Entry sill surround cover Carbon | fits BMW BMW 4 Series (G22) | Aulitzky Tuning

Facts:Performance increase: 15-20hpExpert opinion: withoutManufacturer: EventuriMaterial: CarbonExpert opinion: without The Mercedes A35 AMG Eventuri intake system was developed to provide the turbo with a less restrictive flow path while keeping intake temperatures low. Reducing heat suction and increasing internal volume are the main considerations when developing an intake system for turbocharged engines. In the A35, the intake system is located in close proximity to the exhaust manifold, which quickly heats up the engine compartment. High temperatures have a detrimental effect on engine performance, as the turbo has to build up boost pressure with heated, less dense air. Therefore, the only way to reduce IAT to a minimum is to have a completely sealed intake tract. To reduce the restrictions of a closed intake tract, we increased the volume of the airbox by relocating the ECU and providing an opening in the airbox on the cold side, away from the direct heat of the manifold. The carbon inlet pipe has a larger internal volume with an initial internal diameter of 111mm (4.4?) which tapers smoothly to match the turbo inlet pipe diameter. Finally, we use a custom high-flow dry filter that is ISO approved and has a larger filter area than the stock filter. Dyno testsThe dyno tests were carried out by MSL Performance, a Mercedes specialist based in the UK. A fully standard A35 AMG was tested with the standard airbox and then with the Eventuri intake system, with the same external conditions. As can be seen below, the intake system offers an increase in power throughout the rev range. The highlighted point shows a significant power gain as the intake allows a higher flow rate in the higher rev range where the stock airbox becomes a restriction. The resulting performance gains are noticeable on the road, with better throttle response and improved acceleration times. With a tuned A35 we would expect even better gains as the demand from the turbo increases. The Eventuri A35 intake system consists of a number of components designed for a specific purpose and manufactured to the highest standards. We use 100% pre-impregnated carbon fiber without fiberglass, which means we can achieve a smooth inner surface to get a smoother airflow. Here are the details for each component and the design ethos behind them: Each intake system consists of:Carbon airboxCustom high-flow dry-cone filterCarbon intake tubeCNC-machined intake flangeLaser-cut stainless steel brackets and ECU coverSilicone coupler with OEM clamps Compatible vehicles:VehicleVehicle typePowerEngine capacityEngine typeYear of construction Mercedes A-Klasse (W177/V177)A250 / 4-matic165kW / 224hp1991cm³M 260.92003.18 - Mercedes A-Klasse (W177/V177)A35 AMG 4-matic225kW / 306hp1991cm³M 260.92009.18 - Mercedes CLA (C118/X118)A250 / 4-matic165kW / 224hp1991cm³M 260.92003.19 - Mercedes CLA (C118/X118)CLA35 AMG 4-matic225kW / 306hp1991cm³M 260.92004.19 - Mercedes GLB (X247)GLB250 / 4-matic165kW / 224hp1991cm³M 260.92008.19 - Mercedes GLB (X247)GLB35 AMG 4-matic225kW / 306hp1991cm³M 260.92008.19 -

KW coilover suspension DDC ECU KW Dynamic Damping Control ECU Individuality at the push of a button. The KW DDC coilovers are the intelligent suspension solution for retrofitting from the KW iSuspension product range. They combine the advantages of an adaptive damping system with a vehicle-specific sporty and harmonious damper characteristic with a stylish and sporty lowering. The adaptive KW coilovers are available in the KW DDC ECU version with optional app control for vehicles without actively controlled standard suspension and as KW DDC Plug & Play version for selected vehicle models with adaptive standard suspension. The adaptive KW DDC ECU coilovers allow a stepless lowering in the tested adjustment range. Thanks to the dirt-resistant trapezoidal thread and the polyamide threaded ring, the stepless lowering can be varied quickly and easily even after years. Depending on the vehicle, lowering takes place either on the wheel-guiding KW stainless steel suspension struts or, in the case of non-wheel-guiding double wishbone rear axles, on the rear axle height adjustment. No matter where in the world, sporty drivers, car manufacturers and tuners trust in our KW technology “Made in Germany”. Every KW coilover suspension is subjected to extensive load tests during production and is developed and manufactured directly at our company headquarters in Fichtenberg, Swabia, in order to meet the high standards of our KW quality management. As a German manufacturer, it is a matter of course for us to offer a multi-year warranty on our KW coilover suspension kits, which exceed OEM quality and cover over 4,600 applications. It is up to five years when installed by one of our KW specialist dealers. The adaptive KW DDC ECU coilovers with app control are currently available for Audi, BMW, Mercedes-Benz, Porsche, VW and many other vehicles such as the Range Rover Evoque. - retrofittable electronic damper adjustment, combined with the advantages of a KW coilover suspension - with optional app control - Three damping setups: Comfort / Sport / Sport + - Operation via retrofit button or optional app - Create your own setups intuitively via KW DDC app KW DDC button - 1x button, 3x learn more The scope of delivery of the KW DDC ECU coilover kit also includes a KW DDC button. This allows you to select the KW DDC driving modes “Comfort”, “Sport” and “Sport+” directly from the cockpit. The KW DDC button changes the color to fit the KW DDC APP. W-LAN module & app control Optionally available app control for live suspension tuning via iPhone, iPod touch, iPad. Experience top-class innovation and quality “Made in Germany”: the KW DDC (Dynamic Damping Control) coilover suspension with ECU (Electronic Control Unit). The coilover suspension with its electronically adjustable dampers enables intelligent suspension tuning via app control and is already available for numerous vehicles without adaptive standard suspension. This allows you to upgrade your vehicle with adaptive damper control and optionally adapt it to your driving style via the KW DDC app. You do not need any tools or have to work on the dampers yourself. The free KW DDC App in combination with our optionally available W-Lan module is your tool to perform an individual damper tuning live and in real time. Please note the conditions and instructions for this product: - VA + HA height-adjustable (VA coilover struts, HA springs with height adjustment + damper) Technical info: Lowering VA/HA (mm): 10-35/5-25 Version: DDC - ECU Hardness adjustment: Rebound and compression stage Material: Stainless steel Adjustment VA/HA: thread/thread Approval: Parts certificate (§19.3) Compatible vehicles: Manufacturer Model Version Body Fuel Performance Displacement Cylinder Drive BMW 1 Series Coupe (E82) 182, 1C, M-V 10/2006-10/2013 M Coupe Petrol 250 KW 2979 ccm 6 Rear-wheel drive

This brake cooling duct kit is designed to be adapted to the 1M Raze front splitter to provide fresh cooling air directly to the brake discs. Application: Fits 1M Raze front splitter onlyMaterial: FRP or carbonInstallation: bolt-onExpert opinion: Material certificate Compatible vehicles:VehicleVehicle typePowerEngine capacityEngine typeYear of construction BMW 1er Coupe (E82)M250kW / 340hp2979cm³N54 B30 A03.11 - 06.12