F20 F21, M235i M240i F22 F23, 335i 340i F30 F31 F34, 435i 440i F32 F33 F36, M2 F87, M3 F80,M4 F82 F83Alpina models such as the B3Motorsport articles - without STVZO approval.

The Endless pads are an excellent brake pad for everyday road use with sporadic track days. Despite reduced dust and noise emissions, the MX72 impresses with excellent deceleration values even in the high temperature range. In contrast to the ME20 and ME22 pads, the MX72 has heat protection plates.Coefficient of friction 0.37 - 0.47 µOperating temperature 50 - 700 °CSemi-metallic pad For the rear axle. Compatible vehicles:BMW 4-piston BMW (Performance) brake caliper, blue caliper for F-series vehicles, e.g. M135i M140i F20 F21, M235i M240i F22 F23, 335i 340i F30 F31 F34, 435i 440i F32 F33 F36, M2 F87, M3 F80,M4 F82 F83Alpina models such as the B3Motorsport articles - without STVZO approval.

With the AP-Racing Big Brake Kit, we offer a high-performance solution especially for track days and for race track drivers. The friction rings are mounted floating on the high-strength, milled aluminium pots. The advantages of this are, on the one hand, the lower weight and, on the other, the fact that the friction rings can be replaced cost-effectively when they wear out. The AP-Racing calipers are racing calipers without dust boots, which are only recommended for use on the racetrack (regular cleaning of the calipers is necessary in normal road traffic). Details and scope of delivery:- Big Brake Kit for the front/rear axle, consisting of AP Racing calipers and J-Hook brake discs in 378×34mm- AP Racing 6-piston brake caliper- Brake discs 378×34mm, J-Hook- CNC milled brake caliper adapter incl. material certificate- Braided steel brake lines- incl. brake padsAluminium pots and floating mounting Compatible vehicles:- BMW F87 M2 incl. Competition/CS- BMW F8x M3/M4 incl. Competition NOTES:If we do not expressly refer to a parts certificate or general operating licence (ABE) in the product text, this is a motorsport article that is not approved in the German Road Traffic Regulations (StVZO) and therefore the operating licence expires if no registration is made in accordance with § 21 StVO!This brake system can only be registered by us after special tests. Please note that vehicle spare parts should only be installed by a qualified specialist workshop in order to ensure that they function properly and that the vehicle is roadworthy.

MOVIT DDE steel brake system 380x32mm (4 piston calliper) for the rear axle, from 19 inch rims upwardsApplication-focussed development is the cornerstone of this high-performance brake system. The required balance of weight, performance and durability is optimally combined. The uncompromising selection of materials in production results in a highly unique product that fulfils the diverse requirements of extreme automotive applications. The most important features of the MOVIT brake system are- The progressive staggering of the piston diameters, matched to the vehicle, so that precisely parallel contact pressure between the pad and the disc is guaranteed. This enables even wear of the brake pads and ensures even heat transfer and a reduced system temperature.- Very good heat dissipation due to the open design of the brake pad contour.- Calipers manufactured from high-strength, highly tempered aircraft aluminium 7075 with high-quality material properties (stiffer components, more homogeneous structure), hard anodised and coated with a triple layer of paint.- Optimised stability due to the length of the callipers- Larger brake disc diameter and thickness, more cross holes (each pre-cast hole is re-drilled and countersunk, which has a favourable effect on the flow).- The brake discs are thermally tempered.- The optimised DDE ventilation system (double directional evolvent system) of the brake disc has an 80% larger surface area compared to other brake discs, the temperature of the brake disc is significantly reduced and therefore also the wear.- Long service life of the wearing parts, excellent response behaviour, steel flex lines ensure consistent performance.- Optimally matched brake pads ensure fading resistance, a long service life and reduced wear on spare parts Attention: The conversion means that only rims with at least 19 inches can be fitted! The chassis number of the vehicle on which the brakes are fitted is required for the parts certificate. MOVIT sports brake callipers, 4-piston- Milled from high-strength aircraft aluminium 7075- Two-piece- Use of maximum disc size due to long design- Significantly improved rigidity and extended contact surface of the pad- Uniform heat transfer- Reduced system temperature- Low, even pad wear- Progressive piston staggering- Crown system for fixing the brake hose- RAPAD-X system for quick brake pad replacement without removing the caliper from the bracket- Open brake pad track for optimised cooling- Maximum stability- Maximum braking force MOVIT sports brake discs, 380x32mm, 2-piece- Highly efficient DDE cooling system- Perforated for optimum response behaviour even on wet roads- Highest fading resistance- Special alloy for high thermal conductivity MOVIT comfort brake pads- Enlarged friction surface- Lower system temperature- Uniform heat transfer- Longer service life Scope of delivery:2x MOVIT brake caliper (left/right)2x MOVIT brake disc (left/right)2x vehicle-specific brake caliper adapter1x comfort brake pads2x steel flex lines1x handbrake calliper (depending on selected option)1x installation material1x installation instructions and running-in instructions1x parts certificate Compatible vehicles:BMW 2 Series (F87) Coupé M2 272kW / 370PS / 2979cm³ / N55BMW 3 Series (E92) Coupé M3 309kW / 420PS / 3999cm³ / S65BMW 4 Series (F82) Coupé M4 317kW / 431PS / 2979cm³ / S55

MOVIT DDE steel brake system 396x36mm (6 piston calliper) for the front axle, from 20 inch rims upwardsApplication-focussed development is the cornerstone of this high-performance brake system. The required balance of weight, performance and durability is optimally combined. The uncompromising selection of materials in production results in a highly unique product that meets the diverse requirements of extreme automotive applications. The most important features of the MOVIT brake system are- The progressive staggering of the piston diameters, matched to the vehicle, so that precisely parallel contact pressure between the pad and the disc is guaranteed. This enables even wear of the brake pads and ensures even heat transfer and a reduced system temperature.- Very good heat dissipation due to the open design of the brake pad contour.- Calipers manufactured from high-strength, highly tempered aircraft aluminium 7075 with high-quality material properties (stiffer components, more homogeneous structure), hard anodised and coated with a triple layer of paint.- Optimised stability due to the length of the callipers- Larger brake disc diameter and thickness, more cross holes (each pre-cast hole is re-drilled and countersunk, which has a favourable effect on the flow).- The brake discs are thermally tempered.- The optimised DDE ventilation system (double directional evolvent system) of the brake disc has an 80% larger surface area compared to other brake discs, the temperature of the brake disc is significantly reduced and therefore also the wear.- Long service life of the wearing parts, excellent response behaviour, steel flex lines ensure consistent performance.- Optimally matched brake pads ensure fading resistance, a long service life and reduced wear on spare parts Attention: The conversion means that only rims with at least 20 inches can be fitted! The chassis number of the vehicle on which the brakes are fitted is required for the parts certificate. MOVIT sports brake callipers, 6s1, 6-piston- Milled from high-strength aircraft aluminium 7075- Two-piece- Use of maximum disc size due to long design- Significantly improved rigidity and extended contact surface of the pad- Uniform heat transfer- Reduced system temperature- Low, even pad wear- Progressive piston staggering- Crown system for fixing the brake hose- RAPAD-X system for quick brake pad replacement without removing the caliper from the bracket- Open brake pad track for optimised cooling- Maximum stability- Maximum braking force MOVIT sports brake discs, 396x36mm, 2-piece- Highly efficient DDE cooling system- Perforated for optimum response behaviour even on wet roads- Maximum fading resistance- Special alloy for high thermal conductivity MOVIT comfort brake pads, BE-6s1- Enlarged friction surface- Lower system temperature- Uniform heat transfer- Longer service life Scope of delivery:2x MOVIT brake caliper (left/right)2x MOVIT brake disc (left/right)2x vehicle-specific brake caliper adapter1x set of comfort brake pads2x steel flex lines1x assembly material1x installation instructions and running-in instructions1x parts certificate Compatible vehicles:Audi R8 type 420 -2018Audi S6 Type 4FBMW M2 F87BMW M3 E92BMW M4 F82BMW X5 E70Ford Mustang VI 2016- 2.3l EcoboostFord Mustang VI 5.0 V8 GT 2015-Mercedes Benz W906 Sprinter 3t & 3.5t

AutoTecknic carbon fibre front bumper canards are the complete solution to aerodynamically optimise the handling of the front of a car. Made from lightweight and durable carbon graphite composites, AutoTecknic carbon fibre front bumper canards help to increase front downforce at high speeds. The additional downforce stabilises the car's chassis during hard cornering and increases traction for faster lap times. The optical properties of the carbon also give the F80, F82, F83 a more aggressive design. Compatible vehicles:BMW 3 (F30, F80) M3 2014-2018BMW 3 (F30, F80) M3 CS 2018-2018BMW 3 (F30, F80) M3 Competition 2016-2018BMW 4 Convertible (F33, F83) M4 2014-2020BMW 4 Convertible (F33, F83) M4 Competition 2016-2020BMW 4 Coupe (F32, F82) M4 2014-2020BMW 4 Coupe (F32, F82) M4 CS 2017-2019BMW 4 Coupe (F32, F82) M4 Competition 2016-2020BMW 4 Coupe (F32, F82) M4 GTS 2016-2019

The high-quality carbon fibre front canards are a perfect addition to significantly enhance the style of your vehicle. Unlike regular carbon fibre, pre-preg carbon is reinforced to increase strength and durability. It can also be a staggering 70% lighter than other carbon fibre options.Prepreg carbon is far more uniform than other types of carbon, meaning the likelihood of imperfections is drastically reduced. The manufacturing process eliminates unwanted air bubbles and results in a perfectly smooth and high-gloss finish. Details:- 100% pure prepreg carbon fibre construction- OEM-style weave- High gloss finish- Fit guarantee- With parts certificate according to §19.3 Scope of delivery:- 1x Performance carbon canards Compatible vehicles: BMW G80 M3 Limousine (2021+) BMW G80 M3 Competition Limousine (2021+) BMW G81 M3 Touring (2023+) BMW G81 M3 Competition Touring (2023+) BMW G82 M4 Coupe (2021+) BMW G82 M4 Competition Coupé (2021+) BMW G83 M4 Cabrio (2021+) BMW G83 M4 Competition Cabrio (2021+)  Note: This is NOT an original BMW product!

The high-quality carbon fibre front canards are a perfect addition to significantly enhance the style of your vehicle. Unlike regular carbon fibre, pre-preg carbon is reinforced to increase strength and durability. It can also be a staggering 70% lighter than other carbon fibre options.Prepreg carbon is far more uniform than other types of carbon, meaning the likelihood of imperfections is drastically reduced. The manufacturing process eliminates unwanted air bubbles and results in a perfectly smooth and high-gloss finish. Details:- 100% pure prepreg carbon fibre construction- OEM-style weave- High gloss finish- Fit guarantee- With parts certificate according to §19.3 Scope of delivery:- 1x set carbon front canards Compatible vehicles: BMW G80 M3 Limousine (2021+) BMW G80 M3 Competition Limousine (2021+) BMW G81 M3 Touring (2023+) BMW G81 M3 Competition Touring (2023+) BMW G82 M4 Coupe (2021+) BMW G82 M4 Competition Coupé (2021+) BMW G83 M4 Cabrio (2021+) BMW G83 M4 Competition Cabrio (2021+)  Note: This is NOT an original BMW product!

The Centre console cover for the rear seat made of pre-preg carbon fiber perfectly emphasize the style of the vehicle.Details:- 100% pure pre-preg carbon fibre construction- OEM style carbon fibre- High gloss finish- Perfect fit- Registration free Compatible vehicles: - BMW F80 M3 - BMW F82 M4 Coupe - BMW F83 M4 Cabrio - BMW F87 M2 - BMW F87C M2 - BMW G87 M2  Note: This is NOT an original BMW product!

The side centre consoles give your vehicle an upscale look and feel. When you buy Pre-Preg carbon fibre, you are investing in a higher quality and more durable material that will outlast other forms of carbon fibre and potentially save you money in the long run. Details:- 100% carbon fibre construction- High gloss finish- Fit guarantee- registration free Scope of delivery:1x set of centre console side covers (1x right / 1x left) Compatible vehicles:- BMW G87 M2 - BMW G80 M3 incl. Competition Saloon (2021+)- BMW G81 M3 incl. Competition Touring (2023+)- BMW G82 M4 incl. Competition Coupé (2021+)- BMW G83 M4 incl. Competition Convertible (2021+) Note: This is NOT an original BMW product!

Facts: - 3 inch (76cm) Charge Pipe made of T-6061 aluminum in black - incl. mounting rubbers, clamps - replaces the BMW original part with the part number 13718601684 - Plug'n'Play installation - without approval in the area of the StVZO The aluminium charge pipe replaces the factory plastic pipe. In more powerful vehicles, the increased boost pressure can cause the original pipe to burst. In the worst case, this can lead to engine damage due to fragments being sucked in. Compared to the original, the pressure pipe has an enlarged diameter of 76mm (3").This reduces air turbulence and at the same time increases the air flow. This allows the turbocharger to respond more quickly, which increases the maximum possible output. The engine control unit does not need to be retuned. Even at very high charge pressures, there is no risk of bursting with this pressure pipe. The charge pipe also provides a good basis for retrofitting a water-methanol injection system; a connection for the injector is already prepared (thread for water-methanol injection: 1/8" inch, 21/64 fine thread).The charge pipe is fitted as a plug'n'play direct replacement for the standard part. The charge pipe replaces the original part with the following part number: 13718601684 Compatible vehicles:BMW 1' F20 LCI (09/2015 - 08/2018) M140i / xDriveBMW 1' F21 LCI (09/2015 - 08/2018) M140i / xDriveBMW 2' F22 (09/2015 - 06/2017) M240i / xDriveBMW 2' F22 LCI (09/2016 - 08/2018) M240i / xDriveBMW 2' F23 (09/2015 - 06/2017) M240i / xDriveBMW 2' F23 LCI (10/2016 - 08/2018) M240i / xDriveBMW 3' F30 LCI (10/2014 - 09/2018) 340i / xDriveBMW 3' F31 LCI (10/2014 - 08/2018) 340i / xDriveBMW 3' F34 GT LCI (09/2015 - 07/2018) 340i / xDriveBMW 4' F32 (04/2015 - 02/2017) 440i / xDriveBMW 4' F32 LCI (05/2016 - 08/2018) 440i / xDriveBMW 4' F33 (03/2015 - 02/2017) 440i / xDriveBMW 4' F33 LCI (05/2016 - 08/2018) 440i / xDriveBMW 4' F36 Gran Coupé (03/2015 - 02/2017) 440i / xDriveBMW 4' F36 Gran Coupé LCI (05/2016 - 07/2018) 440i / xDriveBMW 5' G30 (10/2015 - 08/2018) 540i / xDriveBMW 5' G31 (03/2016 - 07/2018) 540i / xDriveBMW 5' G38 (02/2016 - 08/2018) 540i / xDriveBMW 6' G32 GT (09/2016 - 07/2018) 640i / xDriveBMW 7' G11 (10/2014 - 07/2018) 740i / xDriveBMW 7' G12 (10/2014 - 08/2018) 740i / xDriveBMW X3 G01 (10/2016 - 09/2018) xDrive M40iBMW X4 G02 (03/2017 - 08/2018) xDrive M40i Attention: Not approved in the area of the StVZO.

Facts: - Charge pipe made of T-6061 aluminium in black - incl. mounting rubbers, clamps - without licence Compatible vehicles:BMW 3 (G20, G28) (2018-) M 340 i xDrive (B58 B30 B) 2998cm³ 374hp (275kW) 2019 -BMW 3 (G20, G28) (2018-) M 340 i xDrive (B58 B30 B) 2998cm³ 387PS (285kW) 2019 -BMW 3 (G20, G28) (2018-) M 340 i Mild-Hybrid xDrive (B58 B30 B, JA1) 2998cm³ 374PS (275kW) 2020 -BMW 3 Touring Van (G21) (2019-) M 340 i xDrive (B58 B30 B) 2998cm³ 374PS (275kW) 2019 -BMW 4 Coupe (G22) (2020-) M 440 i Mild-Hybrid (B58 B30 B, JA1) 2998cm³ 374PS (275kW) 2021 -BMW 4 Gran Coupe (G26) (2021-) M440 i Mild-Hybrid (B58 B30 B) 2998cm³ 374PS (275kW) 2022 -BMW Z4 Roadster (G29) (2018-) M40 i (B58 B30 C) 2998cm³ 340PS (250kW) 2018 - Attention: Not approved in the area of the StVZO.

Suitable for the following models:BMW F87 M2 Competition 302kW/411hpBMW F80 M3 317kW/431hpBMW F80 M3 Competition 331kW/450hpBMW F80 M3 CS 338kW/460hpBMW F82/F83 M4 317kW/431hpBMW F82/F83 M4 Competition 331kW/450hpBMW F82 M4 CS 338kW/460hpBMW F82 M4 GTS 368kW/500hp The Wagner tuning Ø57mm charge pipe kit for the S55 engine. Discover the new Performance Ø57mm Charge Pipe Kit from Wagner Tuning for your S55 engine. Designed to maximize the performance of your vehicle while improving durability, this kit offers a range of advanced features that will give your vehicle a real performance boost. Features:Optimized fluid dynamics:Compared to the OEM Charge Pipes, Wagner Tuning Charge Pipes offer a larger flow diameter and minimize internal cross-sectional changes, resulting in 40% less backpressure. This relieves the turbochargers and improves the response behavior.Robust construction:The charge pipes are made entirely of aluminum and withstand high pressures as well as aging. Unlike OEM products, they do not burst under load.Special powder coating:The Charge Pipes are coated with a special textured powder coating that not only improves corrosion protection, but also ensures an OEM look. Advantages:Maximized performance:The Performance Charge Pipe Kit improves flow dynamics and reduces back pressure, resulting in increased engine performance and responsiveness.Durability:Thanks to the robust aluminum construction and high-quality powder coating, Charge Pipes offer long-term durability and reliability.Easy installation:The kit is easy to install and requires no complex modifications. With the included mounting hardware, installation is a breeze. Scope of delivery:2 aluminum charge air pipes (black coated)2 silicone adapters (black)4 stainless steel hose clamps1 mounting material1 parts certificate With parts certificate (for easy registration according to §19 paragraph 3 of the StVZO).

Facts: Material: Carbon Manufacturer: Eventuri Parts certificate: without Eventuri carbon fibre charge pipes for S55 F8X models Full carbon S55 Chargepipes by Eventuri. Perfect thermal insulation and built for high pressures thanks to one of the most durable and robust materials on the tuning market. The full carbon fibre charge pipes for S55 engines (F-Series) are not only visually stunning, but also a real technical innovation. Compatible vehicles:VehicleTypePowerEngine capacityEngine typeYear of construction BMW 2 Series Coupe (F87)M2 Competition302kW / 411hp2979cm³S55 B30 A06.18 - 06.21 BMW 3 Series (F80)M3317kW / 431hp2979cm³S55 B30 A03.14 - 10.18 BMW 3 Series (F80)M3 Competition331kW / 450hp2979cm³S55 B30 A03.16 - 10.18 BMW 3 Series (F80)M3 CS338kW / 460hp2979cm³S55 B30 A01.18 - 10.18 BMW 4 Series (F82/F83)M4317kW / 431hp2979cm³S55 B30 A03.14 - 07.20 BMW 4 Series (F82/F83)M4 Competition331kW / 450hp2979cm³S55 B30 A03.16 - 07.20 BMW 4 Series Coupe (F82)M4 CS338kW / 460hp2979cm³S55 B30 A07.17 - 06.19 BMW 4 Series Coupe (F82)M4 GTS368kW / 500hp2979cm³S55 B30 A03.16 - 06.19

Facts: - Charge- & Boostpipe aluminium black - incl. mounting rubbers, clamps Compatible vehicles:VehicleVehicle typePowerEngine capacityEngine typeYear of construction BMW 3 Series (F80)M3317kW / 431hp2979cm³S55 B30 A03.14 - 10.18 BMW 3 Series (F80)M3 Competition331kW / 450hp2979cm³S55 B30 A03.16 - 10.18 BMW 3 Series (F80)M3 CS338kW / 460hp2979cm³S55 B30 A01.18 - 10.18 BMW 4 Series (F82/F83)M4317kW / 431hp2979cm³S55 B30 A03.14 - 07.20 BMW 4 Series (F82/F83)M4 Competition331kW / 450hp2979cm³S55 B30 A03.16 - 07.20 BMW 4 Series Coupe (F82)M4 CS338kW / 460hp2979cm³S55 B30 A07.17 - 06.19

The used "Clubsport bar V3" from Bavarian Car Tuning is a high-quality roll bar that was specially developed for the G80/G82. The bar is made of robust and lightweight material that guarantees high strength and rigidity. It is painted in red and blends seamlessly into the interior of your vehicle. The Clubsport bar V3 is easy to install, fits the dimensions of the G80 perfectly and includes an Isofix mount. The rear seat does not need to be removed. The bar can be installed and removed within 10 minutes.With expert opinion Please note that this is a used item, so there may be slight signs of use (see pictures). Nevertheless, it offers a great opportunity to give your vehicle a sporty touch and increase safety at the same time. SPECIAL PRICE - USED (TOP CONDITION)

H&R coilover springs for G8X models With their special set-up, H&R coilover springs provide noticeably more performance in everyday driving without any significant loss of comfort. Details: Lowering VA: 25-35mm Lowering HA: 30-45mm Chassis: for vehicles with electric damper control Approval type: with parts certificate Product advantages: Sporty look and performance Lowering of the vehicle's centre of gravity Linear or progressive suspension characteristics Can be combined with standard or retrofit dampers Optimised driving dynamics Surface protection through powder coating Made in Germany Compatible vehicles: BMW M3 Limo xDrive Competition & M4 Coupé xDrive Competition, 4WD *Type G234M (G80 / G82) *only with adaptive M suspension

Transform your G8X into a high-performance powerhouse with the BlackBoost cooling air intake system. Experience more power, style and driving dynamics with this premium upgrade. In the world of performance modifications, the airbox is one of the most important engine components you should upgrade. The factory airbox is very restrictive in terms of airflow and filter area. Our cooling air intakes are designed and engineered to overcome these factory restrictions and deliver the maximum airflow with the lowest possible temperatures given the space available. The BlackBoost Cold Air Intakes are designed to be flush with the bonnet of the vehicle and ensure a consistent seal with the rubber seals of the airbox, whilst also ensuring a large surface area to work properly. The BlackBoost twin-flow filters are specifically designed to maximise airflow and surface area. The BlackBoost intake kit is a plug-and-play solution that works perfectly without further customisation and requires no additional software tuning. It also works smoothly in combination with turbo upgrades, downpipes, methanol injections etc. to unleash the necessary airflow and utilise the full capacity of the engine for those aiming for 1000+ WHP figures. Scope of delivery:- Powder coated airbox- Filters- BlackBoost CFD developed filter adapter Key Features:- Proven power increase from 8 to 30+ hp on production vehicles- Improved responsiveness across the entire rev range- Optimised airflow and increased volume range compared to standard equipment- Increased surface area of the filter elements- Can support airflow for 1000+ WHP configurations- Larger filter element surface area compared to OEM- Plug-and-play bolt-on installation- No ECU tuning required Compatible vehicles:BMW M2 (G87) 338kW | 460PS | 2993cm³ | S58BMW M2 (G87) 353kW | 480PS | 2993cm³ | S58BMW M3 (G80) 353kW | 480PS | 2993cm³ | S58BMW M3 (G80) Competition 375kW | 510PS | 2993cm³ | S58BMW M3 (G80) Competition 375kW | 510PS | 2993cm³ | S58 | xDriveBMW M3 (G80) Competition 390kW | 530PS | 2993cm³ | S58 | xDriveBMW M3 (G80) CS 405kW | 551PS | 2993cm³ | S58 | xDriveBMW M3 (G81) Competition 375kW | 510PS | 2993cm³ | S58 | xDriveBMW M3 (G81) Competition 390kW | 530PS | 2993cm³ | S58 | xDriveBMW M4 (G82) | 353kW | 480PS | 2993cm³ | S58BMW M4 (G82) Competition | 375kW | 510PS | 2993cm³ | S58BMW M4 (G82) Competition M | 375kW | 510PS | 2993cm³ | S58 | xDriveBMW M4 (G82) CSL | 405kW | 551PS | 2993cm³ | S58 | xDriveBMW M4 (G82) CSL | 412kW | 560PS | 2993cm³ | S58 | xDriveBMW M4 (G83) Competition M | 375kW | 510PS | 2993cm³ | S58 | xDrive

Verwandeln Sie Ihren F8X mit dem BlackBoost Kühllufteinlass-System in ein leistungsstarkes Kraftpaket. Erleben Sie mehr Leistung, Stil und Fahrdynamik mit diesem Premium-Upgrade. In der Welt der Leistungsmodifikationen ist die Airbox eine der wichtigsten Motorkomponenten, die Sie aufrüsten sollten. Die werksseitige Airbox ist in Bezug auf den Luftstrom und die Filterfläche sehr restriktiv. Unsere Kühllufteinlässe wurden entwickelt und konstruiert, um diese werksseitigen Einschränkungen zu überwinden und den maximalen Luftstrom mit den niedrigstmöglichen Temperaturen zu liefern, wenn man die Platzverhältnisse berücksichtigt. Die BlackBoost Cold Air Intakes sind so konzipiert, dass sie mit der Motorhaube des Fahrzeugs abschließen und eine gleichmäßige Abdichtung mit den Gummidichtungen der Airbox gewährleisten, während sie auch eine große Oberfläche gewährleisten, um richtig arbeiten zu können. Die BlackBoost Twin-Flow-Filter wurden speziell für einen maximalen Luftstrom und eine große Oberfläche entwickelt. Das BlackBoost Ansaugkit ist eine Plug-and-Play-Lösung, die ohne weitere Anpassungen perfekt funktioniert und für die kein zusätzliches Softwaretuning erforderlich ist. Es funktioniert auch problemlos in Kombination mit Turbo-Upgrades, Downpipes, Methanol-Einspritzungen etc., um die notwendige Luftströmung zu entfesseln und die volle Kapazität der Maschine nutzen zu können für diejenigen, die 1000+ WHP-Werte anstreben. Lieferumfang: - Pulverbeschichtete Airbox - Filter - BlackBoost CFD entwickelte Filteradapter Wesentliche Merkmale: - Nachgewiesene Leistungssteigerung von 8 bis 30+ PS bei Serienfahrzeugen - Verbessertes Ansprechverhalten über den gesamten Drehzahlbereich - Optimierter Luftstrom und vergrößerter Volumenbereich im Vergleich zur Serienausstattung - Vergrößerte Oberfläche der Filterelemente - Kann den Luftstrom für Konfigurationen mit 1000+ WHP unterstützen - Größere Oberfläche des Filterelements im Vergleich zum OEM - Plug-and-Play Installation zum Anschrauben - Keine ECU-Abstimmung erforderlich Kompatible Fahrzeuge: BMW M2 (F87) Competition BMW M2 (F87) Competition M BMW M3 (F80) BMW M3 (F80) Competition BMW M3 (F80) Competition M BMW M3 (F80) CS BMW M4 (F82) BMW M4 (F82) Competition BMW M4 (F82) Competition M BMW M4 (F82) GTS BMW M4 (F83) Competition M

Revolutionise the performance of your 1 Series/2 Series/3 Series/4 Series (F Series) with our Competition Intercooler Kit EVO 1! Ready to take the performance of your vehicle to a whole new level? Our Competition Intercooler Kit EVO 1 has been specially developed to optimise the first power levels of engines and achieve an impressive increase in performance. Our intercooler has mesh dimensions of 520x210x130 (11,750 cm³) and offers an astonishing 64% larger flow area and an impressive 60% more charge air volume compared to the factory intercooler. Feel the increased power and improved acceleration. Our high performance mesh is characterised by a high quality Tube Fin mesh with internal turbulators. Despite its size, the entire intercooler weighs only 6.6 kg. The end boxes are made of high-quality cast aluminium and have been optimised using flow analyses in the CFD system. Our intercooler minimises the back pressure compared to the standard intercooler and thus ensures optimum performance. All our intercoolers are equipped with an anti-corrosion coating that ensures long-lasting and optimal cooling. Our kit is completely ready to install and allows for easy replacement with the factory intercooler - a true plug-and-play experience. You can continue to use the original charge air hoses. Now with parts certificate for many vehicles to ensure registration and legal safety. Like all our products, the Competition Intercooler Kit EVO 1 is subject to constant quality monitoring to ensure the highest standards. Prepare to conquer the road with your vehicle. Boost your car's performance, acceleration and driving experience with our Competition Intercooler Kit EVO 1. Whether you're on the motorway or tackling twisty roads, this kit will redefine your vehicles performance. Give your BMW more power and improved performance. Experience the power your vehicle deserves! The Competition Intercooler Kit EVO 1 is plug and play suitable for the following vehicles: BMW 114i F20 / F21 75KW/102PS (2012-2015) BMW 116i F20 / F21 100KW/136PS (2011-2015) BMW 116i F20 / F21 80KW/109PS (2015+) BMW 118i F20 / F21 125KW/170PS (2011-2015) BMW 118i F20 / F21 100KW/136PS (2015+) BMW 120i F20 / F21 130KW/177PS (2014-06/2016) * not suitable for B48 engine BMW 125i F20 / F21 160KW/218PS (2012-06/2016) * not suitable for B48 engine BMW M135i(x) F20 / F21 235-240KW/320-326PS (2011-2016) BMW 114d F20 / F21 70KW/95PS (2012+) BMW 116d F20 / F21 85KW/116PS (2011+) BMW 118d(x) F20 / F21 105-110KW/143-150PS (2011+) BMW 120d(x) F20 / F21 135-140KW/184-190PS (2011+) BMW 125d F20 / F21 160-165KW/218-224PS (2012+) BMW 218i F22 / F23 100KW/136PS (2015-2019) BMW 220i F22 / F23 135KW/184PS (2014-06/2016) * not suitable for B48 engine BMW 228i(x) F22 / F23 180KW/245PS (2014-06/2016) BMW M235i(x) F22/F23 240KW/326PS (2014-2016) BMW M2 F87 272KW/370PS (2016-2018) BMW 218d F22 / F23 103-110KW/143-150PS (2014-2019) BMW 220d(x) F22 / F23 135-140KW/184-190PS (20142019) BMW 225d F22 / F23 160-165KW/218-224PS (2014-2019) BMW 316i F30 / F31 / F34 100KW/136PS (2011-2015) BMW 318i F30 / F31 / F34 100KW/136PS (2015+) BMW 320i(x) F30 / F31 / F34 135KW/184PS (2011-2015) * not suitable for B48 engine BMW 328i(x) F30 / F31 / F34 180KW/245PS (2011-2015) BMW 335i(x) F30 / F31 / F34 225KW/306PS (2011-2015) BMW 316d F30 / F31 / F34 85KW/116PS (2012+) BMW 318d(x) F30 / F31 / F34 105KW/143PS (2012+) BMW 320d(x) F30 / F31 / F34 135-140KW/184-190PS (2011+) BMW 325d F30 / F31 / F34 160KW/218PS (2013+) BMW 328(x)d F30 / F31 / F34 135KW/184PS (2013+) BMW 330d(x) F30 / F31 / F34 190KW/258PS (2012+) BMW 335d(x) F30 / F31 / F34 230KW/313PS (2013+) BMW 418i F32 / F33 / F36 100KW/134PS (2016-) BMW 420i(x) F32 / F33 / F36 135KW/184PS (2013-2015) * not suitable for B48 engine BMW 428i(x) F32 / F33 / F36 180KW/245PS (2013-2016) BMW 435i(x) F32 / F33 / F36 225KW/306PS (2013-2016) BMW 418d F32 / F33 / F36 105-110KW/1143-150PS (2014+) BMW 420d(x) F32 / F33 / F36 135-140KW/184-190PS (2013+) BMW 425d F32 / F33 / F36 160-165KW/218-224PS (2014+) BMW 430d(x) F32 / F33 / F36 190KW/258PS (2013+) BMW 435d(x) F32 / F33 / F36 230KW/313PS (2013+) Scope of delivery: 1 charge air cooler 1 mounting material 1 assembly instructions 1 parts certificate

Maximise the performance of your vehicle with our EVO 2 high performance intercooler kit! Your vehicle deserves the best, and our EVO 2 High Performance Intercooler Kit will make sure you get just that. Here's what you can expect: The Wagner Tuning intercooler an amazing 68% larger flow area compared to the factory radiator. This means more fresh air for your engine and a noticeable increase in performance. Our kit offers an astonishing 90% more charge air volume than the standard cooler. This leads to improved combustion and ultimately more power and efficiency. Despite its impressive size, our intercooler weighs just 8.6kg. The end boxes of the cooler are made of cast aluminium and have been optimised with the help of flow analyses in the CFD system. This guarantees optimum air flow and minimises back pressure. Our competition high-performance mesh is a high-quality tube-fin mesh with internal turbulators, which ensures excellent cooling properties. All our intercoolers have an anti-corrosion coating with excellent heat conduction properties to ensure long-lasting and optimal cooling. Our kit is designed for easy installation and is a plug-and-play upgrade. You can continue to use your original charge air hoses, making installation even easier. The EVO 2 kit has been specifically designed to meet the high demands of the vehicle and is ready to take your performance to the next level. We subject all our products to rigorous quality control to ensure they meet the highest standards. Don't miss the chance to boost the performance of your vehicle. Visit our website for more information and to order your kit. The Competition Intercooler Kit EVO 2 is also plug and play suitable for the following vehicles: BMW 114i F20 / F21 75KW/102hp (2012-2015) BMW 116i F20 / F21 100KW/136hp (2011-2015) BMW 116i F20 / F21 80KW/109hp (2015+) BMW 118i F20 / F21 125KW/170hp (2011-2015) BMW 118i F20 / F21 100KW/136hp (2015+) BMW 120i F20 / F21 130KW/177hp (2014-06/2016) * not suitable for B48 engine BMW 125i F20 / F21 160KW/218hp (2012-06/2016) * not suitable for B48 engine BMW M135i(x) F20 / F21 235-240KW/320-326hp (2011-2016) BMW 114d F20 / F21 70KW/95hp (2012+) BMW 116d F20 / F21 85KW/116hp (2011+) BMW 118d(x) F20 / F21 105-110KW/143-150hp (2011+) BMW 120d(x) F20 / F21 135-140KW/184-190hp (2011+) BMW 125d F20 / F21 160-165KW/218-224hp (2012+) BMW 218i F22 / F23 100KW/136hp (2015-2019) BMW 220i F22 / F23 135KW/184hp (2014-06/2016) * not suitable for B48 engine BMW 228i(x) F22 / F23 180KW/245hp (2014-06/2016) BMW M235i(x) F22/F23 240KW/326hp (2014-2016) BMW M2 F87 272KW/370hp (2016-2018) BMW 218d F22 / F23 103-110KW/143-150hp (2014-2019) BMW 220d(x) F22 / F23 135-140KW/184-190hp (20142019) BMW 225d F22 / F23 160-165KW/218-224hp (2014-2019) BMW 316i F30 / F31 / F34 100KW/136hp (2011-2015) BMW 318i F30 / F31 / F34 100KW/136hp (2015+) BMW 320i(x) F30 / F31 / F34 135KW/184hp (2011-2015) * not suitable for B48 engine BMW 328i(x) F30 / F31 / F34 180KW/245hp (2011-2015) BMW 335i(x) F30 / F31 / F34 225KW/306hp (2011-2015) BMW 316d F30 / F31 / F34 85KW/116hp (2012+) BMW 318d(x) F30 / F31 / F34 105KW/143hp (2012+) BMW 320d(x) F30 / F31 / F34 135-140KW/184-190hp (2011+) BMW 325d F30 / F31 / F34 160KW/218hp (2013+) BMW 328(x)d F30 / F31 / F34 135KW/184hp (2013+) BMW 330d(x) F30 / F31 / F34 190KW/258hp (2012+) BMW 335d(x) F30 / F31 / F34 230KW/313hp (2013+) BMW 418i F32 / F33 / F36 100KW/134hp (2016-) BMW 420i(x) F32 / F33 / F36 135KW/184hp (2013-2015) * not suitable for B48 engine BMW 428i(x) F32 / F33 / F36 180KW/245hp (2013-2016) BMW 435i(x) F32 / F33 / F36 225KW/306hp (2013-2016) BMW 418d F32 / F33 / F36 105-110KW/1143-150hp (2014+) BMW 420d(x) F32 / F33 / F36 135-140KW/184-190hp (2013+) BMW 425d F32 / F33 / F36 160-165KW/218-224hp (2014+) BMW 430d(x) F32 / F33 / F36 190KW/258hp (2013+) BMW 435d(x) F32 / F33 / F36 230KW/313hp (2013+) Dimensions original intercooler: 510mmx130mmx110mm A= 7.293cm³ Wagner Tuning intercooler dimensions: 520mm x215mmx145mm / stepped A= 13.840cm³ Scope of delivery: 1 intercooler 1 mounting material 1 assembly instruction Attention: Not approved in the area of the StVZO.

The EVO 3 Competition intercooler kit fits the following vehicles with N55 engine:BMW F30 / F31 / F34 335i 225KW/306hp (2012-2015)BMW F32 / F36 435i 225KW/306hp (2013-2016)*Not suitable for xDrive models. This impressive intercooler sets new standards and was specially developed for the high demands of the large tuning stages. With mesh dimensions of 510mm x 345mm x 180mm (stepped 23.56L), our intercooler offers a 165% larger flow area and a whopping 223% more charge air volume than the original intercooler. The high-quality competition high-performance mesh with internal turbulators ensures optimum cooling performance. Despite its impressive size, the entire intercooler weighs just 13.8 kg, which underlines its efficiency and lightweight construction. The cast aluminium end boxes of the intercooler have been optimized using flow analyses in the CFD system to ensure excellent cooling properties with minimal back pressure. Our EVO 3 kit eliminates the original click connections and increases the connection diameters at the inlet to Ø65mm and at the outlet to Ø76mm. In addition, the kit includes reinforced silicone hoses and an aluminum charge air tube in Ø76mm. The result is unsurpassed cooling performance with a significant increase in power. Our intercoolers are all coated with a high-quality anti-corrosion coating, which not only ensures protection against environmental influences, but also has excellent heat conduction properties. This ensures long-lasting and optimum cooling. Our intercooler kit is supplied complete and is ready to install. Replacement with the standard parts is easy thanks to the modified crossbar supplied. Due to the extreme size of the intercooler, minor adjustments to the radiator support may be required. Our high-performance charge air cooler has been tested under extreme conditions and is pressure-stable up to 6 bar. Each of our products is subject to constant quality monitoring to ensure maximum reliability. This intercooler is the perfect choice for racing and allows your vehicle to set new standards in terms of power and performance. Advantages of the Wagner Tuning intercooler:- improved cooling performance- 165% larger inflow area- 223% more charge air volume- efficient and lightweight (13.8 kg)- flow-optimized- inlet extended to Ø65mm and outlet extended to Ø76mm- Plug & Play Dimensions original intercooler:510mm x 130mm x 110mmV=7.3 litersA=663 cm² Wagner Tuning intercooler dimensions:510mm x 345mm x 180mm [stepped]V=23.56 litersA=1759.5 cm² Scope of delivery:1 intercooler1 Ø76mm charge air pipe1 external air duct2 silicone hoses1 aluminum adapter1 crossbar1 mounting material1 assembly instructionsAttention: Not approved in the area of the StVZO.

Plug and Play suitable for the following models: BMW G80/81 M3 (Competition) 353-375KW/480-510hp from 2021+ BMW G82/G83 M4 (Competition/CSL) 353-405KW/480-550hp from 2021+ Note: only for vehicles with automatic transmission! Now with parts certificate!Optimise the performance and reliability of your S58 with the Wagner Tuning Competition transmission oil cooler kit. This essential kit for all racing enthusiasts offers superior cooling performance and ensures that the oil temperature always remains in the optimum range, even under extreme conditions. Features:Extended cooling surface: The frontal airflow area has been increased by an impressive 81.6%, allowing for significantly more efficient cooling.Larger mesh volume: With a 93.6% larger mesh volume, this transmission oil cooler ensures maximum heat dissipation and keeps the oil temperature stable even under high loads.Optimum performance: Specially developed for performance-enhanced vehicles, this kit guarantees constant and optimum oil cooling to keep the oil pressure stable and extend the service life of the transmission.Easy installation: The plug & play design enables quick and easy installation, so you can have your vehicle up and running in no time at all. Scope of delivery:1x oil cooler (black coated)1x mounting material1x parts certificate Experience the perfect balance between performance and reliability:The Wagner Tuning Competition transmission oil cooler kit is the ideal addition for your S58. Enjoy the benefits of improved cooling and stable performance that impresses even under the most demanding conditions. With parts certificate (for easy registration according to §19 paragraph 3 of the StVZO).

Includes the following services:- Removing and replacing the connecting rod bearings- Check and measure crankshaft journals- Check and adjust the oil pump- Clean all parts- Wheel alignment- Oil & filter change- incl. all parts such as bearings, screws, seals, oil filter and engine oil (10W60)- Entry in the service booklet with BMW serial number stamp- 1 liter oil refillIn addition, and depending on requirements, we can also replace the spark plugs and engine mounts for an additional charge. Please note:This service can only be carried out at our company headquarters!

Crank Hub Fix incl. working time and the following components:- Oil pan gasket- original set of aluminum screws- Valve cover gasket- Camshaft bolts- Chain tensioner sealing ring- Locking cap- Oil filter- Engine oil- incl. Aulitzky crankshaft lock Attention:The Crank Hub Fix is only available from us including installation.Shipping is not offered! Compatible vehicles:VehicleVehicle typePowerEngine capacityEngine typeYear of construction BMW 2er Coupe (F87)M2 Competition302kW / 411hp2979cm³S55 B30 A06.18 - 06.21 BMW 2er Coupe (F87)M2 CS331kW / 450hp2979cm³S55 B30 A11.19 - 06.21 BMW 3er (F80)M3 Competition331kW / 450hp2979cm³S55 B30 A03.16 - 10.18 BMW 4er (F82)M4 Competition331kW / 450hp2979cm³S55 B30 A03.16 - 07.20

Scope of delivery: - Aulitzky tuning crankshaft lock incl. 8 original fastening screws - Fitting instructions Compatible vehicles:VehicleVehicle typePowerEngine capacityEngine typeYear of construction BMW 2er Coupe (F87)M2 Competition302kW / 411hp2979cm³S55 B30 A06.18 - 06.21 BMW 3er (F80)M3317kW / 431hp2979cm³S55 B30 A03.14 - 10.18 BMW 3er (F80)M3 Competition331kW / 450hp2979cm³S55 B30 A03.16 - 10.18 BMW 4er (F82/F83)M4317kW / 431hp2979cm³S55 B30 A03.14 - 07.20 BMW 4er (F82/F83)M4 Competition331kW / 450hp2979cm³S55 B30 A03.16 - 07.20

Your vehicle is missing a data display! We have it - the CANchecked display for the F-series (F21, F22, F23, F30, F31, F32, F33, F80, F82, F83 and F87. Access to all data from the engine:The sensors are queried directly via Can Bus and are displayed on our tried-and-tested MFD28. The display for the E-series comes with a vehicle-specific cover and fits into the interior like an original part. This means that the ventilation through the slots remains intact. Our display emulates a manufacturer tester so that all detailed values are available. We have optimized the protocol to achieve maximum polling speed. Details:- integrates perfectly into the vehicle interior- Up to 128 sensors can be queried- 10 individually configurable views with our DSS - Display Setup Software- ready-made views for a quick start with our display- simply plug and play via our cable set - plug in, done- 4 additional analog inputs for exhaust gas temperature, oil pressure and more- Best readability - optional anti-reflective film included- Query the sensors like manufacturer diagnostic tools Performance meter:Measure your acceleration times in our performance widget - 0-100, 100-200, 0-200 Data jogging:Log all data to the internal SD card. Whether “on-demand” (start at the tap of a finger) or permanently. All data from your last turn is saved. Preset alarms:Preset alerts can be easily activated and customized. For example, receive a large warning message if the exhaust gas temperature is above 900 degrees. 4 additional analog inputs:Additional temperature and/or pressure sensors can be connected for further monitoring options. e.g. exhaust gas temperature or exhaust gas back pressure. An ethanol sensor can be connected to one of the digital inputs. Read out/delete errors:Read out errors from the engine control unit in plain text and also delete them Individual designWhether it's the individual start screen or the selection from a variety of different widgets. Make the display your display! Switch pages with the cruise control button:To make driving safer, we have integrated the cruise control switch here with the company Lightweight-Performance. When cruise control is not active, you can use the up/down button to switch the views in the display. This has the following advantages:- No “searching” for the display while concentrating on the road ahead- Switching even when wearing gloves (on trackdays)- Quick and safe checking of overview pages and then returning to the main viewDriver Dynamics:We have developed a special view for all track drivers who want to further improve their driving style and become a second or two faster:- G-forces (lateral and longitudinal acceleration)- Vehicle speed- Steering angle- accelerator pedal position- Brake pressure This sensor system gives the driver the opportunity to aim for even higher speeds in bends and to hit the braking point even later. Together with the data log in the internal memory, which can be downloaded from the display after a track day, this offers a great opportunity to synchronize the data with a video. Access to all data from the engine control unit:We supply your display with a ready-made TRI file as standard. All sensors that are queried are defined here. Temperatures:Engine water temperature, oil temperature, intake temperature, exhaust temperature, transmission temperature Pressures:Boost pressure, boost pressure target, fuel pressure high pressure pump, exhaust back pressure, low pressure, front brake pressure, rear brake pressure, oil pressure Lambda/mixture:Lambda value target/actual, injection correction, long-term lambda adjustment, total ignition angle, ignition angle per cylinder Other data:RPM, air mass (g/s), vehicle speed, throttle angle, battery voltage, gear, accelerator pedal position, longitudinal and lateral acceleration, steering angle, yaw angle, torque, power, boost pressure control valve activation If values are missing, they can easily be added. It always depends on the engine whether it supports the values, sometimes not all sensors are available. Attention: Not all values are available for all engines! For which engines and models is the display for F-series:The display fits the following vehicles:- 1 Series: F20, F21- 2 Series: F22, F23- 3 Series: F30, F31- 4 Series: F32, F33- M models: F87, F80, F82, F83 (Convertible) We currently support the following engines, unlisted engines can be added on request:- B48- B58- N13- N47- N55- N57- S55 The respective version for RHD (right-hand drive) is also available. The data may vary between the different engines. Read out and delete errors:Swipe down to access the “DTC” (Diagnostic Trouble Codes = fault memory). The display reads the fault memory from the engine. Optionally, you can also delete these directly on the display. Errors for the engine are displayed in plain text so that you can decide for yourself whether you can continue driving. MFD28 Technical data:- Dimensions: 70.3 x 52mm - Hardware: 2.8” TFT screen, touchscreen, MicroSD, MicroUSB- High-quality milled aluminum front frame- Symmetrical display - ideal for rotating it by 90- Views completely freely configurable on the PC with our DSS - Display Setup Software- Up to 64 widgets per display- 64 sensors (Can Bus + internal)- 10 views- 4x analog inputs- Optional external switching flash- Can bus switching- Can Bus protocols: UDS, KWP2000, OBD Supported values:Many customers always ask: “Which values can I query from my control unit”. The answer: “ALL”. Our MFD28 is compatible with ISO 11898-2 and SAE J2284.The control unit manufacturers themselves determine which values are sent via the CAN bus interface. The documentation is important here - possibly even in the form of a DBC file that can be imported directly. You can also access our extensive list of already implemented control units. This can be found in the download area. A total of up to 50 sensors can be queried if the manufacturer supports this.Broadcast data as well as OBD2 queries via Can Bus (11bit/29bit) are implemented. Special protocols such as TP2.0 from VW/Audi and UDS are also available. DSS - Display Setup Software:With our DSS - Display Setup Software, the display can be conveniently configured on the PC. The Can Bus protocol can be customized, you can import DBC files and design the displays with your own widgets.The log viewer downloads log files from the display. These can then be viewed and values can be individually selected and scaled.A built-in Can Bus logger makes it possible to take a close look at the log. This can be used to reverse-engineer unknown Can Buses.

Here we present our display for the M models of the G series. Access to all data from the engine control unit:So ALL. The sensors are queried directly via Can Bus and are displayed on our tried-and-tested MFD32. The display for the G-series comes with a vehicle-specific panel and fits into the interior like an original part. The sensors are queried via the manufacturer-specific Can Bus protocol. We have optimised the protocol to achieve maximum polling speed. Details:- Integrates perfectly into the vehicle interior- Up to 128 sensors can be interrogated- 10 individually configurable views with our DSS - Display Setup Software- ready-made views for a quick start with our display- simply plug and play via our cable set - plug in, done- 4 additional analogue inputs for exhaust gas temperature, oil pressure and more- Ethanol sensor connection directly to the display- Best readability - optional anti-reflective film included- Query the sensors like manufacturer diagnostic tools Performance metre:Measure your acceleration times in our performance widget - 0-100, 100-200, 0-200 Data jogging:Log all data to the internal SD card. Whether "on-demand" (start with a tap) or permanently. All data from your last turn is saved. Preset alarms:Preset alerts can be easily activated and customised. For example, receive a large warning message if the exhaust gas temperature is above 900 degrees. 4 additional analogue inputs:Additional temperature and/or pressure sensors can be connected for further monitoring options, e.g. exhaust gas temperature or exhaust gas back pressure. An ethanol sensor can be connected to one of the digital inputs. Read out/delete errors:Read out errors from the engine control unit in plain text and also delete them Customised designWhether it's the customised start screen or the selection from a variety of different widgets. Make the display your display! Access to all data from the engine control unit:We supply your display with a ready-made TRI file as standard. All sensors that are queried are defined here. Temperatures:Engine water temperature, intake temperature, exhaust temperature, transmission temperature Pressures:Boost pressure, ambient pressure, oil pressure Lambda/mixture:Lambda value target/actual, short-term lambda adjustment, long-term lambda adjustment, MAF, engine load, torque Driver dynamics:Brake pressure, vehicle speed, throttle angle/gas pedal position Other:Engine speed, total ignition angle, gear, battery voltage, ignition angle reduction per cylinder Analogue inputs:Additional sensors can be added here: Oil temperature, petrol pressure, oil pressure, exhaust gas temperature, etc. but also an ethanol sensor (Flex Fuel) If values are missing, they can easily be added. ATTENTION: not every engine offers all values! For which engines and models is the G-series display:The display bezel fits all G-series (G80/G81/G83/G87) left-hand drive (LHD) vehicles that have the ID7 display installed. The pre-assembled bezel does not fit vehicles with the ID8 monitor! A version for right-hand drive vehicles (RHD) is also available. We currently support the following engines, unlisted engines can be added on request:- B48, B57, B58, M54, M57, N13, N20, N47, N52, N54, N55, N57, S55, S58, S63 MFD32 Technical data:- Dimensions: 89 x 60mm - Hardware: 3.2" TFT screen, touchscreen, MicroSD, MicroUSB- Symmetrical display - ideal for rotating it by 90- Views can be freely configured directly on the display or with our DSS - Display Setup Software on the PC- Up to 64 widgets per display- 64 sensors (Can Bus + internal)- 10 views- 4x analogue inputs- 2x speed input- Optional external switching flash- Can bus switching Supported values:Many customers always ask: "Which values can I query from my control unit? The answer: "ALL". Our MFD32 is compatible with ISO 11898-2 and SAE J2284.The control unit manufacturers themselves determine which values are sent via the CAN bus interface. The documentation is important here - possibly even in the form of a DBC file that can be imported directly. You can also access our extensive list of already implemented control units. This can be found in the download area. A total of up to 50 sensors can be queried if the manufacturer supports this.Broadcast data as well as OBD2 queries via Can Bus (11bit/29bit) are implemented. Special protocols such as TP2.0 from VW/Audi and UDS are also available. DSS - Display Setup Software:With our DSS - Display Setup Software, the display can be conveniently configured on the PC. The Can Bus protocol can be customised, you can import DBC files and design the displays with your own widgets.The log viewer downloads log files from the display. These can then be viewed and values can be individually selected and scaled.An in-built Can Bus logger allows you to take a close look at the log. This can be used to reverse-engineer unknown Can Buses.

ATTENTION: THIS DIFFUSER ONLY FITS MODELS UP TO THE FACELIFT AT THE BEGINNING OF 2017! The Vorsteiner carbon diffuser for the F80 and F82 ideally rounds off the rear of the vehicle. The combination of extreme sportiness and pure elegance from Vorsteiner leaves no questions unanswered. In addition to the visual factor, this full carbon rear apron also impresses in terms of lightweight construction, downforce on the rear axle and therefore the aerodynamics of the entire vehicle. In addition, the diffuser has a 4-step clear lacquer coating to protect it from UV rays. Expert opinion: Material certificate Compatible vehicles:BMW 3 (F30, F80) M3 CS 2018-2018BMW 3 (F30, F80) M3 Competition 2016-2018BMW 4 Convertible (F33, F83) M4 Competition 2016-2020BMW 4 Coupe (F32, F82) M4 2014-2020BMW 4 Coupe (F32, F82) M4 CS 2017-2019BMW 4 Coupe (F32, F82) M4 Competition 2016-2020BMW 4 Coupe (F32, F82) M4 GTS 2016-2019

The 3DDesign carbon diffuser is made entirely of carbon fibre and fits both the F80 and the F82. The rear apron combines the elements of sportiness and elegance. In combination with the integrated side trim strips, the fins give the rear of the vehicle a fresh carbon fibre look. In addition, the downforce on the rear axle is increased, thus improving the aerodynamics of the vehicle. A type 2 diffuser from 3DDesign without the side mouldings is also available. Incl. parts certificate Compatible vehicles:BMW 4 Convertible (F33, F83) M4 2014-2020BMW 4 Convertible (F33, F83) M4 Competition 2016-2020BMW 4 Coupe (F32, F82) M4 2014-2020BMW 4 Coupe (F32, F82) M4 CS 2017-2019BMW 4 Coupe (F32, F82) M4 Competition 2016-2020BMW 4 Coupe (F32, F82) M4 GTS 2016-2019

The 3DDesign carbon diffuser type 2 is made entirely of carbon fibre and gives the rear of the F80 or F82 an individual look in no time at all. The combination of sportiness and elegance is particularly impressive across the board. In addition, the downforce on the rear axle is slightly increased, which has a positive effect on the aerodynamics of the vehicle. A Type 1 diffuser from 3DDesign is also available, which differs in that it has an additional fin on the side. Compatible vehicles:BMW 4 Convertible (F33, F83) M4 2014-2020BMW 4 Convertible (F33, F83) M4 Competition 2016-2020BMW 4 Coupe (F32, F82) M4 2014-2020BMW 4 Coupe (F32, F82) M4 CS 2017-2019BMW 4 Coupe (F32, F82) M4 Competition 2016-2020BMW 4 Coupe (F32, F82) M4 GTS 2016-2019

CSF Race F8X - DKG Transmission Oil Cooler Manufactured with CSF's AC condenser technology using a 1-row super high pressure 26mm multi-channel microtube. Dual-pass high performance core with 10 cooling tubes, compared to the OEM single-pass with 6-tube design for the return line. High-density multi-fin fin design.“Drop-in fit” requires no adjustments during installationAll OEM components are reused, including oil line connections, mounting brackets and shroudLab tested to be ~30% more efficient than the OEM coolerThe world's first and only “plug-and-play” improved DCT transmission cooler for the BMW S55 engine in the BMW F8x M3 M4 Compatible vehicles:BMW 3 (F30, F80) M3 2014-2018BMW 3 (F30, F80) M3 CS 2018-2018BMW 3 (F30, F80) M3 Competition 2016-2018BMW 4 Convertible (F33, F83) M4 2014-2020BMW 4 Convertible (F33, F83) M4 Competition 2016-2020BMW 4 Coupe (F32, F82) M4 2014-2020BMW 4 Coupe (F32, F82) M4 CS 2017-2019BMW 4 Coupe (F32, F82) M4 Competition 2016-2020BMW 4 Coupe (F32, F82) M4 GTS 2016-2019

The daytime running lights bring a touch of the racetrack to the front bumper of your vehicle.The price is without installation.These are the complete modules including heat sink. No complex conversion is necessary for installation, the modules can simply be plugged in (Plug&Play). Not approved in the STVZO area. Only suitable for use in motorsport. Compatible vehicles:VehicleTypePowerEngine capacityEngine typeYear of constructionBMW 3 Series (G80)M3353kW / 480hp2993cm³S58 B30 B11.20 -BMW 3 Series (G80/G81)M3 Competition / xDrive375kW / 510hp2993cm³S58 B30 A05.21 -BMW 4 Series (G82)M4353kW / 480hp2993cm³S58 B30 B11.20 -BMW 4 Series (G82/G83)M4 Competition / xDrive375kW / 510hp2993cm³S58 B30 A05.21 -BMW 4 Series (G22/G23)4 Seriesallallall01.21 - Note: This is NOT an original BMW product!

The ECU battery cover made of pre-impregnated carbon fibre gives your engine compartment an elegant touch.By replacing the standard black plastic cover, you can give your vehicle a personalised touch. When you buy Pre-Preg carbon fibre, you are investing in a higher quality and more durable material that will outlast other forms of carbon fibre and potentially save you money in the long run. Installation: Plug&Play Details:- 100% carbon fibre construction- High gloss finish- registration free Compatible vehicles:- BMW G87 M2 models- BMW G80 M3 Sedan models- BMW G81 M3 Touring models- BMW G82 M4 Coupé models- BMW G83 M4 Convertible models Note: This is NOT an original BMW product!

Facts:Material: CarbonManufacturer: EventuriExpert opinion: Material certificate The Eventuri carbon engine cover for the N55 engine also provides a sporty ambience when looking under the hood.Especially in combination with the Eventuri intake, the engine compartment shines in a completely new look.Compatible vehicles:VehicleVehicle typePowerEngine capacityEngine typeYear of construction BMW 1er (F20/F21)M135i / xDrive235kW / 320hp240kW / 326hp2979cm³N55 B30 A12.11 - 02.1503.15 - 06.16 BMW 2er (F22/F23)M235i / xDrive240kW / 326hp2979cm³N55 B30 A10.13 - 06.16 BMW 2er Coupe (F87)M2272kW / 370hp2979cm³N55 B30 A11.15 - 06.18 BMW 3er (F30/F31/F34)335i / xDrive225kW / 306hp240kW / 326hp250kW / 326hp2979cm³N55 B30 A11.11 - 07.1511.11 - 06.1307.13 - 06.16 BMW 4er (F32/F33/F36)435i / xDrive225kW / 306hp250kW / 340hp2979cm³N55 B30 A07.13 - 02.16

Facts: Material: Carbon Manufacturer: Eventuri Expert opinion: Material certificate Compatible vehicles:VehicleVehicle typePowerEngine capacityEngine typeYear of construction BMW 1er (F20/F21)M140i / xDrive250kW / 340hp2998cm³B58 B30 A09.15 - BMW 2er (F22/F23)M240i / xDrive250kW / 340hp2998cm³B58 B30 A09.15 - 06.21 BMW 3er (F30/F31/F34)340i / xDrive240kW / 326hp265kW / 360hp2998cm³B58 B30 A07.15 - 10.18 BMW 4er (F32/F33/F36)440i / xDrive240kW / 326hp265kW / 360hp2998cm³B58 B30 A03.16 - 06.20

Our high-quality engine cover made from pre-preg carbon fibre is a great addition to enhance the style of your vehicle.The carbon fibre engine cover replaces the standard plastic part. When you buy Pre-Preg carbon fibre, you are investing in a higher quality and more durable material that will outlast other forms of carbon fibre and potentially save you money in the long run. Installation: Plug&Play Details:- 100% carbon fibre construction- High gloss finish- Performance style design- Supplied with 3M double-sided adhesive tape already attached- Use rubber adapter from the original engine cover + emblem- registration free Compatible vehicles with S58 engine:- BMW G87 M2 - BMW G80 M3 Sedan (2021+)- BMW G80 M3 Competition Sedan (2021+)- BMW G81 M3 Touring (2023+)- BMW G81 M3 Competition Touring (2023+)- BMW G82 M4 Coupé (2021+)- BMW G82 M4 Competition Coupé (2021+)- BMW G83 M4 Convertible (2021+)- BMW G83 M4 Competition Convertible (2021+) Note: This is NOT an original BMW product!

Facts: Material: Carbon glossy Manufacturer: Eventuri Expert opinion: Material certificate The G80/G82 is one of Munich's flagship cars and deserves an engine bay that looks as good as it performs. Since the OEM cover makes the engine bay look unfinished, we redesigned it to achieve much-needed symmetry and give the engine a more complete aesthetic. Our cover extends over the intercooler and still allows for adequate heat dissipation through additional venting. Made from prepreg carbon fibre, our engine cover is a direct replacement using the OEM brackets. Compatible vehicles:VehicleTypePowerEngine capacityEngine typeYear of constructionBMW 3 Series (G80)M3353kW / 480hp2993cm³S58 B30 B11.20 -BMW 3 Series (G80/G81)M3 Competition / xDrive375kW / 510hp2993cm³S58 B30 A05.21 -BMW 4 Series (G82)M4353kW / 480hp2993cm³S58 B30 B11.20 -BMW 4 Series (G82/G83)M4 Competition / xDrive375kW / 510hp2993cm³S58 B30 A05.21 -

Facts: Material: Carbon Manufacturer: Eventuri The Eventuri carbon engine cover for the F8x models ensures extreme sportiness and above all individuality under the bonnet, especially in combination with the Eventuri intake, which is also available in carbon or Kevlar! Suitable for the BMW S55 engine. Compatible vehicles:VehicleTypePowerEngine capacityEngine typeYear of construction BMW 3 Series (F80)M3317kW / 431hp2979cm³S55 B30 A03.14 - 10.18 BMW 3 Series (F80)M3 Competition331kW / 450hp2979cm³S55 B30 A03.16 - 10.18 BMW 3 Series (F80)M3 CS338kW / 460hp2979cm³S55 B30 A01.18 - 10.18 BMW 4 Series (F82/F83)M4317kW / 431hp2979cm³S55 B30 A03.14 - 07.20 BMW 4 Series (F82/F83)M4 Competition331kW / 450hp2979cm³S55 B30 A03.16 - 07.20 BMW 4 Series Coupe (F82)M4 CS338kW / 460hp2979cm³S55 B30 A07.17 - 06.19 BMW 4 Series Coupe (F82)M4 GTS368kW / 500hp2979cm³S55 B30 A03.16 - 06.19

Our high-quality and large engine cover made of pre-preg carbon fibre is a great addition to enhance the style of your vehicle. The carbon fibre engine cover replaces the standard plastic part. When you buy Pre-Preg carbon fibre, you are investing in a higher quality and more durable material that will outlast other forms of carbon fibre and potentially save you money in the long run. Installation: Plug&Play Details:- 100% carbon fibre construction- High gloss finish- Performance style design- Supplied with 3M double-sided adhesive tape already attached- Use rubber adapter from the original engine cover + emblem- registration free Compatible vehicles with S58 engine:- BMW G87 M2 - BMW G80 M3 Sedan (2021+)- BMW G80 M3 Competition Sedan (2021+)- BMW G81 M3 Touring (2023+)- BMW G81 M3 Competition Touring (2023+)- BMW G82 M4 Coupé (2021+)- BMW G82 M4 Competition Coupé (2021+)- BMW G83 M4 Convertible (2021+)- BMW G83 M4 Competition Convertible (2021+) Note: This is NOT an original BMW product!

The high-quality carbon sill surround covers are an excellent addition to significantly enhance the style of your vehicle. Unlike regular carbon fibre, pre-preg carbon is reinforced to increase strength and durability. It can also be a staggering 70% lighter than other carbon fibre options.Prepreg carbon is far more uniform than other types of carbon, meaning the likelihood of imperfections is drastically reduced. The manufacturing process eliminates unwanted air bubbles and results in a perfectly smooth and high-gloss finish. Details:- 100% pure prepreg carbon fibre construction- OEM-style weave- High gloss finish- Fit guarantee- Registration free Scope of delivery:- 1x carbon Entry sill surround cover Compatible vehicles:BMW G22 4 Series Note: This is NOT an original BMW product!

The high-quality carbon sill surround covers are an excellent addition to significantly enhance the style of your vehicle. Unlike regular carbon fibre, pre-preg carbon is reinforced to increase strength and durability. It can also be a staggering 70% lighter than other carbon fibre options.Prepreg carbon is far more uniform than other types of carbon, meaning the likelihood of imperfections is drastically reduced. The manufacturing process eliminates unwanted air bubbles and results in a perfectly smooth and high-gloss finish. Details:- 100% pure prepreg carbon fibre construction- OEM-style weave- High gloss finish- Fit guarantee- Registration free Scope of delivery:- 1x carbon Entry sill surround cover Compatible vehicles:BMW G82/G83 M4 Note: This is NOT an original BMW product!

Designed and engineered with the OEM standard as the frame, these AutoTecknic dry carbon fibre wing trims are made with 100% dry carbon fibre composite material and fused with abs tabs that result in strong tabs throughout the durable construction for a secure and seamless fit. As an AutoTecknic standard, each trim piece is individually manufactured with precision, resulting in superior paint quality to accentuate any vehicle. The name of dry carbon fibre comes from its manufacturing process. Dry carbon fibre is formed by using a "pre-impregnated" or impregnated piece of carbon material. This piece of carbon is first placed in a mould and then placed in a sealed autoclave to cure properly. This method produces the least amount of waste and forms a lighter version of the carbon than the "wet" method. The autoclave vacuuming process in the production of dry carbon means fewer pinholes and virtually no air pockets in the carbon. Dry carbon is the highest quality version of carbon fibre products produced. Package includes one pair (passenger and driver side) as a direct OEM replacement for wing liners. Note: The emblems shown in the photos are for demonstration purposes only. The emblems are not included in the package. Original emblems can be reused, or new emblems could be purchased through other suppliers. Compatible vehicles:BMW 3 (F30, F80) M3 2014-2018BMW 3 (F30, F80) M3 CS 2018-2018BMW 3 (F30, F80) M3 Competition 2016-2018BMW 4 Convertible (F33, F83) M4 2014-2020BMW 4 Convertible (F33, F83) M4 Competition 2016-2020BMW 4 Coupe (F32, F82) M4 2014-2020BMW 4 Coupe (F32, F82) M4 CS 2017-2019BMW 4 Coupe (F32, F82) M4 Competition 2016-2020BMW 4 Coupe (F32, F82) M4 GTS 2016-2019

The 3DDesign carbon front bumper spoiler for F82 not only sets new standards visually. The complete bumper is made of carbon fiber and can be painted as desired. Several design variants are already shown in the photos. Visually, this version by specialist is unique. In terms of weight, this full carbon front end is also unrivaled. Compatible vehicles:BMW 4 Convertible (F33, F83) M4 2014-2020BMW 4 Convertible (F33, F83) M4 Competition 2016-2020BMW 4 Coupe (F32, F82) M4 2014-2020BMW 4 Coupe (F32, F82) M4 CS 2017-2019BMW 4 Coupe (F32, F82) M4 Competition 2016-2020BMW 4 Coupe (F32, F82) M4 GTS 2016-2019

The Front Coolant Support Brace made of pre-preg carbon fiber perfectly emphasize the style of the vehicle.Details:- 100% pure pre-preg carbon fibre construction- OEM style carbon fibre- High gloss finish- Perfect fit- Registration free Compatible vehicles:- BMW F-Series Note: This is NOT an original BMW product!

Enhance the aesthetics of the front of your G8X with this carbon fibre front grille. Made from state-of-the-art pre-preg carbon fibre, this grille enhances the aggressive character of the G8X, making your vehicle stand out both on the road and on social media.The road presence this grille offers is unrivalled. You will be amazed by the transformation.The original logo is not included. You can continue to use your old emblem or purchase a new one separately. Details:- 100% pure pre-preg carbon fibre construction- OEM-style fabric- High-gloss surface- Fit guarantee- Fits the OEM grille clip positions- With parts certificate according to §19.3 Compatible vehicles:- BMW G80 M3/Competition Sedan (2021+)- BMW G81 M3 Competition Touring (2021+)- BMW G82 M4/Competition Coupe (2021+)- BMW G83 M4 Competition Convertible (2021+)Note: This is NOT an original BMW product!

The carbon front intakes are an absolute highlight for your vehicle and give it an even sportier look.Key features:- 100% pure prepreg carbon fibre- OEM style weave- High gloss finish- Fitment guarantee- 1 year warranty - With parts certificate according to §19.3 Scope of delivery:1x front spoiler made of glossy prepreg carbon fiber incl. mounting material Compatible vehicles:BMW G80 M3 SedanBMW G81 M3 TouringBMW G82 M4 CoupeBMW G83 M4 Convertible Note: This is NOT an original BMW product!

The Vorsteiner carbon front lip for the F80 and F82 leaves no questions unanswered. Visually, the mixture of extreme sportiness and pure elegance is particularly impressive! The front lip is made entirely of carbon fibre and additionally coated with a 4-stage clear coat to protect it from UV rays. Expertise: Material certificate Compatible vehicles:BMW 3 (F30, F80) M3 CS 2018-2018BMW 3 (F30, F80) M3 Competition 2016-2018BMW 4 Convertible (F33, F83) M4 Competition 2016-2020BMW 4 Coupe (F32, F82) M4 2014-2020BMW 4 Coupe (F32, F82) M4 CS 2017-2019BMW 4 Coupe (F32, F82) M4 Competition 2016-2020BMW 4 Coupe (F32, F82) M4 GTS 2016-2019

The 3DDesign carbon front lip for the F80 and F82 is made entirely of carbon fiber and thus easily meets lightweight construction requirements. Visually, the lip blends in perfectly with the sporty front of the vehicle. In addition, the front lip has a positive effect on the aerodynamic properties of the vehicle. Incl. parts certificate Compatible vehicles:BMW 3 (F30, F80) M3 2014-2018BMW 3 (F30, F80) M3 CS 2018-2018BMW 3 (F30, F80) M3 Competition 2016-2018BMW 4 Convertible (F33, F83) M4 2014-2020BMW 4 Convertible (F33, F83) M4 Competition 2016-2020BMW 4 Coupe (F32, F82) M4 2014-2020BMW 4 Coupe (F32, F82) M4 CS 2017-2019BMW 4 Coupe (F32, F82) M4 Competition 2016-2020BMW 4 Coupe (F32, F82) M4 GTS 2016-2019

Carbon competition front aero lip for the BMW F80, F82 and F83. Manufactured from 100% genuine 3K twill carbon fibre (2X2), this lip is then finished with a multi-coating of high-gloss, UV-resistant clear lacquer. In line with the weight-saving principles of motorsport, we manufacture this lip using a vacuum moulding process with superior strength and accuracy of fit. The lip only weighs a whopping 1.02 kg! The AutoTecknic Carbon Competition Front Aero Lip not only improves the aerodynamic functionality of the vehicle, but also enhances the aesthetics at the front of your vehicle. Compatible vehicles:BMW 3 (F30, F80) M3 2014-2018BMW 3 (F30, F80) M3 CS 2018-2018BMW 3 (F30, F80) M3 Competition 2016-2018BMW 4 Convertible (F33, F83) M4 2014-2020BMW 4 Convertible (F33, F83) M4 Competition 2016-2020BMW 4 Coupe (F32, F82) M4 2014-2020BMW 4 Coupe (F32, F82) M4 CS 2017-2019BMW 4 Coupe (F32, F82) M4 Competition 2016-2020BMW 4 Coupe (F32, F82) M4 GTS 2016-2019

The carbon front lip in DK style for G8X models provides that certain something and impresses with its sporty look.Parts certificate in preparation Compatible vehicles:BMW 3 (G80) M3 BMW 3 (G80) M3 Competiton BMW 3 (G80) M3 CS BMW 3 Touring (G81) M3 CompetitonBMW 4 (G82) M4 BMW 4 (G82) M4 Competiton BMW 4 (G82) M4 CSL BMW 4 Convertible (G83) M4 Competiton MNote: This is NOT an original BMW product!

To increase strength and durability, prepreg carbon fibre is reinforced in contrast to normal carbon fibre and can still be 70% lighter than other carbon options. A decisive advantage in terms of weight saving. Prepreg carbon fibre is far more consistent in quality, so the likelihood of imperfections is greatly reduced. The manufacturing process eliminates unwanted air bubbles and results in a perfectly smooth and high-gloss finish. Key features:- 100% pure prepreg carbon fibre- OEM style weave- High gloss finish- Fitment guarantee- 1 year warranty - With parts certificate according to §19.3 Scope of delivery:1x front spoiler made of glossy prepreg carbon fiber incl. mounting material Compatible vehicles:BMW G80 M3 Sedan (2021+)BMW G80 M3 Competition Saloon (2021+)BMW G81 M3 Touring (2023+)BMW G81 M3 Competition Touring (2023+)BMW G82 M4 Coupe (2021+)BMW G82 M4 Competition Coupe (2021+)BMW G83 M4 Convertible (2021+)BMW G83 M4 Competition Convertible (2021+) Note: This is NOT an original BMW product!

To increase strength and durability, prepreg carbon fibre is reinforced in contrast to normal carbon fibre and can still be 70% lighter than other carbon options. A decisive advantage in terms of weight saving. Prepreg carbon fibre is far more consistent in quality, so the likelihood of imperfections is greatly reduced. The manufacturing process eliminates unwanted air bubbles and results in a perfectly smooth and high-gloss finish. Key features:- 100% pure prepreg carbon fibre- OEM style weave- High gloss finish- Fitment guarantee- 1 year warranty - With parts certificate according to §19.3 Scope of delivery:1x CS front spoiler made of glossy prepreg carbon fiber incl. mounting material Compatible vehicles:BMW G80 M3 Sedan (2021+)BMW G80 M3 Competition Saloon (2021+)BMW G81 M3 Touring (2023+)BMW G81 M3 Competition Touring (2023+)BMW G82 M4 Coupe (2021+)BMW G82 M4 Competition Coupe (2021+)BMW G83 M4 Convertible (2021+)BMW G83 M4 Competition Convertible (2021+) Note: This is NOT an original BMW product!

To increase strength and durability, prepreg carbon fibre is reinforced in contrast to normal carbon fibre and can still be 70% lighter than other carbon options. A decisive advantage in terms of weight saving. Prepreg carbon fibre is far more consistent in quality, so the likelihood of imperfections is greatly reduced. The manufacturing process eliminates unwanted air bubbles and results in a perfectly smooth and high-gloss finish. Key features:- 100% pure prepreg carbon fibre- OEM style weave- High gloss finish- Fitment guarantee- 1 year warranty - With parts certificate according to §19.3 Scope of delivery:1x performance front splitter made of glossy prepreg carbon fiber incl. mounting material Compatible vehicles:BMW G80 M3 Sedan (2021+)BMW G80 M3 Competition Sedan (2021+)BMW G81 M3 Touring (2023+)BMW G81 M3 Competition Touring (2023+)BMW G82 M4 Coupe (2021+)BMW G82 M4 Competition Coupe (2021+)BMW G83 M4 Convertible (2021+)BMW G83 M4 Competition Convertible (2021+) Note: This is NOT an original BMW product!

To increase strength and durability, prepreg carbon fibre is reinforced in contrast to normal carbon fibre and can still be 70% lighter than other carbon options. A decisive advantage in terms of weight saving. Prepreg carbon fibre is far more consistent in quality, so the likelihood of imperfections is greatly reduced. The manufacturing process eliminates unwanted air bubbles and results in a perfectly smooth and high-gloss finish. Key features:- 100% pure prepreg carbon fibre- OEM style weave- High gloss finish- Fitment guarantee- 1 year warranty - With parts certificate according to §19.3 Scope of delivery:1x SOOQOO front splitter made of glossy prepreg carbon fiber Compatible vehicles:BMW G80 M3 SedanBMW G81 M3 TouringBMW G82 M4 CoupeBMW G83 M4 Convertible Note: This is NOT an original BMW product!

To increase strength and durability, prepreg carbon fibre is reinforced in contrast to normal carbon fibre and can still be 70% lighter than other carbon options.A decisive advantage in terms of weight saving. Prepreg carbon fibre is far more consistent in quality, so the likelihood of imperfections is greatly reduced. The manufacturing process eliminates unwanted air bubbles and results in a perfectly smooth and high-gloss finish. Key features:- 100% pure prepreg carbon fibre- OEM style weave- High gloss finish- Fitment guarantee- 1 year warranty- Registration according to §21 possible Scope of delivery:1x SP1 front splitter in prepreg carbon fibre Compatible vehicles:BMW G80 M3 Sedan (2021+)BMW G80 M3 Competition Saloon (2021+)BMW G81 M3 Touring (2023+)BMW G81 M3 Competition Touring (2023+)BMW G82 M4 Coupe (2021+)BMW G82 M4 Competition Coupe (2021+)BMW G83 M4 Convertible (2021+)BMW G83 M4 Competition Convertible (2021+) Note: This is NOT an original BMW product!

To increase strength and durability, prepreg carbon fibre is reinforced in contrast to normal carbon fibre and can still be 70% lighter than other carbon options.A decisive advantage in terms of weight saving. Prepreg carbon fibre is far more consistent in quality, so the likelihood of imperfections is greatly reduced. The manufacturing process eliminates unwanted air bubbles and results in a perfectly smooth and high-gloss finish. Key features:- 100% pure prepreg carbon fibre- OEM style weave- High gloss finish- Fitment guarantee- 1 year warranty- Registration according to §21 possible Scope of delivery:1x front splitter in prepreg carbon fibre Compatible vehicles:BMW G80 M3 Sedan (2021+)BMW G80 M3 Competition Saloon (2021+)BMW G81 M3 Touring (2023+)BMW G81 M3 Competition Touring (2023+)BMW G82 M4 Coupe (2021+)BMW G82 M4 Competition Coupe (2021+)BMW G83 M4 Convertible (2021+)BMW G83 M4 Competition Convertible (2021+) Note: This is NOT an original BMW product!

The carbon front spoilers are an absolute highlight for your vehicle and give it an even sportier look.Key features:- 100% pure prepreg carbon fibre- OEM style weave- High gloss finish- Fitment guarantee- 1 year warranty - Registration possible in accordance with §21 Scope of delivery:1x front spoiler made of glossy prepreg carbon fiber Compatible vehicles:BMW G80 M3/Competition SedanBMW G81 M3/Competition TouringBMW G82 M4/Competition CoupeBMW G83 M4/Competition Convertible Note: This is NOT an original BMW product!

Suitable for the following models:BMW F87 M2 Competition 302kW/411hpBMW F80 M3 317kW/431hpBMW F80 M3 Competition 331kW/450hpBMW F80 M3 CS 338kW/460hpBMW F82/F83 M4 317kW/431hpBMW F82/F83 M4 Competition 331kW/450hpBMW F82 M4 CS 338kW/460hpBMW F82 M4 GTS 368kW/500hp With parts certificate! The 3.0 liter S55B30 turbo engine is equipped with an indirect charge air cooling circuit. This means that the charge air is not cooled using the ambient air as a cooling medium (as usual), but with the aid of a separate cooling water circuit. A reduction in the cooling water temperature can therefore be directly equated with an improved cooling performance of the charge air. This is precisely where the advantages of the WAGNERTUNING upgrade water coolers come into play. The newly developed competition racing nets of the WAGNERTUNING high-performance water coolers increase the radiator volume of the standard water cooler by 89% for the front and 94% for the side. The ratio between the inner and outer cooling surface generates maximum heat transfer and at the same time allows the adjacent components (e.g. the engine water cooler located behind it) sufficient air flow for heat exchange. Furthermore, the increased cooling water volume allows the entire system thermal to be kept at a lower level over a longer period of time. All WAGNERTUNING water coolers are equipped with a thermally conductive anti-corrosion coating to ensure a long-lasting cooling effect. The installation of the system is also uncomplicated and plug & play with the help of our installation instructions. Dimensions OEM water cooler (frontal):590 mm x 308 mm x 25 mmV = 4.5 litersA = 1817 cm² WT water cooler dimensions (frontal):568 mm x 468.4 mm x 32 mmV = 8.5 liters (+89%)A = 2660.5 cm² (+46.4%) Scope of delivery:1x frontal water cooler (low-temperature circuit)1x installation instructions1x parts certificate With parts certificate (for easy registration according to §19 paragraph 3 of the StVZO).

The fuel cap made of pre-preg carbon fiber emphasizes the style of the vehicle perfectly.Details:- 100% pure pre-preg carbon fibre construction- OEM style carbon fibre- High gloss finish- Perfect fit- registration-free Compatible vehicles:- BMW M2 F87 - BMW M2 G87 - BMW M3 E92 - BMW M3 F80 - BMW M3 G80 - BMW M3 G81 - BMW M4 F82 - BMW M4 F83 - BMW M4 G82 - BMW M4 G83 Note: This is NOT an original BMW product!

The gear knob cover gives your vehicle an upscale look and a pleasant feel. When you buy Pre-Preg carbon fibre, you are investing in a higher quality and more durable material that will outlast other forms of carbon fibre and potentially save you money in the long run.Details:- 100% carbon fibre construction- High gloss finish- Fit guarantee- registration free Compatible vehicles:- BMW G87 M2 - BMW G80 M3 incl. Competition Saloon (2021+)- BMW G81 M3 incl. Competition Touring (2023+)- BMW G82 M4 incl. Competition Coupé (2021+)- BMW G83 M4 incl. Competition Convertible (2021+) Note: This is NOT an original BMW product!

Immerse yourself in the world of carbon fibre with our stylish radiator grille upgrade for the G80/81/82/83. Made from high-quality TNF+ dry carbon fibre, it adds a touch of luxury and racing to your vehicle. Installation is child's play - even when fitted. Simply remove the adhesive strips and insert the cover into the side of the grille - and your boring plastic or polystyrene cover is history! Why should you choose prepreg carbon fibre? Unlike conventional carbon fibre, prepreg carbon fibre has additional reinforcement that maximises strength and durability. It is up to 70% lighter than other carbon fibre options, which not only improves performance but also reduces the weight of your vehicle. Our carbon products have a flawless surface finish. Thanks to the manufacturing process without unwanted air bubbles, you get a perfectly smooth and shiny finish that enhances your vehicle and gives it the finishing touch. Treat yourself to the upgrade! Replace your ordinary plastic shell with a classy carbon fibre shell and make your vehicle an eye-catcher on the road. - Made from high-quality prepreg carbon fibre- High-gloss finish for the ultimate shine Scope of delivery:A high quality full carbon fibre cover (Dry Carbon in OEM fabric) to give your vehicle that extra kick. Treat yourself to the difference today! Details:- 100% carbon fibre construction- High-gloss finish- Fit guarantee- registration free Compatible vehicles:- BMW G80 M3 (all models)- BMW G81 M3- BMW G82 M4- BMW G83 M4Note: This is NOT an original BMW product!

Indirect charge air cooling is used in the S55 engine. With indirect charge air cooling, the charge air is cooled by a low-temperature coolant circuit. The low-temperature coolant circuit is then cooled again by the drive air via two air-coolant heat exchangers. A reduced cooling water temperature directly improves the cooling performance of the intercooler. The CSF heat exchanger is installed as an upgrade to the original main heat exchanger and is the largest "drop-in-fit" heat exchanger available on the market for the S55 engine. The CSF heat exchanger has a massive 2-row 42 mm double core with 2x 45 rows and CSF's exclusive B-Tube technology. The B-Tube technology alone enables an increase in cooling efficiency of over 15% compared to the traditional O-tube design of the original heat exchanger. As an OEM supplier with state-of-the-art production machinery, CSF is able to install an extremely efficient fin height of only 6.5 mm for maximum surface contact. The dual-pass flow structure allows the coolant to flow through the core of the radiator twice before exiting the radiator for the lowest possible outlet temperature. The frontal cooling surface increases by ~ 27% compared to the original heat exchanger. Equipped with CNC machined "Quick-Connect" inlet/outlet connections as well as CNC machined brackets and fittings, the CSF heat exchanger is a direct replacement for the original radiator. It can be connected directly and easily to all original hoses, and no grilles, covers or other parts need to be cut or modified - making it a 1:1 replacement. Also ideal as a replacement for accident vehicles or vehicles with a defect. (Please note that various modifications to the plastic parts are required to fit the larger, 50-row Race heat exchanger). In addition, the CSF heat exchanger is equipped with a practical drain plug, which the original system does not have! A stone guard is also included in the scope of delivery. This ensures the greatest possible protection against stone chips in the radiator network. Thanks to thermodynamically optimised anti-corrosion vapour deposition, CSF guarantees maximum quality and durability - this is underlined by the lifetime product guarantee. The radiator is available as "polished chrome" or in a plain black colour. Compatible vehicles:BMW 2 Coupe (F22, F87) M2 CS 2019-2021BMW 2 Coupe (F22, F87) M2 Competition 2018-2021BMW 3 (F30, F80) M3 2014-2018BMW 3 (F30, F80) M3 CS 2018-2018BMW 3 (F30, F80) M3 Competition 2016-2018BMW 4 Convertible (F33, F83) M4 2014-2020BMW 4 Convertible (F33, F83) M4 Competition 2016-2020BMW 4 Coupe (F32, F82) M4 2014-2020BMW 4 Coupe (F32, F82) M4 CS 2017-2019BMW 4 Coupe (F32, F82) M4 Competition 2016-2020BMW 4 Coupe (F32, F82) M4 GTS 2016-2019

The X-Style hood scoops in Pre-Preg carbon fiber are a great addition to increase the aggressiveness and road presence of your vehicle's front end. The high gloss finish looks very high quality and the OEM style carbon fiber will visually match any OEM carbon fiber on your vehicle. Details:- 100% pure prepreg carbon fiber construction- X-style design- High gloss finish- Fit guarantee: fits plug-and-play- Quick and easy installation- Supplied with pre-mounted 3M double-sided adhesive tape- Registration according to §21 possible Compatible vehicles:- BMW G80 M3/ Competition Sedan (2021+)- BMW G81 M3 Competition Touring (2021+)- BMW G82 M4/ Competition Coupe (2021+)- BMW G83 M4 Competition Convertible (2021+)Note: This is NOT an original BMW product!

The instrument surround made of pre-impregnated carbon fiber adds a touch of class to your vehicle's interior. When you buy Pre-Preg carbon fibre, you are investing in a higher quality and more durable material that will outlast other forms of carbon fibre and potentially save you money in the long run. Installation: Plug&Play Details:- 100% carbon fibre construction- High gloss finish- registration free Compatible vehicles:- BMW G87 M2 models- BMW G80 M3 Sedan models- BMW G81 M3 Touring models- BMW G82 M4 Coupé models- BMW G83 M4 Convertible models Note: This is NOT an original BMW product!

Our high-quality intake covers made from pre-preg carbon fibre is a great addition to enhance the style of your vehicle. When you buy Pre-Preg carbon fibre, you are investing in a higher quality and more durable material that will outlast other forms of carbon fibre and potentially save you money in the long run. Installation: Plug&Play Details: - Constructed from 100% pure prepreg carbon fiber - OEM-style weave - Complete OEM replacement - Guaranteed fit - Includes all necessary hardware - 3-year warranty - Registration-free Compatible vehicles with S58 engine:- BMW G87 M2 - BMW G80 M3 Sedan (2021+)- BMW G80 M3 Competition Sedan (2021+)- BMW G81 M3 Touring (2023+)- BMW G81 M3 Competition Touring (2023+)- BMW G82 M4 Coupé (2021+)- BMW G82 M4 Competition Coupé (2021+)- BMW G83 M4 Convertible (2021+)- BMW G83 M4 Competition Convertible (2021+) Note: This is NOT an original BMW product!

The BMW EVO 1 intake manifold with integrated intercooler for the B58.1 engine is suitable for the following vehicles:BMW 1 Series F20/21 M140iBMW 2 Series F22/23 M240iBMW 3 Series F30/31 340iBMW 4 Series F32/33/36 440i Unleash the full potential of your 3.0 liter B58.1 turbo engine with the revolutionary Wagner Tuning intake manifold with integrated intercooler. This innovative upgrade takes your performance to a new level and provides the ultimate driving experience. With a new type of performance mesh specially developed for the high demands of the B58.1 engine, the Wagner Tuning intake manifold offers an impressive 128% increase in external mesh volume compared to the original intercooler. The optimal ratio between the inner and outer cooling surface achieves maximum heat transfer while ensuring optimal internal airflow. Thanks to advanced CFD simulations, the CNC-milled end boxes have been designed for optimal airflow conditions, resulting in outstanding cooling performance with minimal back pressure. This kit is therefore also ideal for racing and guarantees optimum cooling of the supercharged air with a significant increase in performance. The Wagner Tuning intercoolers are also equipped with a thermally conductive anti-corrosion coating, which ensures a long-lasting and efficient cooling effect. Installation of the system is straightforward thanks to our simple installation instructions, allowing for a plug-and-play experience. The advantages of this product:- Significantly improved cooling performance with up to 20° lower intake air temperatures- Maximum relief of the turbocharger with 35% less back pressure- More power and torque for your engine- 100% pressure resistance for optimum safety- Plug-and-play without modifications- Prepared intake manifold injection- Three 1/8 NPT connections for additional parameter measurement- Six prepared NOS or WMI ports for optional upgrades - Suitable for all power levels- Up to 4-year warranty for peace of mind- Important information for the oil service: The oil filter can still be replaced without having to remove the intake manifold again! Get ready to dominate the road and unleash the full potential of your engine. Opt for the Wagner Tuning intake manifold with integrated intercooler and experience a whole new dimension of power and performance! Scope of delivery:1 intercooler2 silicone hoses4 hose clamps1 mounting material1 assembly instructionAttention: Not approved in the area of the StVZO.

The intake manifold with integrated intercooler EVO 1 is suitable for the following models:BMW 2 Series G42 M240iBMW 3 Series G20/G21 M340iBMW 4 Series G22/G23/G26 M440iBMW Z4 G29 M40iBMW X3 G01 M40iToyota GR Supra MK5 Immerse yourself in a new dimension of performance and experience a powerful increase in power for your 3.0 liter B58.2 turbo engine with our state-of-the-art intake manifold. The integrated intercooler, which is placed directly in the intake manifold, enables an efficient cooling process of the charge air and thus ensures optimum performance. Our Wagner Tuning intake manifold with integrated intercooler was specially developed for the high demands and tight space conditions of the B58.2 engine. With its innovative performance mesh, it offers an impressive 128 % larger external mesh volume compared to the original intercooler. The optimum ratio between the inner and outer cooling surface achieves maximum heat transfer while ensuring the best possible inner airflow. The CNC-milled end boxes, which have been optimized using CFD simulations, ensure outstanding cooling properties with minimal back pressure. This kit is therefore also perfect for racing and enables optimum cooling of the supercharged air with an impressive increase in performance. Our Wagner Tuning intake manifold is equipped with a thermally conductive anti-corrosion coating that ensures a long-lasting cooling effect and provides optimum protection for your engine. Installation of the system is uncomplicated thanks to our installation instructions and can be carried out “plug-and-play” without any problems. Benefit from the advantages of this product:- A significantly improved cooling performance for up to 20° cooler intake air temperatures.- Maximum mechanical and thermal relief of the turbocharger for a longer engine life and 35% less back pressure.- More power and torque for a breathtaking driving experience.- 100% pressure resistance for reliable performance.- Easy “plug and play” installation without modifications.- Prepared intake manifold injection- Three 1/8 NPT ports for additional measurement of parameters.- Six prepared NOS or WMI ports- Suitable for all performance levels, from street to racing.- Up to 4 years warranty for your complete satisfaction.- Important information for the oil service: The oil filter can still be carried out without having to dismantle the intake manifold again Experience the ultimate performance with our Wagner Tuning intake manifold with integrated intercooler and take your vehicle to a new level of performance! Scope of delivery:1 intercooler2 silicone air hoses5 retaining plates1 mounting material1 installation instructionAttention: Not approved in the area of the StVZO.

Intake manifold with integrated intercooler BMW M3/M4 suitable for the following models with S58 engine: BMW G87 M2 338kW/460 hp BMW G80/G81 M3 353-375kW/480-510hp BMW G82 M4 353-405kW/480-550hpWith combined expert opinion! Discover the revolution in performance optimisation for your 3.0-litre S58 turbo engine with the innovative Wagner Tuning intake manifold with integrated intercooler. Developed to meet the high demands of the S58 engine, this exceptional kit features a special competition mesh that has an impressive 50% larger outer mesh volume compared to the original intercooler. The optimal ratio between inner and outer cooling surface maximises heat transfer while ensuring the best possible inner airflow. The end boxes made of high-quality aluminium chill casting have been designed for optimum air flow conditions using CFD simulations, resulting in outstanding cooling properties with minimal back pressure. This kit is the perfect choice. Our Wagner Tuning intercoolers are equipped with a thermally conductive anti-corrosion coating to ensure maximum durability and performance. The installation of the system is straightforward thanks to our detailed installation instructions and can easily be carried out as plug & play. Enjoy the many benefits of this product: - Achieve significantly improved cooling performance with intake air temperatures that are up to 20° cooler. - Relieve your turbocharger both mechanically and thermally to the maximum. - Experience an impressive increase in power and torque for your engine. - Benefit from 100% pressure resistance and reliability. - The plug-and-play function enables easy installation without modifications. - The intake manifold is suitable for use with prepared intake manifold injectors (Fuel Rail optionally available here ). - Use the 1/8 NPT connections to measure and monitor additional parameters. - This intake manifold is ideal for all power levels. Get your engine ready for unrivalled performance and take your driving experience to the next level. Opt for the Wagner Tuning intake manifold with integrated intercooler and experience a new dimension of power, speed and driving pleasure. Discover the limits of what is possible and take your performance to the next level.

The Aulitzky Tuning intake manifold for the S58 engines of the G8x series was developed to meet the high demands of the engine. Advantages: - Improved cooling performance with up to 20° cooler intake air temperatures - Maximum mechanical and thermal relief for the turbocharger - Increase in power and torque - Absolute pressure resistance and reliability - Easy installation thanks to plug-and-play - 1/8 NPT connections for measuring and monitoring additional parameters - Optimally suited for all performance levels With combination certificate!* Compatible vehicles:VehicleVehicle typePowerCapacityEngineYear of construction BMW 2er (G87)M2338kW / 460hp2993cm³S58 B30 A11.22 - BMW 3 Series (G80)M3353kW / 480hp2993cm³S58 B30 B11.20 - BMW 3 Series (G80/G81)M3 Competition / xDrive375kW / 510hp390kW / 530hp2993cm³S58 B30 A05.21 -07.24 - BMW 3 Series (G80)M3 CS xDrive405kW / 551hp2993cm³S58 B30 A03.23 - BMW 4 Series (G82)M4353kW / 480hp2993cm³S58 B30 B11.20 - BMW 4 Series (G82/G83)M4 Competition / M xDrive375kW / 510hp2993cm³S58 B30 A11.20 - BMW 4 Series (G82)M4 CSL xDrive405kW / 551hp412kW / 560hp2993cm³S58 B30 A05.22 - 02.2311.22 - 02.23 *The combination certificate for the pre-facelift and facelift models is available (includes intake manifold, intake, intercooler, boost pipe kit, downpipe, exhaust system, 670hp Aulitzky App performance increase and 107dB increase in stationary noise).

Facts: Brand Eventuri Material carbon Mounting: like original part (exchange) Expertise: without ATTENTION: All models built before 2018 still have a mass air flow sensor installed. All models built after 2018 have a temperature sensor. There are therefore two different products for both engine variants. The G20/G21 B48 Eventuri intake system was developed to provide the turbo with a less restrictive flow path while maintaining low intake temperatures. When designing an intake system for turbocharged engines, the focus is on heat and volume. On the G20, the intake system is located next to the exhaust manifold, which quickly fills the engine bay with heat. High temperatures have a detrimental effect on engine performance as the turbo would have to be charged with heated, less dense air, so the only way to minimise IATs is to have a fully sealed intake. However, this leads to a restriction with only one supply air inlet from which air is drawn. During development, we identified an additional opening in the wheel arch area and took advantage of this by adding a second intake to our airbox. In addition, our sealed airbox also features a gold reflective heat shield to minimise radiant heat transfer from the exhaust manifold. To maximise volume, we have made the airbox as large as possible with a recess for potential strut bracing. The standard corrugated intake pipe has been replaced with a smooth carbon pipe, which also has a larger internal volume with an initial internal diameter of 111 mm (4.4") and tapers gently downwards to match the turbo inlet. The pipe provides a smooth path from the filter to the turbo inlet. Finally, we use a customised high-flow dry filter that is ISO-tested for filtration performance and has a larger filter area than the standard filter. The G20/G21 B48 Eventuri intake system consists of a number of components designed for a specific purpose and manufactured to the highest standards. We use 100% prepreg carbon fibre with no glass fibre, which means we can achieve a smooth internal surface to get a smoother airflow. Here are the details for each component and the design ethos behind it: Each intake system consists of: Carbon airbox with two inlets Customised high flow dry cone filter Carbon fibre inlet pipe Bracket for CNC-machined temperature sensor CNC-machined vent adapter Heat shield with reflective gold foil Laser-cut stainless steel brackets Silicone reducer with clamps according to OEM specification Compatible vehicles: VehicleTypePowerEngine capacityEngine type 3 Series (G20/G21)318i115kW / 156hp1998cm³B48 B20 A 3 Series (G20/G21)320i / xDrive135kW / 184hp1998cm³B48 B20 A, B48 B20 B 3 Series (G20/G21)330i / xDrive180kW / 245hp190kW / 258hp1998cm³B48 B20 B

Facts: Material: Carbon Manufacturer: Eventuri Parts certificate: For this product a certificate is available for certain regions and vehicles (details below) The Eventuri Carbon Kevlar Intake System for the F Series is designed to increase engine performance, improve handling and enhance the overall driving experience. Using an inverted cone-shaped filter enclosed in a carbon/kevlar housing, Eventuri utilises the so-called Venturi effect. The result is a uniform laminar airflow, which not only provides more power but also better responsiveness and a new sound experience. Since January 2019, the Eventuri system has been sold with a new, closed airflow. The closed system restricts the airflow to fresh air and prevents warm engine air from entering from the heat exchanger. The heat shields also shield the cold airflow from radiating engine heat and the airbox is manufactured using the pre-preg process. The parts certificate is included in the scope of delivery. Parts certificate The manufacturer's specifications apply for installation. An existing certificate is no guarantee that the product can also be installed in the corresponding vehicle. A certificate is available for this product for the following regions and vehicles: * DE/AT: Vehicle registration document, field K --- CH/LI: Vehicle licence, field 24 Country Model Type approval* DE/AT BMW 1 Series (1K2) e1*xx/xx*0273*.. DE/AT BMW 1 Series (1K2) e1*xx/xx*0283*.. DE/AT BMW 1 Series (1K4) e1*xx/xx*0273*.. DE/AT BMW 1 Series (1K4) e1*xx/xx*0283*.. DE/AT BMW 2 Series (1C) e1*xx/xx*0277*.. DE/AT BMW 3 Series (3K) e1*xx/xx*0314*.. DE/AT BMW 3 Series (3K) e1*xx/xx*0315*.. DE/AT BMW 3 Series (3L) e1*xx/xx*0314*.. DE/AT BMW 3 Series (3L) e1*xx/xx*0315*.. DE/AT BMW 4 Series (3C) e1*xx/xx*0316*.. DE/AT BMW M2 e1*xx/xx*0377*.. CH/LI BMW M2 1BG874 CH/LI BMW M2 1BJ924 Compatible vehicles:VehicleTypePowerEngine capacityEngine typeYear of construction BMW 1 Series (F20/F21)M135i / xDrive235kW / 320hp240kW / 326hp2979cm³N55 B30 A12.11 - 02.1503.15 - 06.16 BMW 2 Series (F22/F23)M235i / xDrive240kW / 326hp2979cm³N55 B30 A10.13 - 06.16 BMW 2 Series Coupe (F87)M2272kW / 370hp2979cm³N55 B30 A11.15 - 06.18 BMW 3 Series (F30/F31/F34)335i / xDrive225kW / 306hp240kW / 326hp250kW / 326hp2979cm³N55 B30 A11.11 - 07.1511.11 - 06.1307.13 - 06.16 BMW 4 Series (F32/F33/F36)435i / xDrive225kW / 306hp250kW / 340hp2979cm³N55 B30 A07.13 - 02.16

Facts: Increase in performance by 12 - 15 hp Material: Carbon Manufacturer: Eventuri Parts certificate: A certificate is available for this product for certain regions and vehicles (details below) With the new announcement system for the F Series with B58 engine, Eventuri has once again set new standards in the combination of efficiency and design. The patented full carbon filter housing has been processed with the intake pipe in one continuous piece to channel the airflow into the turbo in an even more compressed and laminar manner. The newly arranged main heat shield consists of 2 parts separated by a thin air slot. The ingenious design creates a cooling air suction between the shields and thus improves the shielding of the airflow. The increase in performance is guaranteed by a cool, compressed airflow. The intake system alone provides an uplift in performance of 12 - 15 hp! The intake system comes with the following patented components: Carbon filter housing with integrated inlet pipe Efficient high-flow cone with urethane filter Aluminium bonnet Carbon scoop Carbon filter sleeve CNC MAF Boss 2-piece main heat shield 2-piece secondary heat shield Laser-cut suspension The carbon housing shields the filter from the outside, but is also the essential part in shaping the airflow. The conical constriction of the filter housing compresses and accelerates the airflow without heating it up. The resulting Venturi effect ensures an optimum airflow to the turbo and thus increases the performance of the engine. Parts certificate The manufacturer's specifications apply to installation. An existing certificate is no guarantee that the product can also be installed in the corresponding vehicle. A certificate is available for this product for the following regions and vehicles: * DE/AT: Vehicle registration document, field K --- CH/LI: Vehicle licence, field 24 Country Model Type approval* DE/AT BMW 340i (3K) e1*2007/46*0315*.. DE/AT BMW 340i (3L) e1*2007/46*0314*.. DE/AT BMW 340i (3-V) e1*2007/46*0559*.. DE/AT BMW 340i xDrive (3K) e1*2007/46*0315*.. DE/AT BMW 340i xDrive (3L) e1*2007/46*0314*.. DE/AT BMW 340i xDrive (3-V) e1*2007/46*0559*.. DE/AT BMW 440i (3C) e1*2007/46*0316*.. DE/AT BMW 440i xDrive (3C) e1*2007/46*0316*.. DE/AT BMW M140i (1K2) e1*2007/46*0273*.. DE/AT BMW M140i (1K4) e1*2007/46*0283*.. DE/AT BMW M140i xDrive (1K2) e1*2007/46*0273*.. DE/AT BMW M140i xDrive (1K4) e1*2007/46*0283*.. DE/AT BMW M240i (1C) e1*2007/46*0277*.. DE/AT BMW M240i xDrive (1C) e1*2007/46*0277*..Compatible vehicles:VehicleTypePowerEngine capacityEngine typeYear of construction BMW 1 Series (F20/F21)M140i / xDrive250kW / 340hp2998cm³B58 B30 A09.15 - BMW 2 Series (F22/F23)M240i / xDrive250kW / 340hp2998cm³B58 B30 A09.15 - 06.21 BMW 3 Series (F30/F31/F34)340i / xDrive240kW / 326hp265kW / 360hp2998cm³B58 B30 A07.15 - 10.18 BMW 4 Series (F32/F33/F36)440i / xDrive240kW / 326hp265kW / 360hp2998cm³B58 B30 A03.16 - 06.20

Facts:Performance increase: 13-18hp, 12-16ft-lb (stock tune)Turbo inlet area increased by up to 160%Filtration area increased by up to 40%Material: CarbonManufacturer: EventuriParts certificate: A certificate is available for this product for certain regions and vehicles (details below) Introducing an intake that truly sets a new benchmark for the G8X platform. We have undertaken intensive research and development to create an intake system that not only outperforms the standard vehicle, but is also future proofed for power increases well in excess of 1000hp. Our system is a complete redesign from the airboxes to the turbo inlets with the aim of reducing pressure loss while increasing flow rate and keeping inlet temperatures low. We have maximized the use of available space and used 2 custom made filters with a 40% larger filter area than stock. These are used in our patented Venturi housings to direct the air evenly to the turbo inlets. The inlets themselves have a cross section up to 160% larger than standard and are fitted with an advanced dimpled inner surface to reduce frictional losses between the flow and the wall boundary. By creating an air "cushion" on the wall surface, the airflow can move through the inlets at higher flow rates and lower pressure drop. This allows the turbos to draw in air with less resistance, reducing the wastegate duty cycle, resulting in higher overall performance. Bench testThis intake system was independently bench tested by BR Performance in Belgium. The tests were carried out back-to-back with the standard airbox and several runs were made with each configuration. The tested vehicle was driven without an activated carbon filter. We compared the best results with the standard airbox and the best results with the Eventuri system. The results on the dyno show a constant increase across the entire rev range, which is due to the turbos reaching maximum boost pressure earlier and having a lower wastegate duty cycle due to the higher efficiency of the intake system. This increase is despite the increase in dyno temperatures from 11.8 degrees Celsius in the tests with the standard system to almost 16 degrees Celsius in the Eventuri tests. The increase in performance is reflected on the road in improved response at part and full throttle, with the car pulling much more eagerly to the red line. Intake air temperature testsIn vehicles with turbochargers, a lot of heat can build up in the engine compartment, which can have a detrimental effect on performance if the intake system is not sealed against this heat. Even with intercoolers and charge air coolers, it is important to minimize intake air temperatures as these cooling devices operate at a certain efficiency, so the output air temperature is affected by the input air temperature. Restricting the intake tract with open cones, even if they are heat protected, will inevitably draw hot air from the engine bay. Our system, which is completely sealed, solves this problem, while still not restricting the flow path by using larger volumes. To demonstrate this, we recorded the air temperatures with thermocouples immediately before each turbo. The comparisons were made on the same day and under the same environmental conditions between the original and Eventuri. Our vehicle was allowed to warm up and then accelerated from 30mph to 90mph in 6th gear to measure the temperature change on each run. The car was accelerated in 6th gear to measure the temperature change with each run. At 90mph, the gas pedal was released and the brakes applied to 30mph, after which the car was accelerated back to 90mph. A total of 3 pull-throughs were performed with both intake configurations. Scope of delivery:- 2x patented Venturi filter housings made of carbon- 2x Bespoke dry cone filters with high flow rate- 2x carbon intake pipes- 1x carbon intake pipe- 2 thermoplastic turbo inlets- Laser-cut stainless steel brackets- Customized flexible hose- CNC machined brackets and reinforcement rings For this product a certificate is available for the following regions and vehicles:* DE/AT: Vehicle registration document, field K --- CH/LI: Vehicle registration document, field 24Country model type approval*DE/AT BMW M2 e1*2018/858*00211*..DE/AT BMW M3 e1*2018/858*00003*..DE/AT BMW M3 Competition e1*2018/858*00003*..DE/AT BMW M3 Competition M xDrive e1*2018/858*00003*..DE/AT BMW M3 CS e1*KS18/858*00008*..DE/AT BMW M4 e1*2018/858*00003*..DE/AT BMW M4 Competition e1*2018/858*00003*..DE/AT BMW M4 Competition M xDrive e1*2018/858*00003*..DE/AT BMW M4 CSL e1*KS18/858*00008*..CH/LI BMW G234M WBS31AYCH/LI BMW G234M WBS31AZCH/LI BMW G234M WBS31BACH/LI BMW G234M WBS41AYCH/LI BMW G234M WBS41AZCH/LI BMW G234M WBS51AYCH/LI BMW G234M WBS51AZCH/LI BMW G34MKS WBS61AYCH/LI BMW G34MKS WBS61AZCH/LI BMW G34MKS WBS81AZCH/LI BMW M2 WBS11DMCH/LI BMW M3 / G234M WBS11GB Compatible vehicles:VehicleVehicle typePowerEngine capacityEngine typeYear of construction BMW 2 (G87)M2338kW / 460hp353kW / 480hp2993cm³S58 B30 B11.20 - BMW 3 (G80)M3353kW / 480hp2993cm³S58 B30 B11.20 - BMW 3 (G80/G81)M3 Competition / xDrive375kW / 510hp390kW / 530hp2993cm³S58 B30 A05.21 - BMW 3 (G80)M3 CS xDrive405kW / 551hp2993cm³S58 B30 A05.21 - BMW 4 (G82)M4353kW / 480hp2993cm³S58 B30 B11.20 - BMW 4 (G82/G83)M4 Competition / M xDrive375kW / 510hp2993cm³S58 B30 A05.21 - BMW 4 (G82/G83)M4 CSL xDrive405kW / 551hp412kW / 560hp2993cm³S58 B30 A05.21 -

Facts:The intake generates +17 hp / +19 Nm with a series M4Material: CarbonManufacturer: EventuriParts certificate: A certificate is available for this product for certain regions and vehicles (details below) ATTENTION: The variant with the aluminum scoops is the V1 Cariante, i.e. without the closed ducts. In an effort to make their products as good as possible for every customer and every application, the well-known intake system F-series has been revised.A new feature is the completely closed air duct, as opposed to the semi-open one in the old system. For all owners of the old system, there is now an upgrade kit with which the half-open air ducts can be closed. In the “Carbon” version, the intake is always the new, closed V2 intake. The Eventuri carbon intake system was developed to increase engine performance, improve handling and enhance the overall driving experience. With an inverted cone-shaped filter, enclosed in a carbon/Kevlar housing, Eventuri utilizes the so-called Venturi effect. The result is an even laminar airflow, which not only provides more power but also better responsiveness and a new sound experience.the airbox is manufactured using the pre-preg process. The intake generates +17 hp / +19 Nm with a standard vehicle. An official parts certificate is included. Parts certificateThe manufacturer's specifications apply to installation. An existing certificate is no guarantee that the product can also be installed in the corresponding vehicle. A certificate is available for this product for the following regions and vehicles:* DE/AT: Vehicle registration document, field K --- CH/LI: Vehicle registration document, field 24Country Model Type approval*CH/LI BMW M3 1BF119CH/LI BMW M3 1BG467CH/LI BMW M3 1XK810CH/LI BMW M3 GTS 1BG950CH/LI BMW M4 1BF120CH/LI BMW M4 1BJ693CH/LI BMW M4 1BJ696CH/LI BMW M4 1BJ927CH/LI BMW M4 Convertible 1BF695CH/LI BMW M4 Convertible 1BF929CH/LI BMW M4 Convertible 1BJ694CH/LI BMW M4 Convertible 1XR665CH/LI BMW M4 CS 1BJ931 Compatible vehicles:VehicleVehicle typePowerEngine capacityEngine typeYear of construction BMW 3er (F80)M3317kW / 431hp2979cm³S55 B30 A03.14 - 10.18 BMW 3er (F80)M3 Competition331kW / 450hp2979cm³S55 B30 A03.16 - 10.18 BMW 3er (F80)M3 CS338kW / 460hp2979cm³S55 B30 A01.18 - 10.18 BMW 4er (F82/F83)M4317kW / 431hp2979cm³S55 B30 A03.14 - 07.20 BMW 4er (F82/F83)M4 Competition331kW / 450hp2979cm³S55 B30 A03.16 - 07.20 BMW 4er Coupe (F82)M4 CS338kW / 460hp2979cm³S55 B30 A07.17 - 06.19 BMW 4er Coupe (F82)M4 GTS368kW / 500hp2979cm³S55 B30 A03.16 - 06.19

CSF Race intercooler / with parts certificate! A large intercooler is a must if you expect the best possible performance from your vehicle. The stock intercoolers are great for everyday use, but do not meet the airflow and cooling requirements when used on the race track or on performance tuned vehicles. CSF remedies this situation with their all new High Performance intercooler. The cooler is suitable for all petrol and diesel engines in the 1 to 4 Series F series! The advantages at a glance:- “Stepped core design” for maximum surface contact and internal intake air flow volume.- Largest drop-in fit intercooler in the industry with 17 rows - Developed with 3D scanning / rapid prototyping technology to ensure precise fitting and maximum surface area utilization.- Lab tested at CSF's in-house wind tunnel. - Rounded faceplate / panel design for optimized airflow through the core.- Drop-in fit design for quick and easy plug-and-play installation. Complete with “Quick-Connect” -OEM style auto/outlet connectors.- Fully reversible with no modifications required.- Available in silver or matt black- Lifetime warranty- 25 degrees cooler intake temperature compared to stock, even after multiple accelerations- Performance increase of 15-20 hp on stock cars, 25+ hp on modified cars. Technical data:Internal Fin Height: 6.5Internal Fin Pitch: 3.4Internal Fin Q'ty: 15External Fin Height: 6.5External Fin Pitch: 4.0External Fin Q'ty: 17Width (mm): 235Net size (L*H*W) in mm: 510*140*235Surface area: 13.7 cm³ Compatible vehicles:BMW    1 (F20)    114 d    2012-2019BMW    1 (F20)    114 i    2012-2019BMW    1 (F20)    116 d    2011-2015BMW    1 (F20)    116 i    2011-2019BMW    1 (F20)    118 d    2011-2019BMW    1 (F20)    118 d xDrive    2013-2019BMW    1 (F20)    118 i    2011-2019BMW    1 (F20)    120 d    2011-2019BMW    1 (F20)    120 d xDrive    2012-2019BMW    1 (F20)    120 i    2015-2019BMW    1 (F20)    125 d    2012-2019BMW    1 (F20)    125 i    2012-2019BMW    1 (F20)    125 i Active Flex    2014-2017BMW    1 (F20)    M 135 i    2012-2016BMW    1 (F20)    M 135 i xDrive    2012-2016BMW    1 (F20)    M 140 i    2016-2019BMW    1 (F20)    M 140 i xDrive    2016-2019 BMW    1 (F21)    114 d    2012-2019BMW    1 (F21)    114 i    2012-2015BMW    1 (F21)    116 d    2011-2019BMW    1 (F21)    116 i    2011-2019BMW    1 (F21)    118 d    2011-2019BMW    1 (F21)    118 d xDrive    2013-2019BMW    1 (F21)    118 i    2012-2019BMW    1 (F21)    120 d    2012-2019BMW    1 (F21)    120 d xDrive    2012-2019BMW    1 (F21)    120 i    2015-2019BMW    1 (F21)    125 d    2011-2019BMW    1 (F21)    125 i    2011-2019BMW    1 (F21)    M 135 i    2011-2016BMW    1 (F21)    M 135 i xDrive    2012-2016BMW    1 (F21)    M 140 i    2015-2019BMW    1 (F21)    M 140 i xDrive    2015-2019 BMW    2 Cabriolet (F23)    218 d    2015-2020BMW    2 Cabriolet (F23)    218 i    2015-2021BMW    2 Cabriolet (F23)    220 d    2014-2020BMW    2 Cabriolet (F23)    220 i    2014-2021BMW    2 Cabriolet (F23)    225 d    2015-2019BMW    2 Cabriolet (F23)    225 i    2017-2021BMW    2 Cabriolet (F23)    228 i    2014-2016BMW    2 Cabriolet (F23)    230 i    2016-2021BMW    2 Cabriolet (F23)    M 235 i    2014-2016BMW    2 Cabriolet (F23)    M 235 i xDrive    2015-2016BMW    2 Cabriolet (F23)    M 240 i    2015-2021BMW    2 Cabriolet (F23)    M 240 i xDrive    2015-2021 BMW    2 Coupe (F22, F87)    218 d    2014-2020BMW    2 Coupe (F22, F87)    218 i    2015-2021BMW    2 Coupe (F22, F87)    220 d    2012-2020BMW    2 Coupe (F22, F87)    220 d xDrive    2014-2020BMW    2 Coupe (F22, F87)    220 i    2013-2021BMW    2 Coupe (F22, F87)    225 d    2014-2019BMW    2 Coupe (F22, F87)    228 i    2014-2016BMW    2 Coupe (F22, F87)    230 i    2016-2021BMW    2 Coupe (F22, F87)    M 235 i    2013-2016BMW    2 Coupe (F22, F87)    M 235 i xDrive    2014-2016BMW    2 Coupe (F22, F87)    M 240 i    2015-2021BMW    2 Coupe (F22, F87)    M 240 i xDrive    2015-2021 BMW    3 (F30, F80)    316 d    2012-2018BMW    3 (F30, F80)    316 i    2012-2016BMW    3 (F30, F80)    318 d    2012-2018BMW    3 (F30, F80)    318 d xDrive    2013-2018BMW    3 (F30, F80)    318 i    2015-2018BMW    3 (F30, F80)    320 d    2011-2018BMW    3 (F30, F80)    320 d xDrive    2012-2018BMW    3 (F30, F80)    320 i    2012-2018BMW    3 (F30, F80)    320 i xDrive    2012-2018BMW    3 (F30, F80)    325 d    2013-2018BMW    3 (F30, F80)    328 i    2011-2018BMW    3 (F30, F80)    328 i xDrive    2012-2016BMW    3 (F30, F80)    330 d    2012-2018BMW    3 (F30, F80)    330 d xDrive    2013-2018BMW    3 (F30, F80)    330 e    2015-2018BMW    3 (F30, F80)    330 i    2015-2018BMW    3 (F30, F80)    330 i xDrive    2015-2018BMW    3 (F30, F80)    335 d xDrive    2013-2018BMW    3 (F30, F80)    335 i    2011-2015BMW    3 (F30, F80)    335 i xDrive    2012-2015BMW    3 (F30, F80)    340 i    2015-2018BMW    3 (F30, F80)    340 i xDrive    2015-2018BMW    3 (F30, F80)    ActiveHybrid    2012-2015 BMW    3 Gran Turismo (F34)    318 d    2013-BMW    3 Gran Turismo (F34)    320 d    2013-BMW    3 Gran Turismo (F34)    320 d xDrive    2013-BMW    3 Gran Turismo (F34)    320 i    2013-BMW    3 Gran Turismo (F34)    320 i xDrive    2012-BMW    3 Gran Turismo (F34)    325 d    2013-2018BMW    3 Gran Turismo (F34)    328 i    2013-2016BMW    3 Gran Turismo (F34)    328 i xDrive    2013-2016BMW    3 Gran Turismo (F34)    330 d    Seit 2014BMW    3 Gran Turismo (F34)    330 d xDrive    Seit 2014BMW    3 Gran Turismo (F34)    330 i    Seit 2016BMW    3 Gran Turismo (F34)    330 i xDrive    Seit 2016BMW    3 Gran Turismo (F34)    335 d xDrive    Seit 2014BMW    3 Gran Turismo (F34)    335 i    2013-2016BMW    3 Gran Turismo (F34)    335 i xDrive    2013-2016BMW    3 Gran Turismo (F34)    340 i    Seit 2016BMW    3 Gran Turismo (F34)    340 i xDrive    Seit 2016 BMW    3 Touring (F31)    316 d    2012-2019BMW    3 Touring (F31)    316 i    2013-2015BMW    3 Touring (F31)    318 d    2012-2019BMW    3 Touring (F31)    318 d xDrive    2013-2018BMW    3 Touring (F31)    318 i    2015-2019BMW    3 Touring (F31)    320 d    2012-2019BMW    3 Touring (F31)    320 d xDrive    2013-2019BMW    3 Touring (F31)    320 i    2012-2019BMW    3 Touring (F31)    320 i xDrive    2013-2019BMW    3 Touring (F31)    325 d    2013-2018BMW    3 Touring (F31)    328 i    2012-2015BMW    3 Touring (F31)    328 i xDrive    2013-2016BMW    3 Touring (F31)    330 d    2012-2019BMW    3 Touring (F31)    330 d xDrive    2013-2019BMW    3 Touring (F31)    330 i    2015-2019BMW    3 Touring (F31)    330 i xDrive    2015-2019BMW    3 Touring (F31)    335 d xDrive    2013-2019BMW    3 Touring (F31)    335 i    2013-2015BMW    3 Touring (F31)    335 i xDrive    2013-2015BMW    3 Touring (F31)    340 i    2015-2019BMW    3 Touring (F31)    340 i xDrive    2015-2019 BMW    4 Cabriolet (F33, F83)    420 d    2013-2020BMW    4 Cabriolet (F33, F83)    420 i    2014-2020BMW    4 Cabriolet (F33, F83)    425 d    2014-2018BMW    4 Cabriolet (F33, F83)    428 i    2013-2017BMW    4 Cabriolet (F33, F83)    428 i xDrive    2014-2016BMW    4 Cabriolet (F33, F83)    430 d    2014-2020BMW    4 Cabriolet (F33, F83)    435 d xDrive    2014-2020BMW    4 Cabriolet (F33, F83)    435 i    2013-2016BMW    4 Cabriolet (F33, F83)    435 i xDrive    2014-2016BMW    4 Cabriolet (F33, F83)    440 i    2016-2020BMW    4 Cabriolet (F33, F83)    440 i xDrive    2016-2020 BMW    4 Coupe (F32, F82)    418 d    2015-2017BMW    4 Coupe (F32, F82)    418 i    2016-2020BMW    4 Coupe (F32, F82)    420 d    2013-2020BMW    4 Coupe (F32, F82)    420 d xDrive    2013-2020BMW    4 Coupe (F32, F82)    420 i    2013-2020BMW    4 Coupe (F32, F82)    420 i xDrive    2013-2020BMW    4 Coupe (F32, F82)    425 d    2014-2017BMW    4 Coupe (F32, F82)    428 i    2013-2017BMW    4 Coupe (F32, F82)    428 i xDrive    2013-2016BMW    4 Coupe (F32, F82)    430 d    2013-2020BMW    4 Coupe (F32, F82)    430 d xDrive    2014-2020BMW    4 Coupe (F32, F82)    430 i    2016-BMW    4 Coupe (F32, F82)    430 i xDrive    2016-2020BMW    4 Coupe (F32, F82)    435 d xDrive    2013-2020BMW    4 Coupe (F32, F82)    435 i    2013-2016BMW    4 Coupe (F32, F82)    435 i xDrive    2013-2016BMW    4 Coupe (F32, F82)    440 i    2016-2020BMW    4 Coupe (F32, F82)    440 i xDrive    2016-2020 BMW    4 Gran Coupe (F36)    418 d    2014-2020BMW    4 Gran Coupe (F36)    418 i    2015-2020BMW    4 Gran Coupe (F36)    420 d    2014-2020BMW    4 Gran Coupe (F36)    420 d xDrive    2014-2020BMW    4 Gran Coupe (F36)    420 i    2014-2021BMW    4 Gran Coupe (F36)    420 i xDrive    2014-2021BMW    4 Gran Coupe (F36)    425 d    2016-2018BMW    4 Gran Coupe (F36)    428 i    2014-2016BMW    4 Gran Coupe (F36)    428 i xDrive    2014-2016BMW    4 Gran Coupe (F36)    430 d    2014-2020BMW    4 Gran Coupe (F36)    430 d xDrive    2014-2020BMW    4 Gran Coupe (F36)    430 i    2016-2021BMW    4 Gran Coupe (F36)    430 i xDrive    2016-2021BMW    4 Gran Coupe (F36)    435 d xDrive    2014-2020BMW    4 Gran Coupe (F36)    435 i    2014-2016BMW    4 Gran Coupe (F36)    435 i xDrive    2014-2016BMW    4 Gran Coupe (F36)    440 i    2016-2021BMW    4 Gran Coupe (F36)    440 i xDrive    2016-2021 TeilegutachtenFür den Einbau gelten die Angaben des Herstellers. Ein vorhandenes Gutachten ist keine Garantie dafür, dass das Produkt auch im entsprechenden Fahrzeug eingebaut werden kann.Für dieses Produkt ist ein Gutachten für die folgenden Regionen und Fahrzeuge verfügbar:* DE/AT: Fahrzeugschein, Feld K --- CH/LI: Fahrzeugausweis, Feld 24Länder     Modell     Typgenehmigung*DE/AT    BMW 114i     e1*xx/xx*0273*..DE/AT    BMW 114i     e1*xx/xx*0277*..DE/AT    BMW 114i     e1*xx/xx*0283*..DE/AT    BMW 116i     e1*xx/xx*0273*..DE/AT    BMW 116i     e1*xx/xx*0277*..DE/AT    BMW 116i     e1*xx/xx*0283*..DE/AT    BMW 118i     e1*xx/xx*0273*..DE/AT    BMW 118i     e1*xx/xx*0277*..DE/AT    BMW 118i     e1*xx/xx*0283*..DE/AT    BMW 125i     e1*xx/xx*0273*..DE/AT    BMW 125i     e1*xx/xx*0277*..DE/AT    BMW 125i     e1*xx/xx*0283*..DE/AT    BMW 220i     e1*xx/xx*0277*..DE/AT    BMW 228i     e1*xx/xx*0277*..DE/AT    BMW 316i     e1*xx/xx*0314*..DE/AT    BMW 316i     e1*xx/xx*0315*..DE/AT    BMW 316i     e1*xx/xx*0559*..DE/AT    BMW 320i     e1*xx/xx*0314*..DE/AT    BMW 320i     e1*xx/xx*0315*..DE/AT    BMW 320i     e1*xx/xx*0559*..DE/AT    BMW 328i     e1*xx/xx*0314*..DE/AT    BMW 328i     e1*xx/xx*0315*..DE/AT    BMW 328i     e1*xx/xx*0559*..DE/AT    BMW 335i     e1*xx/xx*0314*..DE/AT    BMW 335i     e1*xx/xx*0315*..DE/AT    BMW 335i     e1*xx/xx*0599*..DE/AT    BMW 420i     e1*xx/xx*0316*..DE/AT    BMW 428i     e1*xx/xx*0316*..DE/AT    BMW 435i     e1*xx/xx*0316*..DE/AT    BMW M135i     e1*xx/xx*0273*..DE/AT    BMW M135i     e1*xx/xx*0277*..DE/AT    BMW M135i     e1*xx/xx*0283*..DE/AT    BMW M2     ab e1*xx/xx*0377*10DE/AT    BMW M235i     e1*xx/xx*0277*..CH/LI    BMW M2     1BG874CH/LI    BMW M2     1BJ924