In many vehicles, brake cooling is already recommended for medium loads, even off the racetrack.This not only improves braking performance, but can also drastically reduce wear on the friction partners.We use the channeling of the air flow to the center of the brake disc to utilize the turbine effect to cool the disc from the inside. In doing so, we direct the airflow at the disc at a specific angle in order to avoid scattering losses and make maximum efficient use of the available air volume.Thanks to the lightweight construction in combination with powdered aluminum, the component is sufficiently strong and at the same time light and robust. Your vehicle is not slow, that's a fact. However, this speed must be reduced as quickly as possible before cornering and this generates enormous heat. The ball joint of your control arm is extremely close to the hot brake disk and will be affected in the long term. This anchor plate therefore provides additional shielding for the bearing, thereby increasing its durability. Scope of delivery:Anchor plates for the front axle 1x left 1x right with connection for 51 mm air hose(air hose + clamps not included, optionally available). The anchor plate fits plug & play and no additional fastening material is required. The original fixing points and screws can be reused. Suitable for: E90/92/93 M3E82 1 Series M

This brake cooling duct kit is designed to be adapted to the 1M Raze front splitter to provide fresh cooling air directly to the brake discs. Application: Fits 1M Raze front splitter onlyMaterial: FRP or carbonInstallation: bolt-onExpert opinion: Material certificate Compatible vehicles:VehicleVehicle typePowerEngine capacityEngine typeYear of construction BMW 1er Coupe (E82)M250kW / 340hp2979cm³N54 B30 A03.11 - 06.12

In order to transport the air precisely to the brake system, a suitable inlet is essential. The F-series already has factory-fitted inlet ducts in the front bumper, but these end in the middle of the wheel arch. To ensure that the air let in through the inlet ducts of the front bumper is not randomly swirled around in the wheel arch, we have developed an inlet duct that can be fitted with little effort and directs the air precisely to the brakes - i.e. exactly where it is needed. The covers can optionally be fitted on the outside in front of the ventilation grilles as protection against moisture or similar. No fastening tools are required for installation on the front axle. They are fitted in exchange for the original duct support. The duct is based on the OEM duct and therefore uses exactly the same connection points and can be completely removed without leaving any residue. As the inside of the brake disk on the rear axle builds up very high temperatures, we have also developed an air duct here, which guides the air directly into the inside of the rim via a flow channel. Our brake cooling system is plug & play and requires no modifications to the vehicle. Scope of delivery: - 1x set front axle: 2x intake scoop L+R, 6x 3.6mm cable ties for scoop, 2x 4.8mm cable ties for hose holder, 2x hose holder (wheel housing) - 1x rear axle set: 2 rear air ducts L+R, 8x 4.8mm cable ties - Brake cooling hoses + anchor plates Compatible vehicles: BMW 2 Series (F87) Coupé M2 272kW / 370hp Attention: Without approval in the area of the StVZO.

In order to transport the air precisely to the brake system, a suitable inlet is essential. To ensure that the air let in through the inlet ducts of the front bumper is not randomly swirled around in the wheel arch, we have developed an inlet duct that can be fitted with little effort and directs the air precisely to the brakes - i.e. exactly where it is needed. The covers can optionally be fitted on the outside in front of the ventilation grilles as protection against moisture or similar. Our brake cooling system is plug & play and requires no modifications to the vehicle. Scope of delivery: - 4x intake scoop L+R, 2x anchor plate, mounting material, hose Compatible vehicles:- 1er (E81)- 1er (E82) Coupé- 1er (E87)- 1er (E88) Cabrio Attention: Without approval in the area of the StVZO.

In order to transport the air precisely to the brake system, a suitable inlet is essential. To ensure that the air let in through the inlet ducts of the front bumper is not randomly swirled around in the wheel arch, we have developed an inlet duct that can be fitted with little effort and directs the air precisely to the brakes - i.e. exactly where it is needed. The covers can optionally be fitted on the outside in front of the ventilation grilles as protection against moisture or similar. Our brake cooling system is plug & play and requires no modifications to the vehicle. Scope of delivery: - 2x intake scoop L+R Compatible vehicles:- BMW M240i (G42)- BMW M340i (G20/G21)- BMW M440i (G22/G23/G26) Attention: Without approval in the area of the StVZO.

In order to transport the air precisely to the brake system, a suitable inlet is essential. To ensure that the air let in through the inlet ducts of the front bumper is not randomly swirled around in the wheel arch, we have developed an inlet duct that can be fitted with little effort and directs the air precisely to the brakes - i.e. exactly where it is needed. The covers can optionally be fitted on the outside in front of the ventilation grilles as protection against moisture or similar. Our brake cooling system is plug & play and requires no modifications to the vehicle. Scope of delivery: - 2x intake scoop L+R Compatible vehicles:- BMW Z4 (G29)- Toyota Supra MK5 (DB/A90) Attention: Without approval in the area of the StVZO.

Fully synthetic brake fluid based on polyglycol. For all types of racing brake systems (steel, carbon or ceramic) Suitable for car and motorbike Details: Standards: SAE J 1703, ISO 4925, FMVSS 116 DOT 4 Dry boiling point: 328°C Wet boiling point: 205°C Content: - 500ml (0.5L)

The Endless pads are an excellent brake pad for racing and everyday use. The ME22 is the further development of the popular ME20 brake pad. Unlike the MX72 pad, the ME22 has no heat shields.Coefficient of friction 0.36 - 0.42 µOperating temperature 150 - 800 °CSemi-metallic pad For the rear axle. Compatible vehicles:BMW 4-piston BMW (Performance) brake caliper, blue caliper for F-series vehicles, such as M135i M140i F20 F21, M235i M240i F22 F23, 335i 340i F30 F31 F34, 435i 440i F32 F33 F36, M2 F87, M3 F80,M4 F82 F83Alpina models such as the B3Motorsport articles - without STVZO approval.

The Endless pads are an excellent brake pad for racing and everyday use. The ME22 is the further development of the popular ME20 brake pad. In contrast to the MX72 pad, the ME22 has no heat protection plates.Coefficient of friction 0.36 - 0.42 µOperating temperature 150 - 800 °CSemi-metallic pad For the front axle. Compatible vehicles:BMW 4-piston BMW (Performance) brake caliper, blue caliper on F-series vehicles, such as M135i M140i F20 F21, M235i M240i F22 F23, 335i 340i F30 F31 F34, 435i 440i F32 F33 F36, M2 F87, M3 F80,M4 F82 F83Alpina models such as the B3 Motorsport articles - without STVZO approval.

The Endless pads are an excellent brake pad for racing and everyday use. The MX87 is the further development of the MX72 and not only builds up friction with the disc faster, but is also more heat-resistant. Temperature range from 30-700CLow brake disc wearamazing longevity of the padReduction of heat cracksimproved response behaviourCoefficient of friction of 0.38-0.46 By far the greatest speciality, however, is the balancing act between suitability for everyday use and use on trackdays:This means that this rubber is suitable in every situation, whether on long trackdays, or in everyday use.However, if the vehicle is mainly used on the track, we recommend the N39S. For the front axle. Compatible vehicles:BMW 4-piston BMW (Performance) brake caliper, blue caliper on F-series vehicles, such as. M135i M140i F20 F21, M235i M240i F22 F23, 335i 340i F30 F31 F34, 435i 440i F32 F33 F36, M2 F87, M3 F80,M4 F82 F83Alpina models such as the B3Motorsport articles - without STVZO approval.

The Endless pads are an excellent brake pad for everyday road use with sporadic track days. Despite reduced dust and noise emissions, the MX72 impresses with excellent deceleration values even in the high temperature range. In contrast to the ME20 and ME22 pads, the MX72 has heat protection plates.Coefficient of friction 0.37 - 0.47 µOperating temperature 50 - 700 °CSemi-metallic pad For the rear axle. Compatible vehicles:BMW 4-piston BMW (Performance) brake caliper, blue caliper for F-series vehicles, e.g. M135i M140i F20 F21, M235i M240i F22 F23, 335i 340i F30 F31 F34, 435i 440i F32 F33 F36, M2 F87, M3 F80,M4 F82 F83Alpina models such as the B3Motorsport articles - without STVZO approval.

The Endless pads are an excellent brake pad for everyday road use with sporadic track days. Despite reduced dust and noise emissions, the MX72 brake pad impresses with excellent deceleration values even in the high temperature range. In contrast to the ME20 and ME22 pads, the MX72 has heat protection plates.Coefficient of friction 0.37 - 0.47 µOperating temperature 50 - 700 °CSemi-metallic pad For the front axle. Compatible vehicles:BMW M2 F87 Competition with large gray 6-piston sports brakeBMW M2 F87 CSBMW M5 F10 Motorsport article - without STVZO approval.

The Endless pads are an excellent brake pad for everyday road use with sporadic track days. Despite reduced dust and noise emissions, the MX72-Plus brake pad impresses with excellent deceleration values, even in the high temperature range. In contrast to the ME20 and ME22 pads, the MX72-Plus has heat protection plates.Coefficient of friction 0.39 - 0.47 µOperating temperature 50 - 750 °CSemi-metallic pad For the rear axle. Compatible vehicles:BMW M2 F87 Competition with large gray 6-piston sports brake Motorsport article - without STVZO approval.

With the AP-Racing Big Brake Kit, we offer a high-performance solution especially for track days and for race track drivers. The friction rings are mounted floating on the high-strength, milled aluminium pots. The advantages of this are, on the one hand, the lower weight and, on the other, the fact that the friction rings can be replaced cost-effectively when they wear out. The AP-Racing calipers are racing calipers without dust boots, which are only recommended for use on the racetrack (regular cleaning of the calipers is necessary in normal road traffic). Details and scope of delivery:- Big Brake Kit for the front/rear axle, consisting of AP Racing calipers and J-Hook brake discs in 378×34mm- AP Racing 6-piston brake caliper- Brake discs 378×34mm, J-Hook- CNC milled brake caliper adapter incl. material certificate- Braided steel brake lines- incl. brake padsAluminium pots and floating mounting Compatible vehicles:- BMW F87 M2 incl. Competition/CS- BMW F8x M3/M4 incl. Competition NOTES:If we do not expressly refer to a parts certificate or general operating licence (ABE) in the product text, this is a motorsport article that is not approved in the German Road Traffic Regulations (StVZO) and therefore the operating licence expires if no registration is made in accordance with § 21 StVO!This brake system can only be registered by us after special tests. Please note that vehicle spare parts should only be installed by a qualified specialist workshop in order to ensure that they function properly and that the vehicle is roadworthy.

MOVIT DDE steel brake system 342x28mm (4 piston calliper) for the rear axle, from 18 inch rims upwardsApplication-focussed development is the cornerstone of this high-performance brake system. The required balance of weight, performance and durability is optimally combined. The uncompromising selection of materials in production results in a highly unique product that meets the diverse requirements of extreme automotive applications. The most important features of the MOVIT brake system are- The progressive staggering of the piston diameters, matched to the vehicle, so that precisely parallel contact pressure between the pad and the disc is guaranteed. This enables even wear of the brake pads and ensures even heat transfer and a reduced system temperature.- Very good heat dissipation due to the open design of the brake pad contour.- Calipers manufactured from high-strength, highly tempered aircraft aluminium 7075 with high-quality material properties (stiffer components, more homogeneous structure), hard anodised and coated with a triple layer of paint.- Optimised stability due to the length of the callipers- Larger brake disc diameter and thickness, more cross holes (each pre-cast hole is re-drilled and countersunk, which has a favourable effect on the flow).- The brake discs are thermally tempered.- The optimised DDE ventilation system (double directional evolvent system) of the brake disc has an 80% larger surface area compared to other brake discs, the temperature of the brake disc is significantly reduced and therefore also the wear.- Long service life of the wearing parts, excellent response behaviour, steel flex lines ensure consistent performance.- Optimally matched brake pads ensure fading resistance, a long service life and reduced wear on spare parts Attention: The conversion means that only rims with at least 18 inches can be fitted! The chassis number of the vehicle on which the brakes are fitted is required for the parts certificate. MOVIT sports brake callipers, 4-piston- Milled from high-strength aircraft aluminium 7075- Two-piece- Use of maximum disc size due to long design- Significantly improved rigidity and extended contact surface of the pad- Uniform heat transfer- Reduced system temperature- Low, even pad wear- Progressive piston staggering- Crown system for fixing the brake hose- RAPAD-X system for quick brake pad replacement without removing the caliper from the bracket- Open brake pad track for optimised cooling- Maximum stability- Maximum braking force MOVIT sports brake discs, 342x28mm, 2-piece- Highly efficient DDE cooling system- Perforated for optimum response behaviour even on wet roads- Maximum fading resistance- Special alloy for high thermal conductivity MOVIT comfort brake pads- Enlarged friction surface- Lower system temperature- Uniform heat transfer- Longer service life Scope of delivery:2x MOVIT brake caliper (left/right)2x MOVIT brake disc (left/right)2x vehicle-specific brake caliper adapter1x set of comfort brake pads2x steel flex lines1x handbrake calliper (depending on selected option)1x assembly material1x installation instructions and running-in instructions1x parts certificate Compatible vehicles:BMW 1 Series (F20/F21) (also M)BMW 3 Series (E90)BMW 3 Series (E46) M3BMW 3 Series (E46) M3 CSLBMW 3 Series (E92) M3

MOVIT DDE steel brake system 380x32mm (4 piston calliper) for the rear axle, from 19 inch rims upwardsApplication-focussed development is the cornerstone of this high-performance brake system. The required balance of weight, performance and durability is optimally combined. The uncompromising selection of materials in production results in a highly unique product that fulfils the diverse requirements of extreme automotive applications. The most important features of the MOVIT brake system are- The progressive staggering of the piston diameters, matched to the vehicle, so that precisely parallel contact pressure between the pad and the disc is guaranteed. This enables even wear of the brake pads and ensures even heat transfer and a reduced system temperature.- Very good heat dissipation due to the open design of the brake pad contour.- Calipers manufactured from high-strength, highly tempered aircraft aluminium 7075 with high-quality material properties (stiffer components, more homogeneous structure), hard anodised and coated with a triple layer of paint.- Optimised stability due to the length of the callipers- Larger brake disc diameter and thickness, more cross holes (each pre-cast hole is re-drilled and countersunk, which has a favourable effect on the flow).- The brake discs are thermally tempered.- The optimised DDE ventilation system (double directional evolvent system) of the brake disc has an 80% larger surface area compared to other brake discs, the temperature of the brake disc is significantly reduced and therefore also the wear.- Long service life of the wearing parts, excellent response behaviour, steel flex lines ensure consistent performance.- Optimally matched brake pads ensure fading resistance, a long service life and reduced wear on spare parts Attention: The conversion means that only rims with at least 19 inches can be fitted! The chassis number of the vehicle on which the brakes are fitted is required for the parts certificate. MOVIT sports brake callipers, 4-piston- Milled from high-strength aircraft aluminium 7075- Two-piece- Use of maximum disc size due to long design- Significantly improved rigidity and extended contact surface of the pad- Uniform heat transfer- Reduced system temperature- Low, even pad wear- Progressive piston staggering- Crown system for fixing the brake hose- RAPAD-X system for quick brake pad replacement without removing the caliper from the bracket- Open brake pad track for optimised cooling- Maximum stability- Maximum braking force MOVIT sports brake discs, 380x32mm, 2-piece- Highly efficient DDE cooling system- Perforated for optimum response behaviour even on wet roads- Highest fading resistance- Special alloy for high thermal conductivity MOVIT comfort brake pads- Enlarged friction surface- Lower system temperature- Uniform heat transfer- Longer service life Scope of delivery:2x MOVIT brake caliper (left/right)2x MOVIT brake disc (left/right)2x vehicle-specific brake caliper adapter1x comfort brake pads2x steel flex lines1x handbrake calliper (depending on selected option)1x installation material1x installation instructions and running-in instructions1x parts certificate Compatible vehicles:BMW 2 Series (F87) Coupé M2 272kW / 370PS / 2979cm³ / N55BMW 3 Series (E92) Coupé M3 309kW / 420PS / 3999cm³ / S65BMW 4 Series (F82) Coupé M4 317kW / 431PS / 2979cm³ / S55

MOVIT DDE steel brake system 342x28mm (4 piston calliper) for the front axle, from 18 inch rims upwardsApplication-focussed development is the cornerstone of this high-performance brake system. The required balance of weight, performance and durability is optimally combined. The uncompromising selection of materials in production results in a highly unique product that meets the diverse requirements of extreme automotive applications. The most important features of the MOVIT brake system are- The progressive staggering of the piston diameters, matched to the vehicle, so that precisely parallel contact pressure between the pad and the disc is guaranteed. This enables even wear of the brake pads and ensures even heat transfer and a reduced system temperature.- Very good heat dissipation due to the open design of the brake pad contour.- Calipers manufactured from high-strength, highly tempered aircraft aluminium 7075 with high-quality material properties (stiffer components, more homogeneous structure), hard anodised and coated with a triple layer of paint.- Optimised stability due to the length of the callipers- Larger brake disc diameter and thickness, more cross holes (each pre-cast hole is re-drilled and countersunk, which has a favourable effect on the flow).- The brake discs are thermally tempered.- The optimised DDE ventilation system (double directional evolvent system) of the brake disc has an 80% larger surface area compared to other brake discs, the temperature of the brake disc is significantly reduced and therefore also the wear.- Long service life of the wearing parts, excellent response behaviour, steel flex lines ensure consistent performance.- Optimally matched brake pads ensure fading resistance, a long service life and reduced wear on spare parts Attention: The conversion means that only rims with at least 18 inches can be fitted! The chassis number of the vehicle on which the brakes are fitted is required for the parts certificate. MOVIT sports brake callipers, 4s6, 4-piston- Milled from high-strength aircraft aluminium 7075- Two-piece- Use of maximum disc size due to long design- Significantly improved rigidity and extended contact surface of the pad- Uniform heat transfer- Reduced system temperature- Low, even pad wear- Progressive piston staggering- Crown system for fixing the brake hose- RAPAD-X system for quick brake pad replacement without removing the caliper from the bracket- Open brake pad track for optimised cooling- Maximum stability- Maximum braking force MOVIT sports brake discs, 342x28mm, 2-piece- Highly efficient DDE cooling system- Perforated for optimum response behaviour even on wet roads- Maximum fading resistance- Special alloy for high thermal conductivity MOVIT brake pads, comfort BE-4s6- Enlarged friction surface- Lower system temperature- Uniform heat transfer- Longer service life Scope of delivery:2x MOVIT brake caliper (left/right)2x MOVIT brake disc (left/right)2x vehicle-specific brake caliper adapter1x set of comfort brake pads2x steel flex lines1x assembly material1x installation instructions and running-in instructions1x parts certificate Compatible vehicles:Audi S1 8XVW Polo 6R WRC

MOVIT DDE steel brake system 342x34mm (4 piston calliper) for the front axle, from 18 inch rims upwardsApplication-focussed development is the cornerstone of this high-performance brake system. The required balance of weight, performance and durability is optimally combined. The uncompromising selection of materials in production results in a highly unique product that meets the diverse requirements of extreme automotive applications. The most important features of the MOVIT brake system are- The progressive staggering of the piston diameters, matched to the vehicle, so that precisely parallel contact pressure between the pad and the disc is guaranteed. This enables even wear of the brake pads and ensures even heat transfer and a reduced system temperature.- Very good heat dissipation due to the open design of the brake pad contour.- Calipers manufactured from high-strength, highly tempered aircraft aluminium 7075 with high-quality material properties (stiffer components, more homogeneous structure), hard anodised and coated with a triple layer of paint.- Optimised stability due to the length of the callipers- Larger brake disc diameter and thickness, more cross holes (each pre-cast hole is re-drilled and countersunk, which has a favourable effect on the flow).- The brake discs are thermally tempered.- The optimised DDE ventilation system (double directional evolvent system) of the brake disc has an 80% larger surface area compared to other brake discs, the temperature of the brake disc is significantly reduced and therefore also the wear.- Long service life of the wearing parts, excellent response behaviour, steel flex lines ensure consistent performance.- Optimally matched brake pads ensure fading resistance, a long service life and reduced wear on spare parts Attention: The conversion means that only rims with at least 18 inches can be fitted! The chassis number of the vehicle on which the brakes are fitted is required for the parts certificate. MOVIT sports brake callipers, 4s3, 4-piston- Milled from high-strength aircraft aluminium 7075- Two-piece- Use of maximum disc size due to long design- Significantly improved rigidity and extended contact surface of the pad- Uniform heat transfer- Reduced system temperature- Low, even pad wear- Progressive piston staggering- Crown system for fixing the brake hose- RAPAD-X system for quick brake pad replacement without removing the caliper from the bracket- Open brake pad track for optimised cooling- Maximum stability- Maximum braking force MOVIT sports brake discs, 342x34mm, 2-piece- Highly efficient DDE cooling system- Perforated for optimum response behaviour even on wet roads- Maximum fading resistance- Special alloy for high thermal conductivity MOVIT brake pads, comfort BE-4s3- Enlarged friction surface- Lower system temperature- Uniform heat transfer- Longer service life Scope of delivery:2x MOVIT brake caliper (left/right)2x MOVIT brake disc (left/right)2x vehicle-specific brake caliper adapter1x set of comfort brake pads2x steel flex lines1x assembly material1x installation instructions and running-in instructions1x parts certificate Compatible vehicles:Audi A4 / S4 B7 / 8EAudi S3 8VBMW 1 Series E81 / E82 / E87 / E88BMW 3 Series E36BMW 3 Series E46BMW 3 Series E90BMW M3 E46BMW M3 E46 CSL

MOVIT DDE steel brake system 342x34mm (6 piston calliper) for the front axle, from 18 inch rims upwardsApplication-focussed development is the cornerstone of this high-performance brake system. The required balance of weight, performance and durability is optimally combined. The uncompromising selection of materials in production results in a highly unique product that meets the diverse requirements of extreme automotive applications. The most important features of the MOVIT brake system are- The progressive staggering of the piston diameters, matched to the vehicle, so that precisely parallel contact pressure between the pad and the disc is guaranteed. This enables even wear of the brake pads and ensures even heat transfer and a reduced system temperature.- Very good heat dissipation due to the open design of the brake pad contour.- Calipers manufactured from high-strength, highly tempered aircraft aluminium 7075 with high-quality material properties (stiffer components, more homogeneous structure), hard anodised and coated with a triple layer of paint.- Optimised stability due to the length of the callipers- Larger brake disc diameter and thickness, more cross holes (each pre-cast hole is re-drilled and countersunk, which has a favourable effect on the flow).- The brake discs are thermally tempered.- The optimised DDE ventilation system (double directional evolvent system) of the brake disc has an 80% larger surface area compared to other brake discs, the temperature of the brake disc is significantly reduced and therefore also the wear.- Long service life of the wearing parts, excellent response behaviour, steel flex lines ensure consistent performance.- Optimally matched brake pads ensure fading resistance, a long service life and reduced wear on spare parts Attention: The conversion means that only rims with at least 18 inches can be fitted! The chassis number of the vehicle on which the brakes are fitted is required for the parts certificate. MOVIT sports brake callipers, 6-piston- Milled from high-strength aircraft aluminium 7075- Two-piece- Use of maximum disc size due to long design- Significantly improved rigidity and extended contact surface of the pad- Uniform heat transfer- Reduced system temperature- Low, even pad wear- Progressive piston staggering- Crown system for fixing the brake hose- RAPAD-X system for quick brake pad replacement without removing the caliper from the bracket- Open brake pad track for optimised cooling- Maximum stability- Maximum braking force MOVIT sports brake discs, 342x34mm, 2-piece- Highly efficient DDE cooling system- Perforated for optimum response behaviour even on wet roads- Maximum fading resistance- Special alloy for high thermal conductivity MOVIT comfort brake pads- Enlarged friction surface- Lower system temperature- Uniform heat transfer- Longer service life Scope of delivery:2x MOVIT brake caliper (left/right)2x MOVIT brake disc (left/right)2x vehicle-specific brake caliper adapter1x set of comfort brake pads2x steel flex lines1x assembly material1x installation instructions and running-in instructions1x parts certificate Compatible vehicles:Audi A4 / S4 8K / B8Audi A5 / S5 8TVW Beetle 5CVW Golf IV 4motionVW Golf VII GTI / GTD 57 series pistonsVW Golf VII GTI / GTD 57 series pistonsVW GOLF VII GTI Clubsport / Performance 60 series pistonsVW T5 / T6 Multivan

MOVIT DDE steel brake system 370x35mm (6 piston calliper) for the front axle, from 18 inch rims upwardsApplication-focussed development is the cornerstone of this high-performance brake system. The required balance of weight, performance and durability is optimally combined. The uncompromising selection of materials in production results in a highly unique product that meets the diverse requirements of extreme automotive applications. The most important features of the MOVIT brake system are- The progressive staggering of the piston diameters, matched to the vehicle, so that precisely parallel contact pressure between the pad and the disc is guaranteed. This enables even wear of the brake pads and ensures even heat transfer and a reduced system temperature.- Very good heat dissipation due to the open design of the brake pad contour.- Calipers manufactured from high-strength, highly tempered aircraft aluminium 7075 with high-quality material properties (stiffer components, more homogeneous structure), hard anodised and coated with a triple paint finish.- Optimised stability due to the length of the callipers- Larger brake disc diameter and thickness, more cross holes (each pre-cast hole is re-drilled and countersunk, which has a favourable effect on the flow).- The brake discs are thermally tempered.- The optimised DDE ventilation system (double directional evolvent system) of the brake disc has an 80% larger surface area compared to other brake discs, the temperature of the brake disc is significantly reduced and therefore also the wear.- Long service life of the wearing parts, excellent response behaviour, steel flex lines ensure consistent performance.- Optimally matched brake pads ensure fading resistance, a long service life and reduced wear on spare parts Attention: The conversion means that only rims with at least 18 inches can be fitted! The chassis number of the vehicle on which the brakes are fitted is required for the parts certificate. MOVIT sports brake callipers, 6s5, 6-piston- Milled from high-strength aircraft aluminium 7075- Two-piece- Use of maximum disc size due to long design- Significantly improved rigidity and extended contact surface of the pad- Uniform heat transfer- Reduced system temperature- Low, even pad wear- Progressive piston staggering- Crown system for fixing the brake hose- RAPAD-X system for quick brake pad replacement without removing the caliper from the bracket- Open brake pad track for optimised cooling- Maximum stability- Maximum braking force MOVIT sports brake discs, 370x35mm, 2-piece- Highly efficient DDE cooling system- Perforated for optimum response behaviour even on wet roads- Maximum fading resistance- Special alloy for high thermal conductivity MOVIT comfort brake pads, BE-6s1- Enlarged friction surface- Lower system temperature- Uniform heat transfer- Longer service life Scope of delivery:2x MOVIT brake caliper (left/right)2x MOVIT brake disc (left/right)2x vehicle-specific brake caliper adapter1x set of comfort brake pads2x steel flex lines1x assembly material1x installation instructions and running-in instructions1x parts certificate Compatible vehicles:BMW 1 Series F20 / F21 (also M)Ford Focus RS CB4 / MKIIAudi RS3 8PAudi RS4 B5Audi S4 Type 8D / B5BMW M3 E46BMW M3 E46 CSLBMW M3 E92Ford Mustang V Shelby GT 500Mercedes Benz W639 Vito / VianoVolvo XC90 1st gen. from 2011 onwardsVW Golf VII GTI / GTD 57 series pistonsVW Golf VII GTI / GTD 57 series pistonsVW GOLF VII GTI Clubsport / Performance 60 series pistonsVW Golf VII RVW Golf VII RVW T5 / T6 Multivan

MOVIT DDE steel brake system 380x32mm (6 piston calliper) for the front axle, from 19 inch rims upwardsApplication-focussed development is the cornerstone of this high-performance brake system. The required balance of weight, performance and durability is optimally combined. The uncompromising selection of materials in production results in a highly unique product that meets the diverse requirements of extreme automotive applications. The most important features of the MOVIT brake system are- The progressive staggering of the piston diameters, matched to the vehicle, so that precisely parallel contact pressure between the pad and the disc is guaranteed. This enables even wear of the brake pads and ensures even heat transfer and a reduced system temperature.- Very good heat dissipation due to the open design of the brake pad contour.- Calipers manufactured from high-strength, highly tempered aircraft aluminium 7075 with high-quality material properties (stiffer components, more homogeneous structure), hard anodised and coated with a triple layer of paint.- Optimised stability due to the length of the callipers- Larger brake disc diameter and thickness, more cross holes (each pre-cast hole is re-drilled and countersunk, which has a favourable effect on the flow).- The brake discs are thermally tempered.- The optimised DDE ventilation system (double directional evolvent system) of the brake disc has an 80% larger surface area compared to other brake discs, the temperature of the brake disc is significantly reduced and therefore also the wear.- Long service life of the wearing parts, excellent response behaviour, steel flex lines ensure consistent performance.- Optimally matched brake pads ensure fading resistance, a long service life and reduced wear on spare parts Attention: The conversion means that only rims with at least 19 inches can be fitted! The chassis number of the vehicle on which the brakes are fitted is required for the parts certificate. MOVIT sports brake callipers, 6-piston- Milled from high-strength aircraft aluminium 7075- Two-piece- Use of maximum disc size due to long design- Significantly improved rigidity and extended contact surface of the pad- Uniform heat transfer- Reduced system temperature- Low, even pad wear- Progressive piston staggering- Crown system for fixing the brake hose- RAPAD-X system for quick brake pad replacement without removing the caliper from the bracket- Open brake pad track for optimised cooling- Maximum stability- Maximum braking force MOVIT sports brake discs, 380x32mm, 2-piece- Highly efficient DDE cooling system- Perforated for optimum response behaviour even on wet roads- Highest fading resistance- Special alloy for high thermal conductivity MOVIT comfort brake pads- Enlarged friction surface- Lower system temperature- Uniform heat transfer- Longer service life Scope of delivery:2x MOVIT brake caliper (left/right)2x MOVIT brake disc (left/right)2x vehicle-specific brake caliper adapter1x set of comfort brake pads2x steel flex lines1x assembly material1x installation instructions and running-in instructions1x parts certificate Compatible vehicles:BMW 5 Series (E60) M5 373kW / 507PS / 4999cm³ / S85BMW 6 Series (E63) M6 373kW / 507PS / 4999cm³ / S85

MOVIT DDE steel brake system 380x36mm (6 piston calliper) for the front axle, from 19 inch rims upwardsApplication-focussed development is the cornerstone of this high-performance brake system. The required balance of weight, performance and durability is optimally combined. The uncompromising selection of materials in production results in a highly unique product that meets the diverse requirements of extreme automotive applications. The most important features of the MOVIT brake system are- The progressive staggering of the piston diameters, matched to the vehicle, so that precisely parallel contact pressure between the pad and the disc is guaranteed. This enables even wear of the brake pads and ensures even heat transfer and a reduced system temperature.- Very good heat dissipation due to the open design of the brake pad contour.- Calipers manufactured from high-strength, highly tempered aircraft aluminium 7075 with high-quality material properties (stiffer components, more homogeneous structure), hard anodised and coated with a triple layer of paint.- Optimised stability due to the length of the callipers- Larger brake disc diameter and thickness, more cross holes (each pre-cast hole is re-drilled and countersunk, which has a favourable effect on the flow).- The brake discs are thermally tempered.- The optimised DDE ventilation system (double directional evolvent system) of the brake disc has an 80% larger surface area compared to other brake discs, the temperature of the brake disc is significantly reduced and therefore also the wear.- Long service life of the wearing parts, excellent response behaviour, steel flex lines ensure consistent performance.- Optimally matched brake pads ensure fading resistance, a long service life and reduced wear on spare parts Attention: The conversion means that only rims with at least 19 inches can be fitted! The chassis number of the vehicle on which the brakes are fitted is required for the parts certificate. MOVIT sports brake callipers, 6-piston- Milled from high-strength aircraft aluminium 7075- Two-piece- Use of maximum disc size due to long design- Significantly improved rigidity and extended contact surface of the pad- Uniform heat transfer- Reduced system temperature- Low, even pad wear- Progressive piston staggering- Crown system for fixing the brake hose- RAPAD-X system for quick brake pad replacement without removing the caliper from the bracket- Open brake pad track for optimised cooling- Maximum stability- Maximum braking force MOVIT sports brake discs, 380x36mm, 2-piece- Highly efficient DDE cooling system- Perforated for optimum response behaviour even on wet roads- Maximum fading resistance- Special alloy for high thermal conductivity MOVIT comfort brake pads- Enlarged friction surface- Lower system temperature- Uniform heat transfer- Longer service life Scope of delivery:2x MOVIT brake caliper (left/right)2x MOVIT brake disc (left/right)2x vehicle-specific brake caliper adapter2x sports brake pads2x steel flex lines1x assembly material1x installation instructions and running-in instructions1x parts certificate Compatible vehicles:Audi A3 (8VA, 8VF) RS3 quattro 270kW / 367PS / 2480cm³Audi A3 (8VA, 8VF) RS3 quattro 294kW / 400PS / 2480cm³

MOVIT DDE steel brake system 392x36mm (6 piston calliper) for the front axle, from 20 inch rims upwardsApplication-focussed development is the cornerstone of this high-performance brake system. The required balance of weight, performance and durability is optimally combined. The uncompromising selection of materials in production results in a highly unique product that meets the diverse requirements of extreme automotive applications. The most important features of the MOVIT brake system are- The progressive staggering of the piston diameters, matched to the vehicle, so that precisely parallel contact pressure between the pad and the disc is guaranteed. This enables even wear of the brake pads and ensures even heat transfer and a reduced system temperature.- Very good heat dissipation due to the open design of the brake pad contour.- Calipers manufactured from high-strength, highly tempered aircraft aluminium 7075 with high-quality material properties (stiffer components, more homogeneous structure), hard anodised and coated with a triple layer of paint.- Optimised stability due to the length of the callipers- Larger brake disc diameter and thickness, more cross holes (each pre-cast hole is re-drilled and countersunk, which has a favourable effect on the flow).- The brake discs are thermally tempered.- The optimised DDE ventilation system (double directional evolvent system) of the brake disc has an 80% larger surface area compared to other brake discs, the temperature of the brake disc is significantly reduced and therefore also the wear.- Long service life of the wearing parts, excellent response behaviour, steel flex lines ensure consistent performance.- Optimally matched brake pads ensure fading resistance, a long service life and reduced wear on spare parts Attention: The conversion means that only rims with at least 20 inches can be fitted! The chassis number of the vehicle on which the brakes are fitted is required for the parts certificate. MOVIT sports brake callipers, 6-piston- Milled from high-strength aircraft aluminium 7075- Two-piece- Use of maximum disc size due to long design- Significantly improved rigidity and extended contact surface of the pad- Uniform heat transfer- Reduced system temperature- Low, even pad wear- Progressive piston staggering- Crown system for fixing the brake hose- RAPAD-X system for quick brake pad replacement without removing the caliper from the bracket- Open brake pad track for optimised cooling- Maximum stability- Maximum braking force MOVIT sports brake discs, 392x36mm, 2-piece- Highly efficient DDE cooling system- Perforated for optimum response behaviour even on wet roads- Maximum fading resistance- Special alloy for high thermal conductivity MOVIT comfort brake pads- Enlarged friction surface- Lower system temperature- Uniform heat transfer- Longer service life Scope of delivery:2x MOVIT brake caliper (left/right)2x MOVIT brake disc (left/right)2x vehicle-specific brake caliper adapter2x sports brake pads2x steel flex lines1x assembly material1x installation instructions and running-in instructions1x parts certificate Compatible vehicles:Audi A3 (8VA, 8VF) RS3 quattro 270kW / 367PS / 2480cm³Audi A3 (8VA, 8VF) RS3 quattro 294kW / 400PS / 2480cm³

MOVIT DDE steel brake system 396x36mm (6 piston calliper) for the front axle, from 20 inch rims upwardsApplication-focussed development is the cornerstone of this high-performance brake system. The required balance of weight, performance and durability is optimally combined. The uncompromising selection of materials in production results in a highly unique product that meets the diverse requirements of extreme automotive applications. The most important features of the MOVIT brake system are- The progressive staggering of the piston diameters, matched to the vehicle, so that precisely parallel contact pressure between the pad and the disc is guaranteed. This enables even wear of the brake pads and ensures even heat transfer and a reduced system temperature.- Very good heat dissipation due to the open design of the brake pad contour.- Calipers manufactured from high-strength, highly tempered aircraft aluminium 7075 with high-quality material properties (stiffer components, more homogeneous structure), hard anodised and coated with a triple layer of paint.- Optimised stability due to the length of the callipers- Larger brake disc diameter and thickness, more cross holes (each pre-cast hole is re-drilled and countersunk, which has a favourable effect on the flow).- The brake discs are thermally tempered.- The optimised DDE ventilation system (double directional evolvent system) of the brake disc has an 80% larger surface area compared to other brake discs, the temperature of the brake disc is significantly reduced and therefore also the wear.- Long service life of the wearing parts, excellent response behaviour, steel flex lines ensure consistent performance.- Optimally matched brake pads ensure fading resistance, a long service life and reduced wear on spare parts Attention: The conversion means that only rims with at least 20 inches can be fitted! The chassis number of the vehicle on which the brakes are fitted is required for the parts certificate. MOVIT sports brake callipers, 6s1, 6-piston- Milled from high-strength aircraft aluminium 7075- Two-piece- Use of maximum disc size due to long design- Significantly improved rigidity and extended contact surface of the pad- Uniform heat transfer- Reduced system temperature- Low, even pad wear- Progressive piston staggering- Crown system for fixing the brake hose- RAPAD-X system for quick brake pad replacement without removing the caliper from the bracket- Open brake pad track for optimised cooling- Maximum stability- Maximum braking force MOVIT sports brake discs, 396x36mm, 2-piece- Highly efficient DDE cooling system- Perforated for optimum response behaviour even on wet roads- Maximum fading resistance- Special alloy for high thermal conductivity MOVIT comfort brake pads, BE-6s1- Enlarged friction surface- Lower system temperature- Uniform heat transfer- Longer service life Scope of delivery:2x MOVIT brake caliper (left/right)2x MOVIT brake disc (left/right)2x vehicle-specific brake caliper adapter1x set of comfort brake pads2x steel flex lines1x assembly material1x installation instructions and running-in instructions1x parts certificate Compatible vehicles:Audi R8 type 420 -2018Audi S6 Type 4FBMW M2 F87BMW M3 E92BMW M4 F82BMW X5 E70Ford Mustang VI 2016- 2.3l EcoboostFord Mustang VI 5.0 V8 GT 2015-Mercedes Benz W906 Sprinter 3t & 3.5t

A powerful brake is one of the most important components in motorsport. With these upgrade kits, the necessary balance of performance, weight and durability has been perfectly combined through the uncompromising selection of materials, so that this product can meet the high demands of extreme automotive applications. To achieve this, MOV'IT has increased the diameter and thickness of the brake discs and used more cross holes. Each pre-cast hole is re-drilled and countersunk to achieve a more favourable flow. The brake disc's optimised DDE ventilation system has an 80% larger surface area compared to other brake discs, resulting in a significant reduction in temperature and wear.Without parts certificate Attention: The conversion means that only rims with at least 19 inches can be fitted! Features: - Upgrade kit front axle, 370mm, 2-piece disc, perforated - Without parts certificate Scope of delivery: - 2x brake disc perforated left/right incl. brake pot - 1x mounting material - 1x installation instructions and running-in instructions Compatible vehicles:Audi R8 (422, 423) 4.2 FSI quattro 309kW / 420PS / 4163cm³ (until 31/08/2009)Audi A4 B7 (8E) RS4 quattro 309kW / 420PS / 4163cm³Audi A6 C5 (4B) RS6 quattro 331kW / 450PS / 4172cm³Audi A6 C5 (4B) RS6 quattro plus 353kW / 480PS / 4172cm³ Notes:When installing the upgrade kit, we always recommend replacing the brake pads, as the use of used pads on new brake discs is not recommended.When installed in our factory, the conversion is carried out exclusively with new brake pads!

A powerful brake is one of the most important components in motorsport. With these upgrade kits, the necessary balance of performance, weight and durability has been perfectly combined through the uncompromising selection of materials, so that this product can meet the high demands of extreme automotive applications. To achieve this, MOV'IT has increased the diameter and thickness of the brake discs and used more cross holes. Each pre-cast hole is re-drilled and countersunk to achieve a more favourable flow. The brake disc's optimised DDE ventilation system has an 80% larger surface area compared to other brake discs, resulting in a significant reduction in temperature and wear. Attention: The conversion means that only rims with at least 19 inches can be fitted! The chassis number of the vehicle on which the brakes are fitted is required for the parts certificate. Bundle Street 1: - Upgrade kit front axle, 380mm, 2-piece disc, perforated - incl. parts certificate Bundle Street 2 (+ sports brake pads): - Upgrade kit front axle, 380mm, 2-piece disc, perforated - 4S4 Sport brake pads - incl. parts certificate Street 3 bundle (+ sports brake pads + steel flex lines): - Upgrade kit front axle, 380mm, 2-piece disc, perforated - 4S4 Sport brake pads - Steel flex lines for front and rear axle - incl. parts certificate Details:MOVIT steel brake discs, 2-piece- Highly efficient DDE cooling system- Maximum fading protection- Double, directional ventilation- Perforated for optimum response behaviour even on wet roads- Special alloy for high thermal conductivityMOVIT sports brake pads, front axle- For the original brake caliper- Optimally compatible with MOVIT brake discs- Enlarged friction surface- Even heat transfer- Longer service life- With road approval- Low noise development- Lower system temperature for the perfect friction coefficientMOVIT steel flex lines, front and rear axle- Better response behaviour of the brake system- Durable quality (does not become porous and therefore does not leak)- Brake line does not expand under pressure- Harder and more constant pressure point- Improved modulation Scope of delivery: - 2x brake disc perforated left/right incl. brake pot - 1x mounting material - 1x installation instructions and running-in instructions - 1x parts certificate - 2x sports brake pad (only bundle 2+3) - 2x steel flex lines VA + HA (only bundle 3) Compatible vehicles:Audi A3 (8P) RS3 quattro 250kW / 340PS / 2480cm³Audi TT (8J) TTRS quattro 250kW / 340PS / 2480cm³Audi TT (8J) TTRS quattro plus 265kW / 360PS / 2480cm³ Notes:When installing the upgrade kit, we always recommend replacing the brake pads, as the use of used pads on new brake discs is not recommended.When installed in our factory, the conversion is carried out exclusively with new brake pads!

A powerful brake is one of the most important components in motorsport. With these upgrade kits, the necessary balance of performance, weight and durability has been perfectly combined through the uncompromising selection of materials, so that this product can meet the high demands of extreme automotive applications. To achieve this, MOV'IT has increased the diameter and thickness of the brake discs and used more cross holes. Each pre-cast hole is re-drilled and countersunk to achieve a more favourable flow. The brake disc's optimised DDE ventilation system has an 80% larger surface area compared to other brake discs, resulting in a significant reduction in temperature and wear. Attention: The conversion means that only rims with at least 19 inches can be fitted!Please note that this upgrade kit for the Seat Leon Cupra is only compatible with the caliper of the performance brake system. As the original caliper is retained with this kit, it is essential that the performance caliper is already fitted. The chassis number of the vehicle on which the brakes are fitted is required to create the parts certificate. Bundle Street 1: - Upgrade kit front axle, 380mm, 2-piece disc, perforated - incl. parts certificate Bundle Street 2 (+ sports brake pads): - Upgrade kit front axle, 380mm, 2-piece disc, perforated - 4S4 Sport brake pads - incl. parts certificate Street 3 bundle (+ sports brake pads + steel flex lines): - Upgrade kit front axle, 380mm, 2-piece disc, perforated - 4S4 Sport brake pads - Steel flex lines for front and rear axle - incl. parts certificate Details:MOVIT steel brake discs, 2-piece- Highly efficient DDE cooling system- Maximum fading protection- Double, directional ventilation- Perforated for optimum response behaviour even on wet roads- Special alloy for high thermal conductivityMOVIT sports brake pads, front axle- For the original brake caliper- Optimally compatible with MOVIT brake discs- Enlarged friction surface- Even heat transfer- Longer service life- With road approval- Low noise development- Lower system temperature for the perfect friction coefficientMOVIT steel flex lines, front and rear axle- Better response behaviour of the brake system- Durable quality (does not become porous and therefore does not leak)- Brake line does not expand under pressure- Harder and more constant pressure point- Improved modulation Scope of delivery: - 2x brake disc perforated left/right incl. brake pot - 1x mounting material - 1x installation instructions and running-in instructions - 1x parts certificate - 2x sports brake pad (only bundle 2+3) - 2x steel flex lines VA + HA (only bundle 3) Compatible vehicles:Seat Leon III (5F) Cupra PP 2.0 TSI 195kW / 265PS / 1984cm³Seat Leon III (5F) Cupra PP 2.0 TSI 206kW / 280PS / 1984cm³Seat Leon III (5F) Cupra PP 2.0 TSI 213kW / 290PS / 1984cm³Seat Leon III (5F) Cupra PP 2.0 TSI 221kW / 300PS / 1984cm³Seat Leon III (5F) Cupra R PP 2.0 TSI 228kW / 310PS / 1984cm³Cupra Formentor (KM) VZ 2.0 TSI 180kW / 245PS / 1984cm³Cupra Formentor (KM) VZ 2.0 4Drive TSI 228kW / 310PS / 1984cm³Cupra Formentor (KM) 2.0 TSI 140kW / 190PS / 1984cm³Cupra Formentor (KM) 2.0 TSI 4Drive 140kW / 190PS / 1984cm³Cupra Ateca (KH) 2.0 TSI 4Drive 140kW / 190PS / 1984cm³Cupra Ateca (KH) 2.0 TSI 4Drive 221kW / 300PS / 1984cm³ Notes:When fitting the upgrade kit, we always recommend replacing the brake pads, as the use of used pads on new brake discs is not recommended.When fitted in our factory, the conversion is carried out exclusively with new brake pads!

A powerful brake is one of the most important components in motorsport.With these upgrade kits, the necessary balance of performance, weight and durability has been perfectly combined through the uncompromising selection of materials, so that this product can meet the high demands of extreme automotive applications.To achieve this, MOV'IT has increased the diameter and thickness of the brake discs and used more cross holes. Each pre-cast hole is re-drilled and countersunk to achieve a more favorable flow.The optimized DDE ventilation system of the brake disc has an 80% larger surface area compared to other brake discs, resulting in a significant reduction in temperature and wear. Attention: The conversion means that only rims with at least 19 inches can be fitted! The chassis number of the vehicle on which the brakes are fitted is required to create the parts certificate. Bundle Street 1:- Upgrade kit front axle, 380mm, 2-piece disk, perforated- incl. parts certificate Bundle Street 2 (+ sports brake pads):- Upgrade kit front axle, 380mm, 2-piece disk, perforated- MOVIT sports brake pads- incl. parts certificate Street 3 bundle (+ sports brake pads + steel flex lines):- Upgrade kit front axle, 380mm, 2-piece disk, perforated- MOVIT sports brake pads- Steel flex lines for front and rear axle- incl. parts certificate Details:MOVIT steel brake discs, 2-piece- Highly efficient DDE cooling system- Maximum fading protection- Double, directional ventilation- Perforated for optimum response even on wet roads- Special alloy for high thermal conductivityMOVIT sports brake pads, front axle- For the original brake caliper- Optimally compatible with MOVIT brake discs- Enlarged friction surface- Even heat transfer- Longer service life- With road approval- Low noise development- Lower system temperature for the perfect friction coefficientMOVIT steel flex lines, front and rear axle- Better response behavior of the brake system- Durable quality (does not become porous and therefore does not leak)- Brake line does not expand under pressure- Harder and more constant pressure point- Better modulation Scope of delivery:- 2x brake disk perforated left/right incl. brake pot- 1x mounting material- 1x installation instructions and running-in instructions- 1x parts certificate- 2x sports brake pad (only bundle 2+3)- 2x steel flex lines VA + HA (only bundle 3) Compatible vehicles:Audi A3 (8V) Sportback RS3 quattro 270kW / 367PS / 2480cm³Audi A3 (8V) Sportback RS3 quattro 294kW / 400PS / 2480cm³Audi A3 (8V) Sedan RS3 quattro 294kW / 400PS / 2480cm³Audi TT (FV/8J1/8S) Coupé TTRS quattro 294kW / 400PS / 2480cm³Audi TT (FV/8J1/8S) Roadster TTRS quattro 294kW / 400PS / 2480cm³ Notes:When fitting the upgrade kit, we always recommend replacing the brake pads, as the use of used pads on new brake discs is not recommended.If the upgrade kit is fitted in our workshop, only new brake pads are used!

A powerful brake is one of the most important components in motorsport. With these upgrade kits, the necessary balance of performance, weight and durability has been perfectly combined through the uncompromising selection of materials, so that this product can meet the high demands of extreme automotive applications. To achieve this, MOV'IT has increased the diameter and thickness of the brake discs and used more cross holes. Each pre-cast hole is re-drilled and countersunk to achieve a more favourable flow. The brake disc's optimised DDE ventilation system has an 80% larger surface area compared to other brake discs, resulting in a significant reduction in temperature and wear. Attention: The conversion means that only rims with at least 19 inches can be fitted! The chassis number of the vehicle on which the brakes are fitted is required for the parts certificate. Features: - Upgrade kit front axle, 380mm, 2-piece disc, perforated - incl. parts certificateDetails:MOVIT steel brake discs, 2-piece- Highly efficient cooling system- Double, directional ventilation- Special alloy- High thermal conductivity- Highest fading resistanceMOVIT sports brake pads, front axle- Optimally compatible with MOVIT brake discs- Maximum durability with low wear- With road approval- Low noise development- Low base temperature for the perfect coefficient of frictionMOVIT steel flex lines, front and rear axle- Better response behaviour of the brake system- Durable quality (does not become porous and therefore does not leak)- Brake line does not expand under pressure- Harder and more constant pressure point- Improved modulation Scope of delivery: - 2x brake disc left/right incl. brake pot - 1x mounting material - 1x installation instructions and running-in instructions - 1x parts certificate Compatible vehicles:Audi A4 B8 (8K5) Avant RS4 quattro 331kW / 450PS / 4163cm³Audi A5 (8T3) RS5 quattro 331kW / 450PS / 4163cm³ Notes:When installing the upgrade kit, we always recommend replacing the brake pads, as the use of used pads on new brake discs is not recommended.When installed in our factory, the conversion is carried out exclusively with new brake pads!

A powerful brake is one of the most important components in motorsport. With these upgrade kits, the necessary balance of performance, weight and durability has been perfectly combined through the uncompromising selection of materials, so that this product can meet the high demands of extreme automotive applications. To achieve this, MOV'IT has increased the diameter and thickness of the brake discs and used more cross holes. Each pre-cast hole is re-drilled and countersunk to achieve a more favourable flow. The brake disc's optimised DDE ventilation system has an 80% larger surface area compared to other brake discs, resulting in a significant reduction in temperature and wear. Attention: The conversion means that only rims with at least 19 inches can be fitted! The chassis number of the vehicle on which the brakes are fitted is required for the parts certificate. Bundle Street 1: - Upgrade kit front axle, 382mm, 2-piece disc, perforated - incl. parts certificate Bundle Street 2 (+ sports / comfort brake pads): - Upgrade kit front axle, 382mm, 2-piece disc, perforated - MOVIT sports or comfort brake pads - incl. parts certificate Street 3 bundle (+ sports / comfort brake pads + steel flex lines): - Upgrade kit front axle, 382mm, 2-piece disc, perforated - MOVIT sports or comfort brake pads - Steel flex lines for front and rear axle - incl. parts certificate Details:MOVIT steel brake discs, 2-piece- Highly efficient DDE cooling system- Maximum fading protection- Double, directional ventilation- Perforated for optimum response behaviour even on wet roads- Special alloy for high thermal conductivityMOVIT sports brake pads, front axle- For the original brake caliper- Optimally compatible with MOVIT brake discs- Enlarged friction surface- Even heat transfer- Longer service life- With road approval- Low noise development- Lower system temperature for the perfect coefficient of frictionMOVIT comfort brake pads, front axle- Enlarged friction surface- Even heat transfer- Lower system temperature- Longer service lifeMOVIT steel flex lines, front and rear axle- Better response behaviour of the brake system- Durable quality (does not become porous and therefore does not leak)- Brake line does not expand under pressure- Harder and more constant pressure point- Improved modulation Scope of delivery: - 2x brake disc perforated left/right incl. brake pot - 1x mounting material - 1x installation instructions and running-in instructions - 1x parts certificate - 2x sports / comfort brake pad (only bundle 2+3) - 2x steel flex lines VA + HA (only bundle 3) Compatible vehicles:Audi A3 (8Y) RS3 quattro 294kW / 400PS / 2480cm³Audi A3 (8Y) RS3 quattro 299kW / 407PS / 2480cm³Audi Q3 (F3) RSQ3 quattro 294kW / 400PS / 2480cm³Cupra Formentor (KM7) VZ5 2.5 TSI 287kW / 390PS / 2480cm³ / 4Drive Notes:When installing the upgrade kit, we always recommend replacing the brake pads, as the use of used pads on new brake discs is not recommended.When installed in our factory, the conversion is carried out exclusively with new brake pads!

A powerful brake is one of the most important components in motorsport. With these upgrade kits, the necessary balance of performance, weight and durability has been perfectly combined through the uncompromising selection of materials, so that this product can meet the high demands of extreme automotive applications. To achieve this, MOV'IT has increased the diameter and thickness of the brake discs and used more cross holes. Each pre-cast hole is re-drilled and countersunk to achieve a more favourable flow. The brake disc's optimised DDE ventilation system has an 80% larger surface area compared to other brake discs, resulting in a significant reduction in temperature and wear. Attention: The conversion means that only rims with at least 19 inches can be fitted! The chassis number of the vehicle on which the brakes are fitted is required for the parts certificate. Bundle Street 1: - Upgrade kit front axle, 382mm, 2-piece disc, slotted - incl. parts certificate Bundle Street 2 (+ sports / comfort brake pads): - Upgrade kit front axle, 382mm, 2-piece disc, slotted - MOVIT sports or comfort brake pads - incl. parts certificate Street 3 bundle (+ sports / comfort brake pads + steel flex lines): - Upgrade kit front axle, 382mm, 2-piece disc, slotted - MOVIT sports or comfort brake pads - Steel flex lines for front and rear axle - incl. parts certificate Details:MOVIT steel brake discs, 2-piece- Highly efficient DDE cooling system- Maximum fading protection- Double, directional ventilation- Perforated for optimum response behaviour even on wet roads- Special alloy for high thermal conductivityMOVIT sports brake pads, front axle- For the original brake caliper- Optimally compatible with MOVIT brake discs- Enlarged friction surface- Even heat transfer- Longer service life- With road approval- Low noise development- Lower system temperature for the perfect coefficient of frictionMOVIT comfort brake pads, front axle- Enlarged friction surface- Even heat transfer- Lower system temperature- Longer service lifeMOVIT steel flex lines, front and rear axle- Better response behaviour of the brake system- Durable quality (does not become porous and therefore does not leak)- Brake line does not expand under pressure- Harder and more constant pressure point- Improved modulation Scope of delivery: - 2x brake disc slotted left/right incl. brake pot - 1x mounting material - 1x installation instructions and running-in instructions - 1x parts certificate - 2x sports / comfort brake pad (only bundle 2+3) - 2x steel flex lines VA + HA (only bundle 3) Compatible vehicles:Audi A3 (8Y) RS3 quattro 294kW / 400PS / 2480cm³Audi A3 (8Y) RS3 quattro 299kW / 407PS / 2480cm³Audi Q3 (F3) RSQ3 quattro 294kW / 400PS / 2480cm³Cupra Formentor (KM7) VZ5 2.5 TSI 287kW / 390PS / 2480cm³ / 4Drive Notes:When installing the upgrade kit, we always recommend replacing the brake pads, as the use of used pads on new brake discs is not recommended.When installed in our factory, the conversion is carried out exclusively with new brake pads!

Features with ABEwith parts certificate Manufactured according to DIN ISO 9001 Complies with US standard FMVSS 106 and DOT Almost unlimited durability 5 year guarantee Tensile strength over 250 kp V2A crimping Burst pressure > 1000 bar Minimum bending radius 25 mm Operating temperature -70°C - 260°C Resistant to all weather conditions Connections can be twisted for stress-free installation High-strength aluminium, brass or stainless steel connections Customised designs possible for all vehicles What are the advantages of a Fischer steel flex brake hose? Our steel flex brake lines provide car and motorbike drivers with an increased level of safety when braking, as steel flex lines - in contrast to conventional brake lines - do not expand even when exposed to high temperatures and therefore respond more quickly and directly. Especially in extreme situations, Fischer steel flex brake lines offer a decisive advantage when braking. In addition, our brake lines are practically indestructible. Once Fischer-Stahlflex brake lines have been used, it is no longer necessary to replace them. We are convinced of our product and that is why you get a 5-year guarantee on all Fischer steel flex brake lines. High-quality steel flex lines from Fischer-Hydraulik The steel flex products fulfil the highest quality standards and are checked by our team before dispatch. It goes without saying that Fischer-Hydraulik GmbH is a TÜV-certified company, i.e. we always supply your brake hose as a pre-assembled complete set with a general operating licence (ABE). You can therefore rely on our decades of experience in the manufacture of steel flex kits and customised products for your vehicle. Compatible vehicles:VehicleTypePowerEngine capacityEngineYear of constructionBMW 2 Series Coupe (F87)M2 Competition302kW / 411hp2979ccS55 B30 A06.18 - 06.21BMW 2 Series Coupe (F87)M2 CS331kW / 450hp2979ccS55 B30 A11.19 - 06.21

Featureswith ABEwith parts certificateManufactured in accordance with DIN ISO 9001Complies with US standard FMVSS 106 and DOTAlmost unlimited durability5 year guaranteeTensile strength over 250 kpV2A compressionBurst pressure > 1000 barMinimum bending radius 25 mmOperating temperature -70°C - 260°CResistant to all weather conditionsConnections can be twisted for stress-free installationHigh-strength aluminum, brass or stainless steel connectionsSpecial designs possible for all vehicles What are the advantages of a Fischer steel flex brake line?Our steel flex brake lines provide car and motorcycle drivers with an increased level of safety when braking, as steel flex lines - in contrast to conventional brake lines - do not expand even when exposed to high temperatures and therefore respond faster and more directly.Especially in extreme situations, Fischer steel flex brake lines offer a decisive advantage when braking.In addition, our brake lines are practically indestructible.Once Fischer-Stahlflex brake lines have been used, it is no longer necessary to replace them.We are convinced of our product and that is why you get a 5-year guarantee on all Fischer steel flex brake lines. High-quality steel flex lines from Fischer-HydraulikThe steel flex products meet the highest quality standards and are checked by our team before dispatch.It goes without saying that Fischer-Hydraulik GmbH is a TÜV-certified company, which means that we always supply your brake hose as a pre-assembled complete set with a general operating permit (ABE).You can therefore rely on our decades of experience in the manufacture of steel flex kits and custom-made products for your vehicle. Compatible vehicles:VehiclesTypePowerEngine capacityEngineYear of construction BMW 3er (F80)M3317kW / 431hp2979cm³S55 B30 A03.14 - 10.18 BMW 3er (F80)M3 Competition331kW / 450hp2979cm³S55 B30 A03.16 - 10.18 BMW 3er (F80)M3 CS338kW / 460hp2979cm³S55 B30 A01.18 - 10.18 BMW 4er (F82/F83)M4317kW / 431hp2979cm³S55 B30 A03.14 - 07.20 BMW 4er (F82/F83)M4 Competition331kW / 450hp2979cm³S55 B30 A03.16 - 07.20 BMW 4er Coupe (F82)M4 CS338kW / 460hp2979cm³S55 B30 A07.17 - 06.19 BMW 4er Coupe (F82)M4 GTS368kW / 500hp2979cm³S55 B30 A03.16 - 06.19