Lowering springs 30mm/10mm | fits BMW M3 Sedan incl. Competition (G80) | 28616-1 | H&R
€526.00*
Delivery time: approx. 1-5 working days*
Finanzieren Sie ihren Einkauf über die Targobank.
×
Ratenrechner
Ihre Monatsraten
6 Monate
Kaufpreis:
Monatliche Rate:
Zinsen:
Gesamtbetrag inkl. Zinsen:
Product number:
HR286161
Product information "Lowering springs 30mm/10mm | fits BMW M3 Sedan incl. Competition (G80) | 28616-1 | H&R"
H&R lowering springs for G80 2020-, only with adaptive damping VA30/HA10mm
H&R sports spring kits are the ideal solution if you want to optimize the handling of your vehicle and achieve a sporty look while retaining the standard ride comfort.
Details:
Lowering VA: 30mm
Lowering HA: 10mm
Axle load front: up to 1080 kg
Rear axle load: up to 1180 kg
Chassis: for vehicles with electric damper control
Type of approval: with general operating permit (ABE)
Product benefits:
Sporty look and performance
Lowering of the vehicle's center of gravity
Linear or progressive suspension characteristics
Can be combined with standard or retrofit dampers
Optimized driving dynamics
Surface protection through powder coating
Made in Germany
Compatible vehicles:
BMW M3 (G80) incl. Competition from 2020, only with adaptive M suspension
There aren't any asked questions yet.
Actuator for exhaust flap | fits BMW F8X F9X G8X | 18307851568 | Aulitzky Tuning
€99.00*
Actuator for exhaust flap
OEM part number: 18307851568 (18 30 7 851 568)
Suitable for the following BMW models with exhaust flap:
F80 F82 F83 F85 F86 F87N F90 F91 F92 F93 F95 F96 F97 F98
G01 G02 G05 G06 G14 G15 G16 G20 G21 G22 G23 G26 G30 G42 G82 G83
Air filter | fits BMW M2/M3/M4 incl. Competition/CS/CSL (G80/G81/G82/G87) S58 | Aulitzky Tuning
€149.90*
Here you get a sports air filter with all its advantages:- higher air flow rate- higher filter performance (even smaller particles are filtered)- The particles are trapped in the filter after intake and thus remain trapped until cleaning.- Washable and reusable filter- Increased air flow and therefore better combustion in the engine- No reduction in air flow over a minimum of 50,000 km- Sufficient air even at high engine speeds- more power- Better intake noise- Reduced fuel consumption
These sports air filters have polyurethane as the edge material. Polyurethane is more resistant to petrol, vapours and the like. It has an ideal remoulding. This ensures that the edge of the filter is 100% sealed even when it is reinserted after cleaning.
The edge surface is made from a single mould. With many other makes, pores in the edge material and joining surfaces where the edge is joined together often lead to a crack in the edge, which can result in unclean air being sucked into the engine.
With paper filters, the air flow rate is significantly lower and decreases further after just a short period of use.In addition, paper filters must be disposed of after the specified mileage. TitanTec sports air filters last a lifetime. This is good for the environment and your wallet.Other washable cotton filters only filter much larger particles compared to TitanTec sports air filters.
Cleaning the filters:A TitanTec sports air filter has no oil residue and has 100% of its original performance again after cleaning.Cleaning is quick and easy.We recommend cleaning after 15,000-20,000 kilometres or once a year at the latest.The best time to clean the air filter is around the end of May or beginning of June, i.e. after the pollen count, as this is the time when the air filter is under the most strain.Under no circumstances should aggressive cleaning agents such as petroleum ether, cleaning petrol, brake cleaner etc. be used, as this can damage the material.
Details:
Type: 2x panel filter
Length: 187 mm
Width: 235 mm
Compatible vehicles:
BMW 2 Coupe (G42, G87) M2, 460 hp, 338 kW, from 11/22
BMW 3 (G20, G80, G28) M3, 480 hp, 353 kW, from 11/20
BMW 3 (G20, G80, G28) M3 Competition, 510 hp, 375 kW, from 11/20
BMW 3 (G20, G80, G28) M3 Competition xDrive, 510 hp, 375 kW, from 05/21
BMW 3 (G20, G80, G28) M3 CS xDrive, 551 hp, 405 kW, from 03/23
BMW 3 Touring (G21, G81) M3 Competition xDrive, 510 hp, 375 kW, from 07/22
BMW 4 Coupe (G22, G82) M4, 480 hp, 353 kW, from 11/20
BMW 4 Coupe (G22, G82) M4 Competition, 510 hp, 375 kW, from 11/20
BMW 4 Coupe (G22, G82) M4 Competition M xDrive, 510 hp, 375 kW, from 05/21
BMW 4 Coupe (G22, G82) M4 CSL, 551 hp, 405 kW, 05/22 to 02/23
BMW 4 Convertible (G23, G83) M4 Competition M xDrive, 510 hp, 375 kW, from 07/21
Air inlets Double-Ducts Carbon | fits BMW M3/M4 (G80/G81/G82/G83) | Aulitzky Tuning
€1,349.00*
The carbon replacement air intakes Twin Fin for the G8x were developed to match the channel lines of the SP1 G8X front splitter. With both the SP1 and Twin Fin ducts installed, you get the aggressive angles your front end needs.Our covers are a direct replacement, which means you can finally remove the honeycomb grille that is currently in front of the air ducts.These covers are made of pure pre-preg carbon, so the bumper adds minimal weight while providing the aggressive look you've been wanting.
Details:- 100% pure pre-preg carbon fiber construction- OEM style fabric- High gloss finish- Fit guarantee- Mounts to the OEM front bumper using the original grille clip positions- with parts certificate according to §19.3
Compatible vehicles:- BMW G80 M3/Competition/CS Sedan (2021+)- BMW G81 M3 Competition Touring (2021+)- BMW G82 M4/Competition/CSL Coupe (2021+)- BMW G83 M4 Competition Convertible (2021+)Note: This is NOT an original BMW product!
Air inlets Performance Carbon | fits BMW M3/M4 (G80/G81/G82/G83) | Aulitzky Tuning
€839.00*
The Carbon Performance Twin Fin air intakes for the G8x were developed to give the vehicle a distinctive look. These covers are made of pure pre-preg carbon, so the bumper adds minimal weight while providing the aggressive look you've been wanting.
Details:- 100% pure pre-preg carbon fiber construction- OEM style fabric- High gloss finish- Fit guarantee- with parts certificate according to §19.3
Compatible vehicles:- BMW G80 M3/Competition/CS Sedan (2021+)- BMW G81 M3 Competition Touring (2021+)- BMW G82 M4/Competition/CSL Coupe (2021+)- BMW G83 M4 Competition Convertible (2021+)Note: This is NOT an original BMW product!
Air intake set Carbon | fits BMW M3/M4 incl. Competition/CS/CSL (G80/G81/G82/G83) | Aulitzky Tuning
€989.00*
The Air Intake Set for the G8X models made of carbon fibre gives your vehicle an upscale look.
When you buy Pre-Preg carbon fibre, you are investing in a higher quality and more durable material that will outlast other forms of carbon fibre and potentially save you money in the long run.
Scope of delivery:- 1x Air Intake Set
Details:- 100% carbon fibre construction- High gloss finish- Fit guarantee
Compatible vehicles with S58 engine:- BMW G80 M3 (all models)- BMW G81 M3 (all models)- BMW G82 M4 (all models)- BMW G83 M4 (all models)
Note: This is NOT an original BMW product!
Armrest Alcantara / Leather | fits BMW M2/M3/M4 (G80/G81/G82/G83/G87) | Aulitzky Tuning
Add a touch of luxury to the interior of your G8X with this custom-made center armrest in high-quality leather or Alcantara.
The red contrast stitching creates a sporty look inspired by motorsport. Fully compatible with the Karbonius center console and easy to install without any modifications.
Features:
- Available in high-quality leather or Alcantara
- Red motorsport-style stitching
- Quick installation – no modifications required
- Exclusive design for a personalized interior
Scope of delivery:
- 1x center armrest
Compatible vehicles:
- BMW G87 M2
- BMW G80 M3
- BMW G81 M3
- BMW G82 M4
- BMW G83 M4
Note: This is NOT an original BMW product!
€350.00*
Tip
Aulitzky Exhaust | ECE downpipe with sports catalyst | fits BMW M2/M3/M4 incl. Competition/CS/CSL (G80/G81/G82/G83/G87) S58
From
€3,699.00*
Facts:
- 2x 3” (76mm), replaces the main catalyst
- with 200 cell stainless steel sports catalyst
- Euro 6 compatible
- for current OPF models
- with Thermo-Integral insulation (for an extra charge)
- with ECE approval*
Compatible vehicles:VehicleVehicle typePowerCapacityEngineYear of construction
BMW 2er (G87)M2338kW / 460hp2993cm³S58 B30 A11.22 -
BMW 3 Series (G80)M3353kW / 480hp2993cm³S58 B30 B11.20 -
BMW 3 Series (G80/G81)M3 Competition / xDrive375kW / 510hp390kW / 530hp2993cm³S58 B30 A05.21 -07.24 -
BMW 3 Series (G80)M3 CS xDrive405kW / 551hp2993cm³S58 B30 A03.23 -
BMW 4 Series (G82)M4353kW / 480hp2993cm³S58 B30 B11.20 -
BMW 4 Series (G82/G83)M4 Competition / M xDrive375kW / 510hp2993cm³S58 B30 A11.20 -
BMW 4 Series (G82)M4 CSL xDrive405kW / 551hp412kW / 560hp2993cm³S58 B30 A05.22 - 02.2311.22 - 02.23
Note: Depending on the software version, the engine control light may light up. We recommend the purchase of an OFF set module or software customisation.
*This downpipe has ECE approval so that it can be used within the scope of the German Road Traffic Licensing Regulations (StVZO) without registration in the vehicle documents.
Tip
Aulitzky Exhaust | ECE exhaust system 3" (76mm) from OPF with flap control | fits BMW M3/M4 incl. Competition/CS/CSL (G80/G81/G82/G83) S58
€4,199.00*
Surface:
blasted (glass beads)
Facts:
- Tailpipes: 4x100mm black
- 3.0 inch stainless steel
- MSD removal
- Mounting for the original electric flap actuator
- Made in Germany (Lake Constance)
- with ECE approval*
Scope of delivery:
- 1x Aulitzky Exhaust exhaust system from OPF
- 4x tailpipes 100mm black
- ECE handout
Compatible vehicles:VehicleVehicle typePower outputDisplacementEngineYear of construction
BMW 3 Series (G80)M3353kW / 480PS2993cm³S58 B30 B11.20 -
BMW 3 Series (G80/G81)M3 Competition / xDrive375kW / 510PS390kW / 530PS2993cm³S58 B30 A05.21 -07.24 -
BMW 3 Series (G80)M3 CS xDrive405kW / 551PS2993cm³S58 B30 A03.23 -
BMW 4 Series (G82)M4353kW / 480PS2993cm³S58 B30 B11.20 -
BMW 4 Series (G82/G83)M4 Competition / M xDrive375kW / 510PS2993cm³S58 B30 A11.20 -
BMW 4 Series (G82)M4 CSL xDrive405kW / 551hp2993cm³S58 B30 A05.22
*The ECE and the combination certificate for the pre-facelift and facelift models are available (includes intake, intercooler, boost pipe kit, downpipe, exhaust system, 670hp Aulitzky App performance increase and 107dB increase in stationary noise).
In conjunction with the standard flap control system (with type approval), this flap exhaust system has ECE approval, meaning that it can be used legally within the scope of the German Road Traffic Licensing Regulations (StVZO) without registration in the vehicle documents.
Variants from €3,999.00*
Aulitzky Exhaust | Race flap control module | fits BMW M3/M4 incl. Competition (G80/G81/G82/G83) S58 | Motorsport articles
€449.00*
Function:- variable flap control of the original or retrofitted flap exhaust system- controllable via steering wheel buttons
Compatible vehicles:
VehicleTypePowerEngine capacityEngine typeYear of constructionBMW 3er (G80)M3353kW / 480hp2993cm³S58 B30 B11.20 -BMW 3er (G80/G81)M3 Competition / xDrive375kW / 510hp2993cm³S58 B30 A05.21 -BMW 4er (G82)M4353kW / 480hp2993cm³S58 B30 B11.20 -BMW 4er (G82/G83)M4 Competition / M xDrive375kW / 510hp2993cm³S58 B30 A05.21 -
Note:
This product is NOT StVZO approved and NOT intended for sale within the EU!
This item is for show & motorsport purposes only and must not be used/installed on public roads.
If the component is installed on/in the vehicle, the operating license expires!
The pictures shown are examples.
Tip
Aulitzky Tuning | Cooler and intake package | fits BMW M2/M3/M4 incl. Competition/CS/CSL (G80/G81/G82/G83/G87) S58
€3,999.00*
The Aulitzky Tuning Cooler and intake package for the S58 engines of the G8x series was developed to meet the high demands of the engine.
With combination certificate!*
Compatible vehicles:VehicleVehicle typePowerCapacityEngineYear of construction
BMW 2er (G87)M2338kW / 460hp2993cm³S58 B30 A11.22 -
BMW 3 Series (G80)M3353kW / 480hp2993cm³S58 B30 B11.20 -
BMW 3 Series (G80/G81)M3 Competition / xDrive375kW / 510hp390kW / 530hp2993cm³S58 B30 A05.21 -07.24 -
BMW 3 Series (G80)M3 CS xDrive405kW / 551hp2993cm³S58 B30 A03.23 -
BMW 4 Series (G82)M4353kW / 480hp2993cm³S58 B30 B11.20 -
BMW 4 Series (G82/G83)M4 Competition / M xDrive375kW / 510hp2993cm³S58 B30 A11.20 -
BMW 4 Series (G82)M4 CSL xDrive405kW / 551hp412kW / 560hp2993cm³S58 B30 A05.22 - 02.2311.22 - 02.23
*The combination certificate for the pre-facelift and facelift models is available (includes intake manifold, intake, intercooler, boost pipe kit, downpipe, exhaust system, 670hp Aulitzky App performance increase and 107dB increase in stationary noise).
Tip
Aulitzky Tuning | Intake manifold | fits BMW M2/M3/M4 incl. Competition/CS/CSL (G80/G81/G82/G83/G87) S58
€3,999.00*
The Aulitzky Tuning intake manifold for the S58 engines of the G8x series was developed to meet the high demands of the engine.
Advantages:
- Improved cooling performance with up to 20° cooler intake air temperatures
- Maximum mechanical and thermal relief for the turbocharger
- Increase in power and torque
- Absolute pressure resistance and reliability
- Easy installation thanks to plug-and-play
- 1/8 NPT connections for measuring and monitoring additional parameters
- Optimally suited for all performance levels
With combination certificate!*
Compatible vehicles:VehicleVehicle typePowerCapacityEngineYear of construction
BMW 2er (G87)M2338kW / 460hp2993cm³S58 B30 A11.22 -
BMW 3 Series (G80)M3353kW / 480hp2993cm³S58 B30 B11.20 -
BMW 3 Series (G80/G81)M3 Competition / xDrive375kW / 510hp390kW / 530hp2993cm³S58 B30 A05.21 -07.24 -
BMW 3 Series (G80)M3 CS xDrive405kW / 551hp2993cm³S58 B30 A03.23 -
BMW 4 Series (G82)M4353kW / 480hp2993cm³S58 B30 B11.20 -
BMW 4 Series (G82/G83)M4 Competition / M xDrive375kW / 510hp2993cm³S58 B30 A11.20 -
BMW 4 Series (G82)M4 CSL xDrive405kW / 551hp412kW / 560hp2993cm³S58 B30 A05.22 - 02.2311.22 - 02.23
*The combination certificate for the pre-facelift and facelift models is available (includes intake manifold, intake, intercooler, boost pipe kit, downpipe, exhaust system, 670hp Aulitzky App performance increase and 107dB increase in stationary noise).
Tip
Aulitzky Tuning | Portinjection Rail | fits BMW M2/M3/M4 incl. Competition/CS/CSL (G80/G81/G82/G83/G87) S58
€199.00*
The Aulitzky Tuning Portinjection Rail for the S58 engines of the G8x series was developed to meet the high demands of the engine.Compatible vehicles:VehicleVehicle typePowerCapacityEngineYear of construction
BMW 2er (G87)M2338kW / 460hp2993cm³S58 B30 A11.22 -
BMW 3 Series (G80)M3353kW / 480hp2993cm³S58 B30 B11.20 -
BMW 3 Series (G80/G81)M3 Competition / xDrive375kW / 510hp390kW / 530hp2993cm³S58 B30 A05.21 -07.24 -
BMW 3 Series (G80)M3 CS xDrive405kW / 551hp2993cm³S58 B30 A03.23 -
BMW 4 Series (G82)M4353kW / 480hp2993cm³S58 B30 B11.20 -
BMW 4 Series (G82/G83)M4 Competition / M xDrive375kW / 510hp2993cm³S58 B30 A11.20 -
BMW 4 Series (G82)M4 CSL xDrive405kW / 551hp412kW / 560hp2993cm³S58 B30 A05.22 - 02.2311.22 - 02.23
Aulitzky Tuning | Radhausgitter mit Bremsen Belüftungsgitter Set | passend für BMW M2/M3/M4 inkl. Competition/CS/CSL (G80/G81/G82/G83/G87) S58
€229.00*
Wer einen S58-befeuerten G8X bewegt, kennt das Detail, das BMW ab Werk offen gelassen hat: An einer Stelle der vorderen Radhausschale schleift das Material genau dort, wo ein Lüftungsgitter sitzt — auf Dauer ein Scheuern, das niemand am M2, M3 oder M4 sehen will. Das Aulitzky Lüftungsgitter-Set löst dieses Problem an der Wurzel und macht aus einer Schwachstelle gleich zwei Vorteile.
Das erste Gitter ersetzt den kritischen Bereich der Radhausschale und sorgt dafür, dass nichts mehr schleift — sauber abgedeckt, formstabil und dauerhaft. Das zweite Gitter geht einen Schritt weiter: Hinter einer ab Werk verschlossenen Abdeckung sitzt am G8X bereits ein vorhandener Lüftungskanal zur Bremse. Dieser Kanal wird geöffnet und mit dem Aulitzky-Gitter zugleich gesichert. Das Ergebnis ist eine spürbar bessere Anströmung der vorderen Bremse, während das engmaschige Wabengitter den Kanal vor Steinschlag und Schmutz schützt.
Beide Gitter tragen den eingelaserten AULITZKY-Schriftzug im markanten Wabendesign. Das ist kein Zubehör von der Stange, sondern eine durchdachte Lösung vom Spezialisten für BMW M — Performance-Tuning mit Namen, das funktionalen Mehrwert und sichtbare Veredelung in einem Set vereint.
Konstruiert und gefertigt für die komplette S58-G8X-Range: passend für BMW M2 (G87), BMW M3 (G80/G81) und BMW M4 (G82/G83).
Tip
Aulitzky Tuning | Transmission oil cooler | fits BMW M2/M3/M4 incl. Competition/CS/CSL (G80/G81/G82/G83/G87) S58
€789.00*
The Aulitzky Tuning transmission oil cooler for the S58 engines of the G8x series was developed to meet the high demands of the engine.
Advantages:
- Specially developed for the S58 3.0L R6 biturbo engine
- Ensures that the oil temperature remains within the optimum range even under extreme conditions
- Particularly suitable for performance-enhanced vehicles
With combination certificate!*
Compatible vehicles:VehicleVehicle typePowerCapacityEngineYear of construction
BMW 2er (G87)M2338kW / 460hp2993cm³S58 B30 A11.22 -
BMW 3 Series (G80)M3353kW / 480hp2993cm³S58 B30 B11.20 -
BMW 3 Series (G80/G81)M3 Competition / xDrive375kW / 510hp390kW / 530hp2993cm³S58 B30 A05.21 -07.24 -
BMW 3 Series (G80)M3 CS xDrive405kW / 551hp2993cm³S58 B30 A03.23 -
BMW 4 Series (G82)M4353kW / 480hp2993cm³S58 B30 B11.20 -
BMW 4 Series (G82/G83)M4 Competition / M xDrive375kW / 510hp2993cm³S58 B30 A11.20 -
BMW 4 Series (G82)M4 CSL xDrive405kW / 551hp412kW / 560hp2993cm³S58 B30 A05.22 - 02.2311.22 - 02.23
*The combination certificate for the pre-facelift and facelift models is available (includes intake manifold, intake, intercooler, boost pipe kit, downpipe, exhaust system, 670hp Aulitzky App performance increase and 107dB increase in stationary noise).
Aulitzky Tuning | Unterfahrschutz | passend für BMW M2/M3/M4 inkl. Competition/CS/CSL (G80/G81/G82/G83/G87) S58
€599.00*
Der S58 hängt seinen Ölkühler tief und flach unter der Front — strömungstechnisch clever, aber im Alltag eine offene Flanke. Ab Werk schützt nur eine Kunststoff-Unterbodenverkleidung mit großer Öffnung, und genau dort treffen Steinschlag, Splitt, Eisbrocken oder die Kante eines Parkriegels ungebremst auf den Kühler. Ein einziger harter Treffer kann den Ölkühler aufreißen — mit Ölverlust und im schlimmsten Fall einem Motorschaden als Folge. Bei einem Triebwerk vom Kaliber des S58 ist das ein Risiko, das niemand eingehen muss.
Der Aulitzky Ölkühler-Unterfahrschutz ersetzt die anfällige Serienverkleidung durch eine robuste Metallkonstruktion, die den Ölkühler und die darunterliegenden Bauteile zuverlässig abschirmt. Das Herzstück ist das integrierte Wabengitter: Es lässt die volle Kühlluft an den Ölkühler — die Öltemperaturen bleiben dort, wo sie hingehören — und fängt zugleich alles ab, was dem Kühler gefährlich werden könnte. Schutz und Kühlleistung schließen sich hier nicht aus, sondern gehen Hand in Hand.
Gefertigt aus pulverbeschichtetem Metall, formstabil und korrosionsfest, mit eingelasertem AULITZKY-Schriftzug im markanten Wabendesign. Die Montage erfolgt anstelle der Original-Verkleidung an den vorhandenen Aufnahmepunkten — kein Provisorium, sondern eine sauber integrierte Lösung. Das ist Performance-Tuning mit Namen: durchdachter Bauteilschutz vom Spezialisten für BMW M, der unter dem Auto sitzt und seinen Job macht — auch wenn man ihn nicht sieht. Passend für die komplette S58-G8X-Range: BMW M2 (G87), BMW M3 (G80/G81) und BMW M4 (G82/G83), inkl. Competition.
Tip
Aulitzky Tuning | Water cooler Set side-mounted | fits BMW M2/M3/M4 incl. Competition/CS/CSL (G80/G81/G82/G83/G87) S58
€949.00*
The side-mounted Aulitzky Tuning water cooler for the S58 engines of the G8x series was developed to meet the high demands of the engine.
Advantages:
- Specially developed for the S58 3.0L R6 biturbo engine
- Constant maximum performance
- Thermal stabilization
With combination certificate!*
Compatible vehicles:VehicleVehicle typePowerCapacityEngineYear of construction
BMW 2er (G87)M2338kW / 460hp2993cm³S58 B30 A11.22 -
BMW 3 Series (G80)M3353kW / 480hp2993cm³S58 B30 B11.20 -
BMW 3 Series (G80/G81)M3 Competition / xDrive375kW / 510hp390kW / 530hp2993cm³S58 B30 A05.21 -07.24 -
BMW 3 Series (G80)M3 CS xDrive405kW / 551hp2993cm³S58 B30 A03.23 -
BMW 4 Series (G82)M4353kW / 480hp2993cm³S58 B30 B11.20 -
BMW 4 Series (G82/G83)M4 Competition / M xDrive375kW / 510hp2993cm³S58 B30 A11.20 -
BMW 4 Series (G82)M4 CSL xDrive405kW / 551hp412kW / 560hp2993cm³S58 B30 A05.22 - 02.2311.22 - 02.23
*The combination certificate for the pre-facelift and facelift models is available (includes intake manifold, intake, intercooler, boost pipe kit, downpipe, exhaust system, 670hp Aulitzky App performance increase and 107dB increase in stationary noise).
Tip
Aulitzky Tuning | Water cooler Set side-mounted | fits BMW M2/M3/M4 incl. Competition/CS/CSL (G80/G81/G82/G83/G87) S58
€189.00*
The side-mounted Aulitzky Tuning water cooler for the S58 engines of the G8x series was developed to meet the high demands of the engine.
Advantages:
- Specially developed for the S58 3.0L R6 biturbo engine
- Constant maximum performance
- Thermal stabilization
With combination certificate!*
Compatible vehicles:VehicleVehicle typePowerCapacityEngineYear of construction
BMW 2er (G87)M2338kW / 460hp2993cm³S58 B30 A11.22 -
BMW 3 Series (G80)M3353kW / 480hp2993cm³S58 B30 B11.20 -
BMW 3 Series (G80/G81)M3 Competition / xDrive375kW / 510hp390kW / 530hp2993cm³S58 B30 A05.21 -07.24 -
BMW 3 Series (G80)M3 CS xDrive405kW / 551hp2993cm³S58 B30 A03.23 -
BMW 4 Series (G82)M4353kW / 480hp2993cm³S58 B30 B11.20 -
BMW 4 Series (G82/G83)M4 Competition / M xDrive375kW / 510hp2993cm³S58 B30 A11.20 -
BMW 4 Series (G82)M4 CSL xDrive405kW / 551hp412kW / 560hp2993cm³S58 B30 A05.22 - 02.2311.22 - 02.23
*The combination certificate for the pre-facelift and facelift models is available (includes intake manifold, intake, intercooler, boost pipe kit, downpipe, exhaust system, 670hp Aulitzky App performance increase and 107dB increase in stationary noise).
Tip
Aulitzky Tuning | Water cooler | fits BMW M2/M3/M4 incl. Competition/CS/CSL (G80/G81/G82/G83/G87) S58
€1,159.00*
The Aulitzky Tuning water cooler for the S58 engines of the G8x series was developed to meet the high demands of the engine.
Advantages:
- Specially developed for the S58 3.0L R6 biturbo engine
- 60% increase in cooler volume
- Constant maximum performance
- Thermal stabilization
With combination certificate!*
Compatible vehicles:VehicleVehicle typePowerCapacityEngineYear of construction
BMW 2er (G87)M2338kW / 460hp2993cm³S58 B30 A11.22 -
BMW 3 Series (G80)M3353kW / 480hp2993cm³S58 B30 B11.20 -
BMW 3 Series (G80/G81)M3 Competition / xDrive375kW / 510hp390kW / 530hp2993cm³S58 B30 A05.21 -07.24 -
BMW 3 Series (G80)M3 CS xDrive405kW / 551hp2993cm³S58 B30 A03.23 -
BMW 4 Series (G82)M4353kW / 480hp2993cm³S58 B30 B11.20 -
BMW 4 Series (G82/G83)M4 Competition / M xDrive375kW / 510hp2993cm³S58 B30 A11.20 -
BMW 4 Series (G82)M4 CSL xDrive405kW / 551hp412kW / 560hp2993cm³S58 B30 A05.22 - 02.2311.22 - 02.23
*The combination certificate for the pre-facelift and facelift models is available (includes intake manifold, intake, intercooler, boost pipe kit, downpipe, exhaust system, 670hp Aulitzky App performance increase and 107dB increase in stationary noise).
Boost Pipe Kit | fits BMW M2 (G87) 460hp S58 | Wagner Tuning
€590.00*
Suitable for:
BMW M2 G87 S58 338kW/460hp 2993cm³
BMW M2 G87 S58 353kW/480hp 2993cm³
BMW M3 G80 S58 353kW/480hp 2993cm³
BMW M3 Competition/xDrive G80/G81 S58 375kW/510hp 2993cm³
BMW M3 Competition xDrive G80/G81 S58 390kW/530hp 2993cm³
BMW M3 CS xDrive G80 S58 405kW/551hp 2993cm³
BMW M4 G82 S58 353kW/480hp 2993cm³
BMW M4 Competition/M xDrive G82/G83 S58 375kW/510hp 2993cm³
BMW M4 CSL xDrive G82 S58 405kW/551hp 2993cm³
BMW M4 CSL xDrive G82 S58 412kW/560PS 2993cm³
Optimise the performance and responsiveness of your G8X with our high-quality Boost Pipe Kit for the S58 engine. Developed using advanced CFD simulations for maximum flow optimisation, this kit offers a premium solution for demanding drivers looking for a performance boost.
Your benefits:Flow optimised: Each Boost Pipe has been carefully designed using CFD simulations to ensure optimal airflow and improved performance.
Highest pressure resistance: The Boost Pipe Kit has undergone rigorous testing and is pressure resistant up to 6 bar to ensure reliable performance even under extreme conditions.
High quality materials: Made from high quality aluminium for maximum durability and performance.
Precise fit: Each Boost Pipe is customised for a perfect fit and easy installation without the need for additional adjustments.
Improved performance: Optimising the airflow not only increases performance but also improves engine response for an exciting riding experience.
Scope of delivery:1x aluminium boost pipe1x parts certificate
Note:Please note that the product image is for illustrative purposes only and the actual product may differ.
With parts certificate (for easy registration according to §19 paragraph 3 of the StVZO).
Canards Performance Carbon | fits BMW M3/M4 (G80/G81/G82/G83) S58 | Aulitzky Tuning
€499.00*
The high-quality carbon fibre front canards are a perfect addition to significantly enhance the style of your vehicle.
Unlike regular carbon fibre, pre-preg carbon is reinforced to increase strength and durability. It can also be a staggering 70% lighter than other carbon fibre options.Prepreg carbon is far more uniform than other types of carbon, meaning the likelihood of imperfections is drastically reduced. The manufacturing process eliminates unwanted air bubbles and results in a perfectly smooth and high-gloss finish.
Details:- 100% pure prepreg carbon fibre construction- OEM-style weave- High gloss finish- Fit guarantee- With parts certificate according to §19.3
Scope of delivery:- 1x set carbon front canards
Compatible vehicles:
BMW G80 M3 Limousine (2021+)
BMW G80 M3 Competition Limousine (2021+)
BMW G81 M3 Touring (2023+)
BMW G81 M3 Competition Touring (2023+)
BMW G82 M4 Coupe (2021+)
BMW G82 M4 Competition Coupé (2021+)
BMW G83 M4 Cabrio (2021+)
BMW G83 M4 Competition Cabrio (2021+)
Note: This is NOT an original BMW product!
Canards Performance Carbon | fits BMW M3/M4 (G80/G81/G82/G83) S58 | Aulitzky Tuning
€349.00*
The high-quality carbon fibre front canards are a perfect addition to significantly enhance the style of your vehicle.
Unlike regular carbon fibre, pre-preg carbon is reinforced to increase strength and durability. It can also be a staggering 70% lighter than other carbon fibre options.Prepreg carbon is far more uniform than other types of carbon, meaning the likelihood of imperfections is drastically reduced. The manufacturing process eliminates unwanted air bubbles and results in a perfectly smooth and high-gloss finish.
Details:- 100% pure prepreg carbon fibre construction- OEM-style weave- High gloss finish- Fit guarantee- With parts certificate according to §19.3
Scope of delivery:- 1x Performance carbon canards
Compatible vehicles:
BMW G80 M3 Limousine (2021+)
BMW G80 M3 Competition Limousine (2021+)
BMW G81 M3 Touring (2023+)
BMW G81 M3 Competition Touring (2023+)
BMW G82 M4 Coupe (2021+)
BMW G82 M4 Competition Coupé (2021+)
BMW G83 M4 Cabrio (2021+)
BMW G83 M4 Competition Cabrio (2021+)
Note: This is NOT an original BMW product!
Carbon side diffusers | fits BMW M3 incl. Competition (G80/G81) | Aulitzky Tuning
€499.00*
Made from state-of-the-art pre-preg carbon fibre, these side diffusers for the rear emphasise the character of your vehicle and make it stand out both on the road and online.
Why do we use pre-preg carbon fibre?Unlike normal carbon fibre, pre-preg carbon is reinforced to increase strength and durability.It can also be a staggering 70% lighter than other carbon fibre options, ideal for weight saving.In terms of quality, pre-preg carbon is far more consistent, meaning that the likelihood of imperfections is drastically reduced.of imperfections is drastically reduced.The manufacturing process eliminates unwanted air bubbles and results in a perfect, smooth, sleekand high-gloss finish that is the ultimate piece to complement your vehicle.
When you buy Pre-Preg, you are investing in a higher quality, more durable part that will outlast other forms ofoutlast other forms of carbon fibre and potentially save you money in the long run.
Details:- 100% pure prepreg carbon fibre construction- OEM style weave- High-gloss finish- with parts certificate according to §19.3
Scope of delivery:1x set of side diffusers
Compatible vehicles:- BMW G80 M3 Sedan (2021+)- BMW G80 M3 Competition Sedan (2021+)- BMW G81 M3 Competition Touring (2021+)Note: This is NOT an original BMW product!
Centre console side cover carbon | fits BMW M2/M3/M4 incl. Competition (G80/G81/G82/G83/G87) | Aulitzky Tuning
€199.00*
The side centre consoles give your vehicle an upscale look and feel.
When you buy Pre-Preg carbon fibre, you are investing in a higher quality and more durable material that will outlast other forms of carbon fibre and potentially save you money in the long run.
Details:- 100% carbon fibre construction- High gloss finish- Fit guarantee- registration free
Scope of delivery:1x set of centre console side covers (1x right / 1x left)
Compatible vehicles:- BMW G87 M2 - BMW G80 M3 incl. Competition Saloon (2021+)- BMW G81 M3 incl. Competition Touring (2023+)- BMW G82 M4 incl. Competition Coupé (2021+)- BMW G83 M4 incl. Competition Convertible (2021+)
Note: This is NOT an original BMW product!
Charge Pipe Aluminium black | fits BMW M340i/M440i/M40i (G20/G28/G21/G22/G26/G29) B58 | Aulitzky Tuning
€780.00*
Facts:
- Charge pipe made of T-6061 aluminium in black
- incl. mounting rubbers, clamps
- without licence
Compatible vehicles:BMW 3 (G20, G28) (2018-) M 340 i xDrive (B58 B30 B) 2998cm³ 374hp (275kW) 2019 -BMW 3 (G20, G28) (2018-) M 340 i xDrive (B58 B30 B) 2998cm³ 387PS (285kW) 2019 -BMW 3 (G20, G28) (2018-) M 340 i Mild-Hybrid xDrive (B58 B30 B, JA1) 2998cm³ 374PS (275kW) 2020 -BMW 3 Touring Van (G21) (2019-) M 340 i xDrive (B58 B30 B) 2998cm³ 374PS (275kW) 2019 -BMW 4 Coupe (G22) (2020-) M 440 i Mild-Hybrid (B58 B30 B, JA1) 2998cm³ 374PS (275kW) 2021 -BMW 4 Gran Coupe (G26) (2021-) M440 i Mild-Hybrid (B58 B30 B) 2998cm³ 374PS (275kW) 2022 -BMW Z4 Roadster (G29) (2018-) M40 i (B58 B30 C) 2998cm³ 340PS (250kW) 2018 -
Attention: Not approved in the area of the StVZO.
Zuletzt gesehene Produkte
Zuletzt gesehene Produkte
Wheel bolt 10x M14 x 1.25 x 40mm KE60° silver | ST Suspensions
€19.00*
ST wheel nuts & wheel bolts
We recommend ST wheel bolts in silver for fitting the D1, D2, DZ and DZX systems. The wheel bolts must be selected longer by the thickness of the spacer disc. The type of bolt head and thread must also be taken into account.
Important note! The minimum screw-in depth of the wheel bolts must be observed in all cases:
- M12x1.25 min. 8.0 turns- M12x1.5 at least 6.5 turns- M12x1.75 at least 6.5 turns- M14x1.25 min. 9.0 turns- M14x1.5 min. 7.5 turns- M15x1.25 min. 10.0 turns- 1/2" min. 8.0 turns
Caution:If the wheel bolt is too long, the axle parts may be damaged!
Technical information:Item number:56110451Short description: Wheel bolt M14x1.25x40mm KE60° silver (10 pcs.)Colour: silverApproval: Registration-freeScope of delivery: Set (10 pcs.) in boxDesign: Cone 60°Product: Wheel boltThread: M14x1.25Shank length: 40mmKey width: 17mmcollar: tapered collarProduct category: Wheel bolts / Rim locksBrand: ST
Front bumper insert OEM Carbon | fits BMW M2 (G87) S58 | Aulitzky Tuning
€839.00*
Our high quality OEM front bumper insert made from pre-preg carbon fibre is a great addition to significantly increase the style and aggressiveness of your vehicle.
Unlike regular carbon fibre, pre-preg carbon is reinforced to increase strength and durability. It can also be a staggering 70% lighter than other carbon fibre options.Prepreg carbon is far more uniform than other types of carbon, meaning the likelihood of imperfections is drastically reduced. The manufacturing process eliminates unwanted air bubbles and results in a perfectly smooth and high-gloss finish.
Details:- 100% pure prepreg carbon fibre construction- OEM-style weave- High gloss finish- Fit guarantee- Registration according to §21 possible
Scope of delivery:- 1x front bumper insert made from glossy prepreg carbon fibre
Compatible vehicles:BMW G87 2 Series M2 (2023+)
Note: This is NOT an original BMW product!
Engine cover Carbon | fits BMW M5 (G90/G99) S68 | Aulitzky Tuning
€1,299.00*
Our high-quality engine cover made from pre-preg carbon fibre is a great addition to enhance the style of your vehicle.The carbon fibre engine cover replaces the standard plastic part.
When you buy Pre-Preg carbon fibre, you are investing in a higher quality and more durable material that will outlast other forms of carbon fibre and potentially save you money in the long run.
Installation: Plug&Play
Details:- 100% carbon fibre construction- High gloss finish- Performance style design- Supplied with 3M double-sided adhesive tape already attached- Use rubber adapter from the original engine cover + emblem- registration free
Compatible vehicles with S58 engine:- BMW G90 M5 - BMW G99 M5 Touring
Note: This is NOT an original BMW product!
Canards Carbon | fits BMW M2 (G87) S58 | Aulitzky Tuning
€529.00*
The high-quality Canards made from Pre-Preg carbon fibre are an excellent addition to significantly enhance the style of your vehicle.
Unlike regular carbon fibre, Pre-Preg carbon is reinforced to increase strength and durability. It can also be a staggering 70% lighter than other carbon fibre options.Prepreg carbon is far more uniform than other types of carbon, meaning the likelihood of imperfections is drastically reduced. The manufacturing process eliminates unwanted air bubbles and results in a perfectly smooth and high-gloss finish.
Details:- 100% pure prepreg carbon fibre construction- OEM-style weave- High gloss finish- Fit guarantee- Registration according to §21 possible
Scope of delivery:- 1x pair of Canards
Compatible vehicles:BMW G87 2 Series M2
Note: This is NOT an original BMW product!
Side skirts Carbon | fits BMW 3 Series M-Package incl. M340i/M340d (G20) | 3Design
€2,275.00*
Elegant, sporty boot spoiler made of carbon fibre for the 3 Series G20 with M package. No compromises were made in the manufacture and design of the latest addition to the 3D design portfolio: Perfect quality meets a design that blends seamlessly into the design concept of the new G20. Sporty and elegant - a real eye-catcher.
Compatible vehicles:BMW 3 (G20, G80, G28) 316 d since 2020BMW 3 (G20, G80, G28) 316 d Mild-Hybrid Since 2020BMW 3 (G20, G80, G28) 318 d 2019-2020BMW 3 (G20, G80, G28) 318 d Mild-Hybrid Since 2020BMW 3 (G20, G80, G28) 318 i Since 2020BMW 3 (G20, G80, G28) 320 d Since 2018BMW 3 (G20, G80, G28) 320 d Mild-Hybrid Since 2020BMW 3 (G20, G80, G28) 320 d Mild-Hybrid xDrive Since 2020BMW 3 (G20, G80, G28) 320 d xDrive 2018-2020BMW 3 (G20, G80, G28) 320 e Plug-in Hybrid Since 2020BMW 3 (G20, G80, G28) 320 i Since 2019BMW 3 (G20, G80, G28) 320 i 1.6 Since 2019BMW 3 (G20, G80, G28) 320 i xDrive Since 2019BMW 3 (G20, G80, G28) 330 d Since 2019BMW 3 (G20, G80, G28) 330 d Mild-Hybrid Since 2020BMW 3 (G20, G80, G28) 330 d Mild-Hybrid xDrive Since 2020BMW 3 (G20, G80, G28) 330 d xDrive Since 2019BMW 3 (G20, G80, G28) 330 e Plug-in Hybrid Since 2019BMW 3 (G20, G80, G28) 330 e Plug-in Hybrid xDrive Since 2020BMW 3 (G20, G80, G28) 330 i Since 2018BMW 3 (G20, G80, G28) 330 i xDrive Since 2018BMW 3 (G20, G80, G28) M 340 i xDrive Since 2019BMW 3 (G20, G80, G28) M340 d Mild-Hybrid xDrive Since 2020
Rear wing Carbon | fits Lamborghini Huracan | Vorsteiner
€4,164.00*
The Vorsteiner carbon rear wing for Lamborghini Huracan Novara Edizione provides more downforce on the rear axle.But the wing is not only impressive in functional terms. The wing also sets new standards visually! The aluminium feet are included in the scope of delivery.
Made from autoclaved prepreg carbon fibre.Expertise: Material certificate
Compatible vehicles:LAMBORGHINI HURACÁN 5.2 LP 580-2 2015-2019LAMBORGHINI HURACÁN 5.2 LP 610-2 Since 2020LAMBORGHINI HURACÁN 5.2 LP 610-4 Since 2014LAMBORGHINI HURACÁN SPYDER 5.2 LP 580-2 Since 2016LAMBORGHINI HURACÁN SPYDER 5.2 LP 610-4 Since 2015