Lowering springs Pro-Kit Performance VA+HA 20mm | fits BMW Z4 M40i (G29) B58 | Eibach

Plug and Play suitable for the following models with the B48 & B58.1 engine:BMW 1 Series F20/F21 LCI from 09/2015 - 120i, 125i, M140(x)iBMW 2 Series F22/F23 LCI from 09/2016 - 220i, 230i, M240iBMW 3 Series F30/F31/F34/F35 LCI from 09/2014 - 320i, 330i, 340iBMW 4 Series F32/F33/F36 LCI from 03/2016 - 420i, 430i, 440i The 2.0 liter B48B20 and 3.0 liter B58B30M0 turbo engine of the specified models is equipped with an indirect charge air cooling circuit. This means that the charge air is not cooled using the ambient air as a cooling medium (as usual), but by means of a separate cooling water circuit. A reduction in the cooling water temperature can therefore be directly equated with an improved cooling performance of the charge air. This is precisely where the advantages of the WAGNERTUNING upgrade water cooler come into play. The newly developed competition racing mesh of the WAGNERTUNING high-performance water cooler increases the radiator volume of the standard water cooler by 117%. The ratio between the inner and outer cooling surface generates maximum heat transfer and at the same time allows the adjacent components (e.g. the engine water cooler located behind it) sufficient air flow for heat exchange. Furthermore, the increased cooling water volume allows the entire system thermal to be kept at a lower level over a longer period of time. All WAGNER TUNING water coolers are equipped with a thermally conductive anti-corrosion coating to ensure a long-lasting cooling effect. Installation of the system is also uncomplicated and plug & play with the help of our installation instructions. OEM water cooler dimensions:576 mm x 495 mm x 27 mmV = 7.70 litersA = 2851 cm² WT water cooler dimensions:524 mm x 468 mm x 68 mmV = 16.70 litersA = 2454 cm²Attention: Not approved in the area of the StVZO.

KW V3 Clubsport coilover suspension incl. support bearing With an uncompromising technology transfer from racing to the road, the KW Clubsport coilovers convince.The KW Clubsport coilovers convince with their uncompromising combination of high-end racing technology with maintenance-free KW original equipment components and expertises.This gives you the ideal accessories to realise the full potential of your sports car at trackdays, sports driver training courses, tourist drives on Grand Prix circuits and on the Nürburgring Nordschleife. Developed for the toughest racetrack in the world: the Nürburgring NordschleifeEven in their basic set-up, KW Clubsport coilovers are tuned to the different track surfaces, steep bends, jumps and chicanes of the 20.8 kilometre long Nürburgring Nordschleife. After all, as one of the most successful suspension manufacturers and suppliers in motorsport, we are at home on the Nordschleife.In the VLN Endurance Championship alone, we equip over 70 racing teams and, as a suspension manufacturer, have supported six overall victories at the ADAC Zurich 24h Race Nürburgring in ten years. The winner of the ADAC GT Masters 2011 also relies on our racing expertise, from which the KW Clubsport coilovers benefit.The basic setup of the KW V3 Clubsport and KW V4 Clubsport with separate expansion tank, which is perfectly adapted to the Nordschleife, allows you to adjust your sports car even more individually to the desired sports tyre setup thanks to the numerous adjustment options.In addition to optionally available adjustable support mounts, the KW Clubsport coilovers allow you to adjust the damper forces independently in the rebound and compression stages with the integrated KW V3 Clubsport coilover suspension technology like in racingWith the adjustment wheels for the rebound adjustment, you can fine-tune the recommended basic setup for your sports car and your individually installed performance components with 16 exact clicks. This allows you to directly influence changed wheel loads, for example to influence bodywork movements. Separate from the rebound adjustment, the KW V3 Clubsport allows you to adjust the compression damping to your requirements, such as the sports tyres used, with twelve precise clicks in the low-speed range.These setting options allow you to consider individual setups to suit the vehicle weight, sports tyre characteristics, track characteristics and operating conditions. - Freely adjustable damping technology in rebound and compression damping- Stainless steel technology "inox-line"- Stepless lowering- Tested adjustment range- high-quality components for a long service life- Adjustable rebound damping with 16 exact clicks- Adjustable compression damping with 12 exact clicks- unique, independently acting damping force adjustment- optionally available with aluminium Unibal support bearing. Setup: Application range and damper tuningThe KW V3 Clubsport coilover suspensions impress with their vehicle-specific setup for trackday events on the Nürburgring Nordschleife as well as the possibility of quickly tuning these suspensions on other racetracks and on individual performance sports cars. Please note the conditions and instructions for this product:- VA + HA height-adjustable (VA coilover struts, HA springs with height adjustment + dampers)- Vehicles with electronic damper control must be decommissioned. Vehicle-specific KW decommissioning kits can be found in the accessories table.- The dampers have easy-to-operate adjustment wheels. Due to the design, the rebound stage can only be adjusted if the piston rod is accessible.- Clubsport suspension with support bearing: only available with VA support bearing Technical information:Lowering VA/HA (mm): 30-50/25-55Version: V3 ClubsportHardness adjustment: Rebound and compression dampingMaterial: Stainless steelAdjustment VA/HA: thread/threadApproval: Parts certificate (§19.3) Compatible vehicles:Manufacturer Model Version Body Fuel Performance Displacement Cylinder DriveFORD FOCUS III (DYB_) 07/2010- 2.3 RS AWD Hatchback Petrol 257 KW 2261 ccm 4 All-wheel drive

KW V1 coilover suspension Sportiness paired with outstanding looks. With factory pre-configured damping.Our entry-level model for more driving pleasure through an appealing and individually adjustable lowering is the KW V1 coilover suspension in the KW typical "inox-line". Thanks to its high-quality workmanship, the consistent use of stainless steel struts, corrosion-resistant springs and harmonised components, it stands for many years of driving pleasure - and not just for the life of the car. Stepless loweringThe KW V1 enables maximum lowering within the tested adjustment range. This varies depending on the vehicle model and can, for example, be between 30 and 70 millimetres or 50 to 90 millimetres for an individual lowering. Thanks to the dirt-resistant trapezoidal thread and the polyamide threaded ring, the stepless lowering can be varied quickly and easily even years later. Depending on the vehicle, the lowering is carried out either on the wheel-guiding KW stainless steel suspension struts or on the rear axle height adjustment for non-wheel-guiding double-wishbone rear axles. The benchmark for sporty, dynamic tuning fansWith its harmonious basic set-up for sporty driving on the road, the KW V1 convinces the discerning tuning fan. Our development engineers determine a specific damper set-up and spring rate for each vehicle in order to increase your driving pleasure with the optimum balance of sportiness and suitability for everyday use. After all, you are not buying just any coilover suspension, but a KW coilover suspension that has been specially developed and tuned for your vehicle type. As a manufacturer, KW only uses its own resources, high-quality components and the same damper technology as mass-produced manufacturers. With the KW V1, the rolling and rolling movements of the vehicle body are reduced during compression, allowing you to benefit from unadulterated directness and sportier handling when driving. Our experience for your driving pleasureAs a manufacturer of customised suspension solutions for road and racing, we have been the market leader and innovation driver for over 25 years. No matter where in the world, sporty drivers, car manufacturers and tuners rely on our KW coilovers "Made in Germany". Every KW coilover suspension is subjected to extensive load tests during production and is developed and manufactured directly at our company headquarters in Fichtenberg, Swabia, in order to fulfil the high standards of our KW quality management. As a German manufacturer, it is a matter of course for us to provide a multi-year warranty on our KW coilover suspension kits, which exceed OEM quality and cover over 4,600 applications. When installed by one of our KW specialist dealers, this warranty is valid for up to five years. - Optimally adjusted in advance- sporty and harmonious damping technology- Stainless steel technology "inox-line"- Individually height-adjustable- Tested adjustment range- Ready-to-install complete solution- High-quality components for a long service life- Complete documentation for easy handling Setup - factory pre-configured damping setupThe KW V1 has a vehicle-specific, permanently configured damper setup. The spring and the damper are perfectly matched to each other so that you experience an optimum balance of sportiness and suitability for everyday use when driving. Even with a full payload and maximum axle loads, the dampers always work with a sporty characteristic curve. The KW V1 is particularly interesting for tuning enthusiasts who prioritise the show & shine concept. Please note the conditions and instructions for this product: - VA + HA height-adjustable (VA coilover struts, HA springs with height adjustment + damper) Technical info: Lowering VA/HA (mm): 10-40/10-40 Version: V1 Hardness adjustment: none Material: stainless steel Adjustment VA/HA: thread/thread Approval: parts certificate (§19.3) Compatible vehicles: Manufacturer Model Version Body Fuel Performance Displacement Cylinder Drive FORD FOCUS I (DA1, DAW, DB1, DBW, DBY) 09/1998-11/2009 RS Hatchback Petrol 158 KW 1988 ccm 4 Front-wheel drive

Facts: - Tailpipes: 89mm black matt - 3.0 inch stainless steel exhaust system from OPF - Electric flaps - Flap control still possible via the driving profiles (only with AMG Performance AGA) - Made in Germany (Lake Constance) - with/without ECE approval (depending on choice of flap control)* Scope of delivery: - 1x Aulitzky exhaust system from OPF - 89mm tailpipes black matt - ECE handout Compatible vehicles: VehicleVehicle typePower outputcubic capacityEngineYear of constructionMerceds-Benz G-Class (W463)AMG G63430kW / 585PS3982ccM 177.98003.18 - *ATTENTION! In conjunction with the standard or ECE flap control system (with type approval), this flap exhaust system has ECE approval so that it can be used legally within the scope of the StVZO without registration in the vehicle documents.The use of flap exhaust systems in conjunction with the race flap control (without approval) is not permitted for use on public roads and is only intended for racing purposes! If you nevertheless install a product without approval in your vehicle and use it within the scope of the StVZO, you are liable to prosecution. Possible consequences that you can expect in this case: Expiry of the operating licence in accordance with §19 of the StVZO and possible resulting immobilisation of the vehicle. Other possible consequences, such as a charge of tax evasion, as well as possible investigations by the environmental authorities are at the discretion of the investigators.

Plug and Play suitable for the following models with the B48 & B58.1 engine:BMW 1 Series F20/F21 LCI from 09/2015 - 120i, 125i, M140(x)iBMW 2 Series F22/F23 LCI from 09/2016 - 220i, 230i, M240iBMW 3 Series F30/F31/F34/F35 LCI from 09/2014 - 320i, 330i, 340iBMW 4 Series F32/F33/F36 LCI from 03/2016 - 420i, 430i, 440i The 2.0 liter B48B20 and 3.0 liter B58B30M0 turbo engine of the specified models is equipped with an indirect charge air cooling circuit. This means that the charge air is not cooled using the ambient air as a cooling medium (as usual), but by means of a separate cooling water circuit. A reduction in the cooling water temperature can therefore be directly equated with an improved cooling performance of the charge air. This is precisely where the advantages of the WAGNERTUNING upgrade water cooler come into play. The newly developed competition racing mesh of the WAGNERTUNING high-performance water cooler increases the radiator volume of the standard water cooler by 117%. The ratio between the inner and outer cooling surface generates maximum heat transfer and at the same time allows the adjacent components (e.g. the engine water cooler located behind it) sufficient air flow for heat exchange. Furthermore, the increased cooling water volume allows the entire system thermal to be kept at a lower level over a longer period of time. All WAGNER TUNING water coolers are equipped with a thermally conductive anti-corrosion coating to ensure a long-lasting cooling effect. Installation of the system is also uncomplicated and plug & play with the help of our installation instructions. OEM water cooler dimensions:576 mm x 495 mm x 27 mmV = 7.70 litersA = 2851 cm² WT water cooler dimensions:524 mm x 468 mm x 68 mmV = 16.70 litersA = 2454 cm²Attention: Not approved in the area of the StVZO.

KW V1 coilover suspension Sportiness paired with outstanding looks. With factory pre-configured damping.Our entry-level model for more driving pleasure through an appealing and individually adjustable lowering is the KW V1 coilover suspension in the KW typical "inox-line". Thanks to its high-quality workmanship, the consistent use of stainless steel struts, corrosion-resistant springs and harmonised components, it stands for many years of driving pleasure - and not just for the life of the car. Stepless loweringThe KW V1 enables maximum lowering within the tested adjustment range. This varies depending on the vehicle model and can, for example, be between 30 and 70 millimetres or 50 to 90 millimetres for an individual lowering. Thanks to the dirt-resistant trapezoidal thread and the polyamide threaded ring, the stepless lowering can be varied quickly and easily even years later. Depending on the vehicle, the lowering is carried out either on the wheel-guiding KW stainless steel suspension struts or on the rear axle height adjustment for non-wheel-guiding double-wishbone rear axles. The benchmark for sporty, dynamic tuning fansWith its harmonious basic set-up for sporty driving on the road, the KW V1 convinces the discerning tuning fan. Our development engineers determine a specific damper set-up and spring rate for each vehicle in order to increase your driving pleasure with the optimum balance of sportiness and suitability for everyday use. After all, you are not buying just any coilover suspension, but a KW coilover suspension that has been specially developed and tuned for your vehicle type. As a manufacturer, KW only uses its own resources, high-quality components and the same damper technology as mass-produced manufacturers. With the KW V1, the rolling and rolling movements of the vehicle body are reduced during compression, allowing you to benefit from unadulterated directness and sportier handling when driving. Our experience for your driving pleasureAs a manufacturer of customised suspension solutions for road and racing, we have been the market leader and innovation driver for over 25 years. No matter where in the world, sporty drivers, car manufacturers and tuners rely on our KW coilovers "Made in Germany". Every KW coilover suspension is subjected to extensive load tests during production and is developed and manufactured directly at our company headquarters in Fichtenberg, Swabia, in order to fulfil the high standards of our KW quality management. As a German manufacturer, it is a matter of course for us to provide a multi-year warranty on our KW coilover suspension kits, which exceed OEM quality and cover over 4,600 applications. When installed by one of our KW specialist dealers, this warranty is valid for up to five years. - Optimally adjusted in advance- sporty and harmonious damping technology- Stainless steel technology "inox-line"- Individually height-adjustable- Tested adjustment range- Ready-to-install complete solution- High-quality components for a long service life- Complete documentation for easy handling Setup - factory pre-configured damping setupThe KW V1 has a vehicle-specific, permanently configured damper setup. The spring and the damper are perfectly matched to each other so that you experience an optimum balance of sportiness and suitability for everyday use when driving. Even with a full payload and maximum axle loads, the dampers always work with a sporty characteristic curve. The KW V1 is particularly interesting for tuning enthusiasts who prioritise the show & shine concept. Please note the conditions and instructions for this product: - VA + HA height-adjustable (threaded struts) - With variant 2 or variant 3, hardness adjustment also possible on the VA only when removed! Technical information: Lowering VA/HA (mm): 10-30/10-30 Version: V1 Hardness adjustment: none Material: stainless steel Adjustment VA/HA: thread/thread Approval: parts certificate (§19.3) Compatible vehicles: Manufacturer Model Version Body Fuel Performance Displacement Cylinder Drive AUDI A4 Avant (B5) 8D5, B51 11/1994-12/2002 RS4 quattro station wagon Petrol 280 KW 2671 ccm 6 All-wheel drive