Free shipping
info@aulitzkytuning.de
+49 (0)9874 6891630

KW V1 coilover suspension inox | fits Audi RS4 quattro B5 | 10210021

€0.00*

Delivery time: Availability on request at Aulitzky Tuning*

Optional: Installation on site at Aulitzky Tuning

- Installation and removal of coilover suspension
- Wheel camber correction kit
- Wheel alignment
- Calibration of assistance systems/lights
- Individual suspension tuning according to customer requirements
- Individual test drive and adjustment together with the customer

Assembly at location DE-91564 Neuendettelsau
Reset choice
€0.00*
Product number: KW10210021
Product information "KW V1 coilover suspension inox | fits Audi RS4 quattro B5 | 10210021"

KW V1 coilover suspension

Sportiness paired with outstanding looks. With factory pre-configured damping.
Our entry-level model for more driving pleasure through an appealing and individually adjustable lowering is the KW V1 coilover suspension in the KW typical "inox-line". Thanks to its high-quality workmanship, the consistent use of stainless steel struts, corrosion-resistant springs and harmonised components, it stands for many years of driving pleasure - and not just for the life of the car.

Stepless lowering
The KW V1 enables maximum lowering within the tested adjustment range. This varies depending on the vehicle model and can, for example, be between 30 and 70 millimetres or 50 to 90 millimetres for an individual lowering. Thanks to the dirt-resistant trapezoidal thread and the polyamide threaded ring, the stepless lowering can be varied quickly and easily even years later. Depending on the vehicle, the lowering is carried out either on the wheel-guiding KW stainless steel suspension struts or on the rear axle height adjustment for non-wheel-guiding double-wishbone rear axles.

The benchmark for sporty, dynamic tuning fans
With its harmonious basic set-up for sporty driving on the road, the KW V1 convinces the discerning tuning fan. Our development engineers determine a specific damper set-up and spring rate for each vehicle in order to increase your driving pleasure with the optimum balance of sportiness and suitability for everyday use. After all, you are not buying just any coilover suspension, but a KW coilover suspension that has been specially developed and tuned for your vehicle type. As a manufacturer, KW only uses its own resources, high-quality components and the same damper technology as mass-produced manufacturers. With the KW V1, the rolling and rolling movements of the vehicle body are reduced during compression, allowing you to benefit from unadulterated directness and sportier handling when driving.

Our experience for your driving pleasure
As a manufacturer of customised suspension solutions for road and racing, we have been the market leader and innovation driver for over 25 years. No matter where in the world, sporty drivers, car manufacturers and tuners rely on our KW coilovers "Made in Germany". Every KW coilover suspension is subjected to extensive load tests during production and is developed and manufactured directly at our company headquarters in Fichtenberg, Swabia, in order to fulfil the high standards of our KW quality management. As a German manufacturer, it is a matter of course for us to provide a multi-year warranty on our KW coilover suspension kits, which exceed OEM quality and cover over 4,600 applications. When installed by one of our KW specialist dealers, this warranty is valid for up to five years.

- Optimally adjusted in advance
- sporty and harmonious damping technology
- Stainless steel technology "inox-line"
- Individually height-adjustable
- Tested adjustment range
- Ready-to-install complete solution
- High-quality components for a long service life
- Complete documentation for easy handling

Setup - factory pre-configured damping setup
The KW V1 has a vehicle-specific, permanently configured damper setup. The spring and the damper are perfectly matched to each other so that you experience an optimum balance of sportiness and suitability for everyday use when driving.

Even with a full payload and maximum axle loads, the dampers always work with a sporty characteristic curve. The KW V1 is particularly interesting for tuning enthusiasts who prioritise the show & shine concept.

Please note the conditions and instructions for this product:
- VA + HA height-adjustable (threaded struts)
- With variant 2 or variant 3, hardness adjustment also possible on the VA only when removed!

Technical information:
Lowering VA/HA (mm): 10-30/10-30
Version: V1
Hardness adjustment: none
Material: stainless steel
Adjustment VA/HA: thread/thread
Approval: parts certificate (§19.3)

Compatible vehicles:
Manufacturer Model Version Body Fuel Performance Displacement Cylinder Drive
AUDI A4 Avant (B5) 8D5, B51 11/1994-12/2002 RS4 quattro station wagon Petrol 280 KW 2671 ccm 6 All-wheel drive

Please enter a valid email address.
Please enter a valid question.
Fields marked with * are mandatory.

There aren't any asked questions yet.
Zuletzt gesehene Produkte

Zuletzt gesehene Produkte

%
Brake upgrade kit 370x35mm perforated | fits Audi R8 (420), RS4 (B7/8E), RS6 (4B/C5) | MOVIT
A powerful brake is one of the most important components in motorsport. With these upgrade kits, the necessary balance of performance, weight and durability has been perfectly combined through the uncompromising selection of materials, so that this product can meet the high demands of extreme automotive applications. To achieve this, MOV'IT has increased the diameter and thickness of the brake discs and used more cross holes. Each pre-cast hole is re-drilled and countersunk to achieve a more favourable flow. The brake disc's optimised DDE ventilation system has an 80% larger surface area compared to other brake discs, resulting in a significant reduction in temperature and wear.Without parts certificate Attention: The conversion means that only rims with at least 19 inches can be fitted! Features: - Upgrade kit front axle, 370mm, 2-piece disc, perforated - Without parts certificate Scope of delivery: - 2x brake disc perforated left/right incl. brake pot - 1x mounting material - 1x installation instructions and running-in instructions Compatible vehicles:Audi R8 (422, 423) 4.2 FSI quattro 309kW / 420PS / 4163cm³ (until 31/08/2009)Audi A4 B7 (8E) RS4 quattro 309kW / 420PS / 4163cm³Audi A6 C5 (4B) RS6 quattro 331kW / 450PS / 4172cm³Audi A6 C5 (4B) RS6 quattro plus 353kW / 480PS / 4172cm³ Notes:When installing the upgrade kit, we always recommend replacing the brake pads, as the use of used pads on new brake discs is not recommended.When installed in our factory, the conversion is carried out exclusively with new brake pads!

€1,425.00* €1,519.00* (6.19% saved)
Tip
Aulitzky Exhaust | ECE rear silencer with flap control | fits BMW 1 Series M (E82) 340hp N54
Facts: - Tailpipes: 4x 89mm black - Material: stainless steel - electric flaps - Made in Germany (Lake Constance) - with/without ECE approval (depending on choice of flap control)* Scope of delivery: - 1x Aulitzky Exhaust rear silencer - 4x tailpipes 89mm black - ECE handout Compatible vehicles:VehicleVehicle typePower outputcubic capacityEngineYear of constructionBMW 1 Series Coupe (E82)M250kW / 340PS2979ccN54 B30 A03.11 - 06.12 *ATTENTION!In conjunction with the standard or ECE flap control system (with type approval), this flap rear silencer has ECE approval so that it can be used legally within the scope of the StVZO without registration in the vehicle documents.The use of flap rear silencers in conjunction with the race flap control (without approval) is not permitted for use on public roads and is only intended for racing purposes! If you nevertheless install a product without approval in your vehicle and use it within the scope of the StVZO, you are liable to prosecution. Possible consequences that you can expect in this case: Expiry of the operating licence in accordance with §19 of the StVZO and possible resulting immobilisation of the vehicle. Other possible consequences, such as a charge of tax evasion, as well as possible investigations by the environmental authorities are at the discretion of the investigators.

€3,679.00*
Tip
Aulitzky Exhaust | ECE downpipe with sports catalyst | fits BMW X5 40i (G05) OPF
Facts: - 4.49“ (114mm) > 3” (76mm), replaces the main catalyst - with 200 cell HJS stainless steel sports catalyst - Euro 6 compatible - for current OPF models - with Thermo-Integral insulation (for an extra charge) - with ECE approval* Compatible vehicles: VehicleVehicle typePowerEngine capacityEngine typeYear of constructionBMW X5 (G05)xDrive 40i OPF250kW / 340hp2998cm³B58 B30 C08.18 - Note: Depending on the software version, the engine control light may light up. We recommend the purchase of an OFF set module or software customisation. *This downpipe has ECE approval so that it can be used within the scope of the German Road Traffic Licensing Regulations (StVZO) without registration in the vehicle documents.

From €2,256.00*
Brake pads ME22 4-piston front axle | fits BMW M2/M3/M4/x35i/x45i (F87/F80/F82/F83/F2x/F3x) | Endless
The Endless pads are an excellent brake pad for racing and everyday use. The ME22 is the further development of the popular ME20 brake pad. In contrast to the MX72 pad, the ME22 has no heat protection plates.Coefficient of friction 0.36 - 0.42 µOperating temperature 150 - 800 °CSemi-metallic pad For the front axle. Compatible vehicles:BMW 4-piston BMW (Performance) brake caliper, blue caliper on F-series vehicles, such as M135i M140i F20 F21, M235i M240i F22 F23, 335i 340i F30 F31 F34, 435i 440i F32 F33 F36, M2 F87, M3 F80,M4 F82 F83Alpina models such as the B3 Motorsport articles - without STVZO approval.

€450.00*
Tip
Aulitzky Exhaust | ECE flap exhaust system 3” (76mm) from OPF | fits Toyota Yaris 1.6 GR (P21) 261hp
Facts: - Stainless steel 3 inch (76mm) exhaust system from OPF - tailpipe trims black 101mm - electric flaps - Made in Germany (Lake Constance) - Plug & Play - with ECE approval* Scope of delivery: - 1x Aulitzky Exhaust exhaust system from OPF - Tailpipes of your choice - ECE handout Compatible vehicles:VehicleVehicle typePowerEngine capacityEngineYear of constructionToyota Yaris (P21)1.6 GR 4WD192kW / 261hp1618cm³G16E-GTS02.20 - *This flap exhaust system has ECE approval so that it can be used legally within the scope of the StVZO without registration in the vehicle documents.

€2,899.00*
Competition intercooler kit EVO 2 | fits Porsche 911 (997.2) 3.6 Turbo 500hp 530hp | Wagner Tuning
The Wagner Tuning Competition intercooler kit EVO2 Upgrade Kit fits the following models:Porsche 997 Turbo (2008+) 3,8L;368KW / 500hp facelift models onlyPorsche 997 Turbo S (2008+) 3,8L;390KW / 530hp facelift models only EVO 2 high-performance intercooler kit: The ultimate performance upgrade for your Porsche 997 Turbo Experience the unbridled power of your Porsche 997 Turbo with our EVO 2 High Performance Intercooler Kit. Here's what this kit has to offer. Our EVO 2 high performance intercoolers (2 x [330mm x 222mm x 145mm] = 21.244cm³) are designed to provide a whopping 77% more charge air volume than the factory intercoolers. This means a significant increase in the performance of your vehicle. Our specially developed competition high performance mesh ensures excellent cooling characteristics. Even under extreme conditions, your engine will maintain the optimum temperature. Despite its impressive performance, our intercooler kit is surprisingly light. Each of the two coolers weighs just 2 x 6.7 kg, which helps to reduce weight in addition to increasing performance. CAD-developed free-form end boxes made of cast aluminum ensure the best possible internal air flow and a high pressure resistance of up to 6 bar (tested). Our kit includes a custom-fit carbon air duct which ensures that the intercooler is optimally supplied with fresh air. This is crucial for the maximum performance of your vehicle. The kit includes additional silicone hoses with an enlarged cross-section to optimize the airflow. Our intercoolers are coated with an anti-corrosion coating that not only ensures longevity, but also has excellent heat conduction properties. Our kit comes complete with new carbon air guides, silicone hoses and aluminum adapters. Installation is simple and is done in exchange for the factory intercoolers. This kit is specifically designed for racing and features a 70mm inlet and outlet for maximum performance. Get the most out of your Porsche 997 Turbo with our EVO 2 high performance intercooler kit. Visit our website for more information and to order your kit. Advantages of the Wagner Tuning intercooler:- improved cooling performance- 77% more charge air volume- extended to 70 mm inlet and outlet- Precisely fitting carbon air duct- simple replacement Scope of delivery:2 intercoolers4 carbon air ducts4 silicone hoses4 hose clamps1 mounting materialAttention: Not approved in the area of the StVZO.

€3,440.00*