AutoTecknic | Carbon steering wheel trim | BMW M2/M3/M4/M5/M6/X5M/X6M incl. Competition/CS/GTS (F-Series)

Suitable for the following models:BMW 2 Series (F22) CoupeM2 (F87) Aerodynamically very efficient wing for the BMW 2 Series (F22) and M2 (F87). The wing can be adjusted in three stages to adapt to different routes. Adjustment takes seconds and requires no tools. Objective: Stabilizes straight-line stability and cornering at high speeds. - made of cnc-milled aluminium parts and high-quality carbon- finish: visible carbon polished | aluminium black anodized- three-stage adjustable- incl. mounting material- easy to install- very good visibility through the interior mirror- suitable for registration

Suitable for the following models: BMW 2 Series (F22) Coupe M2 (F87) Aerodynamic wing for the BMW 2 Series (F22) and M2 (F87). The wing can be adjusted in three stages to adapt to different routes. Adjustment takes seconds and requires no tools. Objective: Stabilises straight-line stability and cornering at high speeds. - Made from cnc-milled aluminium parts and high-quality carbon - Finish: polished visible carbon | black anodised aluminium - three-way adjustable - incl. mounting material - very easy to fit - with ABE

Suitable for the following models (only in conjunction with the Airconcept rear wing): BMW 2 Series (F22) Coupe M2 (F87) BMW 4 Series (F32) Coupe M4 (F82) Increases the position of the wing by 125 mm. Objective: real trackday tool! - made from cnc-milled aluminium - the wing remains adjustable in three stages - installation and adjustment in seconds without tools - registration capable!

With the AP-Racing Big Brake Kit, we offer a high-performance solution especially for track days and for race track drivers. The friction rings are mounted floating on the high-strength, milled aluminium pots. The advantages of this are, on the one hand, the lower weight and, on the other, the fact that the friction rings can be replaced cost-effectively when they wear out. The AP-Racing calipers are racing calipers without dust boots, which are only recommended for use on the racetrack (regular cleaning of the calipers is necessary in normal road traffic). Details and scope of delivery:- Big Brake Kit for the front/rear axle, consisting of AP Racing calipers and J-Hook brake discs in 378×34mm- AP Racing 6-piston brake caliper- Brake discs 378×34mm, J-Hook- CNC milled brake caliper adapter incl. material certificate- Braided steel brake lines- incl. brake padsAluminium pots and floating mounting Compatible vehicles:- BMW F87 M2 incl. Competition/CS- BMW F8x M3/M4 incl. Competition NOTES:If we do not expressly refer to a parts certificate or general operating licence (ABE) in the product text, this is a motorsport article that is not approved in the German Road Traffic Regulations (StVZO) and therefore the operating licence expires if no registration is made in accordance with § 21 StVO!This brake system can only be registered by us after special tests. Please note that vehicle spare parts should only be installed by a qualified specialist workshop in order to ensure that they function properly and that the vehicle is roadworthy.

Facts: - Tailpipes: 4x101mm black matt - stainless steel 3 inch (76mm) - Electric flaps - Exhaust flaps with ceramic bearings - Made in Germany (Lake Constance) - with ECE approval * Scope of delivery: - 1x Aulitzky Exhaust exhaust system from OPF - 4x tailpipes 101mm black matt - ECE handoutCompatible vehicles:VehicleTypePower outputcubic capacityEngineYear of constructionBMW 2 Series Coupe (F87)M2 Competition302kW / 411PS2979ccS55 B30 A06.18 - 06.21BMW 2 Series Coupe (F87)M2 CS331kW / 450PS2979ccS55 B30 A11.19 - 06.21 *The combination certificate is available (includes Intakte, intercooler, boost / charge pipe kit, downpipe, exhaust system, 560hp Aulitzky App performance increase and 95dB increase in stationary noise).In conjunction with the standard or ECE flap control system (with type approval), this flap exhaust system has ECE approval so that it can be used legally within the scope of the StVZO without registration in the vehicle documents.

Function: - Variable flap control of the original or retrofitted flap exhaust system - Can be controlled via steering wheel buttons Compatible vehicles:VehicleVehicle typePowerEngine capacityEngineYear of constructionBMW 2er Coupe (F87)M2272kW / 370hp2979cm³N55 B30 A11.15 - 06.18BMW 2er Coupe (F87)M2 Competition302kW / 411hp2979cm³S55 B30 A06.18 - 06.21BMW 2er Coupe (F87)M2 CS331kW / 450hp2979cm³S55 B30 A11.19 - 06.21 Note: This product is NOT approved in the StVZO and is NOT intended for sale within the EU! This item is intended exclusively for show and motorsport purposes and must not be used/installed on public roads. If the component is installed on/in the vehicle, the operating license expires!The pictures shown are examples.

This BMW M2 Competition (F87) in the colour Alpine White is for sale. The vehicle still has a BMW warranty until 09.2025! The BMW is fully serviced and is currently in second hand.Vehicle is accident-free and a German model. The following work was carried out at BMW in September 2023 (at 83,000km)-Brake front and rear complete-Large customer service-MOT until 09.2025-Michelin Pilot Sport 4S front and rear axle new The M2 also has the following equipment/optimisations:-Harman Kardon sound system-Apple CarPlay-Sports seats-Trackpack-Sliding roof-KW V3 coilover suspension (4000km old)-Aulitzky Exhaust New Generation exhaust system (NEW!)-Custom downpipes-Software optimisation to approx. 530hp Custom Map-Carbon front lip in GT4 style-Track plates on front and rear axle-OEM rims painted black-Burkhardt Engineering GT4 wings-Roof black foiled The M2 has never been driven on a race track or similar.The car is currently still registered, but will only be handed over deregistered. If you are seriously interested and/or have any questions, please do not hesitate to contact us.

AutoTecknic carbon gearshift surround with Alcantara for BMW F87 M2 Competition Compatible vehicles:BMW 2 Coupe (F22, F87) M2 Competition 2018-2021

AutoTecknic carbon seat cover suitable for F80 M3 | F82 M4 | F87 M2 Competition Compatible vehicles:BMW 2 Coupe (F22, F87) M2 Competition 2018-2021BMW 3 (F30, F80) M3 2014-2018BMW 3 (F30, F80) M3 CS 2018-2018BMW 3 (F30, F80) M3 Competition 2016-2018BMW 4 Convertible (F33, F83) M4 2014-2020BMW 4 Convertible (F33, F83) M4 Competition 2016-2020BMW 4 Coupe (F32, F82) M4 2014-2020BMW 4 Coupe (F32, F82) M4 CS 2017-2019BMW 4 Coupe (F32, F82) M4 Competition 2016-2020BMW 4 Coupe (F32, F82) M4 GTS 2016-2019

AutoTecknic carbon steering wheel trim suitable for F80 M3 | F82 M4 | F10 M5 LCI | F06 / F12 / F13 M6 Compatible vehicles:BMW 2 Coupe (F22, F87) M2 2015-2018BMW 2 Coupe (F22, F87) M2 CS 2019-2021BMW 2 Coupe (F22, F87) M2 Competition 2018-2021BMW 3 (F30, F80) M3 2014-2018BMW 3 (F30, F80) M3 CS 2018-2018BMW 3 (F30, F80) M3 Competition 2016-2018BMW 4 Convertible (F33, F83) M4 2014-2020BMW 4 Convertible (F33, F83) M4 Competition 2016-2020BMW 4 Coupe (F32, F82) M4 2014-2020BMW 4 Coupe (F32, F82) M4 CS 2017-2019BMW 4 Coupe (F32, F82) M4 Competition 2016-2020BMW 4 Coupe (F32, F82) M4 GTS 2016-2019BMW 5 (F10) M5 2011-2016BMW 5 (F10) M5 30th Anniversary 2014-2016BMW 5 (F10) M5 Competition 2013-2016BMW 6 Convertible (F12) M6 2012-2018BMW 6 Convertible (F12) M6 Competition 2013-2015BMW 6 Convertible (F12) M6 Competition 2015-2018BMW 6 Coupe (F13) M6 2012-2017BMW 6 Coupe (F13) M6 Competition 2013-2015BMW 6 Coupe (F13) M6 Competition 2015-2017BMW 6 Gran Coupe (F06) M6 2013-2018BMW 6 Gran Coupe (F06) M6 Competition 2013-2015BMW 6 Gran Coupe (F06) M6 Competition 2015-2018BMW X5 (F15, F85) M 2014-2018BMW X6 (F16, F86) M 2014-2019

Autotecknic dry carbon fibre diffuser for BMW 2 Series F87 M2 & M2 Competition Compatible vehicles:BMW 2 Coupe (F22, F87) M2 2015-2018BMW 2 Coupe (F22, F87) M2 Competition 2018-2021

Looking to add a little more kick to your interior? Look no further, because we've just released our replacement bright red M1/M2 buttons for select BMW F-Series vehicles. These buttons are manufactured from precision ABS plastic and finished with a hardwearing, UV and scratch resistant clear coat to ensure a long life in everyday use. Please note that this product is only suitable for M-series vehicles (see example image). Compatible vehicles:BMW 2 Coupe (F22, F87) M2 2015-2018BMW 2 Coupe (F22, F87) M2 CS 2019-2021BMW 2 Coupe (F22, F87) M2 Competition 2018-2021BMW 3 (F30, F80) M3 2014-2018BMW 3 (F30, F80) M3 CS 2018-2018BMW 3 (F30, F80) M3 Competition 2016-2018BMW 4 Convertible (F33, F83) M4 2014-2020BMW 4 Convertible (F33, F83) M4 Competition 2016-2020BMW 4 Coupe (F32, F82) M4 2014-2020BMW 4 Coupe (F32, F82) M4 CS 2017-2019BMW 4 Coupe (F32, F82) M4 Competition 2016-2020BMW 4 Coupe (F32, F82) M4 GTS 2016-2019BMW 5 (F10) M5 2011-2016BMW 5 (F10) M5 30th Anniversary 2014-2016BMW 5 (F10) M5 Competition 2013-2016BMW 6 Convertible (F12) M6 2012-2018BMW 6 Convertible (F12) M6 Competition 2013-2015BMW 6 Convertible (F12) M6 Competition 2015-2018BMW 6 Coupe (F13) M6 2012-2017BMW 6 Coupe (F13) M6 Competition 2013-2015BMW 6 Coupe (F13) M6 Competition 2015-2017BMW 6 Gran Coupe (F06) M6 2013-2018BMW 6 Gran Coupe (F06) M6 Competition 2013-2015BMW 6 Gran Coupe (F06) M6 Competition 2015-2018

Your BMW is missing a data display! We have the CANchecked display for BMW F-series incl. M2 M3 M4 (F21, F22, F23, F30, F31, F32, F33, F80, F82, F83 and F87).Naturally also fits the M models (M2, M3, M4). Access to all data from the engine:The sensors are queried directly via Can Bus and are displayed on our tried-and-tested MFD28. The display for the BMW E-series comes with a vehicle-specific cover and fits into the interior like an original part. This means that the ventilation through the slots remains intact. Our display emulates a manufacturer tester so that all detailed values are available. We have optimized the protocol to achieve maximum polling speed. Details:- integrates perfectly into the vehicle interior- Up to 128 sensors can be queried- 10 individually configurable views with our DSS - Display Setup Software- ready-made views for a quick start with our display- simply plug and play via our cable set - plug in, done- 4 additional analog inputs for exhaust gas temperature, oil pressure and more- Best readability - optional anti-reflective film included- Query the sensors like manufacturer diagnostic tools Performance meter:Measure your acceleration times in our performance widget - 0-100, 100-200, 0-200 Data jogging:Log all data to the internal SD card. Whether “on-demand” (start at the tap of a finger) or permanently. All data from your last turn is saved. Preset alarms:Preset alerts can be easily activated and customized. For example, receive a large warning message if the exhaust gas temperature is above 900 degrees. 4 additional analog inputs:Additional temperature and/or pressure sensors can be connected for further monitoring options. e.g. exhaust gas temperature or exhaust gas back pressure. An ethanol sensor can be connected to one of the digital inputs. Read out/delete errors:Read out errors from the engine control unit in plain text and also delete them Individual designWhether it's the individual start screen or the selection from a variety of different widgets. Make the display your display! Switch pages with the cruise control button:To make driving safer, we have integrated the cruise control switch here with the company Lightweight-Performance. When cruise control is not active, you can use the up/down button to switch the views in the display. This has the following advantages:- No “searching” for the display while concentrating on the road ahead- Switching even when wearing gloves (on trackdays)- Quick and safe checking of overview pages and then returning to the main view Here is an example video in the BMW F-series. In the E-series, the cruise control lever is separate under the blinker lever. Driver Dynamics:We have developed a special view for all track drivers who want to further improve their driving style and become a second or two faster:- G-forces (lateral and longitudinal acceleration)- Vehicle speed- Steering angle- accelerator pedal position- Brake pressure This sensor system gives the driver the opportunity to aim for even higher speeds in bends and to hit the braking point even later. Together with the data log in the internal memory, which can be downloaded from the display after a track day, this offers a great opportunity to synchronize the data with a video. Access to all data from the engine control unit:We supply your display with a ready-made TRI file as standard. All sensors that are queried are defined here. Temperatures:Engine water temperature, oil temperature, intake temperature, exhaust temperature, transmission temperature Pressures:Boost pressure, boost pressure target, fuel pressure high pressure pump, exhaust back pressure, low pressure, front brake pressure, rear brake pressure, oil pressure Lambda/mixture:Lambda value target/actual, injection correction, long-term lambda adjustment, total ignition angle, ignition angle per cylinder Other data:RPM, air mass (g/s), vehicle speed, throttle angle, battery voltage, gear, accelerator pedal position, longitudinal and lateral acceleration, steering angle, yaw angle, torque, power, boost pressure control valve activation If values are missing, they can easily be added. It always depends on the engine whether it supports the values, sometimes not all sensors are available. Attention: Not all values are available for all engines! For which engines and models is the display for BMW F-series incl. M2 M3 M4:The display fits the following BMW F-series:- 1 Series: F20, F21- 2 Series: F22, F23- 3 Series: F30, F31- 4 Series: F32, F33- M models: F87 (M2), F80 (M3), F82 (M4), F83 (M4 Convertible) We currently support the following engines, unlisted engines can be added on request:- B48- B58- N13- N47- N55- N57- S55 The respective version for RHD (right-hand drive) is also available. The data may vary between the different engines. Read out and delete errors:Swipe down to access the “DTC” (Diagnostic Trouble Codes = fault memory). The display reads the fault memory from the engine. Optionally, you can also delete these directly on the display. Errors for the engine are displayed in plain text so that you can decide for yourself whether you can continue driving. MFD28 Technical data:- Dimensions: 70.3 x 52mm - Hardware: 2.8” TFT screen, touchscreen, MicroSD, MicroUSB- High-quality milled aluminum front frame- Symmetrical display - ideal for rotating it by 90- Views completely freely configurable on the PC with our DSS - Display Setup Software- Up to 64 widgets per display- 64 sensors (Can Bus + internal)- 10 views- 4x analog inputs- Optional external switching flash- Can bus switching- Can Bus protocols: UDS, KWP2000, OBD Supported values:Many customers always ask: “Which values can I query from my control unit”. The answer: “ALL”. Our MFD28 is compatible with ISO 11898-2 and SAE J2284.The control unit manufacturers themselves determine which values are sent via the CAN bus interface. The documentation is important here - possibly even in the form of a DBC file that can be imported directly. You can also access our extensive list of already implemented control units. This can be found in the download area. A total of up to 50 sensors can be queried if the manufacturer supports this.Broadcast data as well as OBD2 queries via Can Bus (11bit/29bit) are implemented. Special protocols such as TP2.0 from VW/Audi and UDS are also available. DSS - Display Setup Software:With our DSS - Display Setup Software, the display can be conveniently configured on the PC. The Can Bus protocol can be customized, you can import DBC files and design the displays with your own widgets.The log viewer downloads log files from the display. These can then be viewed and values can be individually selected and scaled.A built-in Can Bus logger makes it possible to take a close look at the log. This can be used to reverse-engineer unknown Can Buses.

Facts: - Charge- & Boostpipe aluminium black - incl. mounting rubbers, clamps Compatible vehicles:VehicleVehicle typePowerEngine capacityEngine typeYear of construction BMW 3 Series (F80)M3317kW / 431hp2979cm³S55 B30 A03.14 - 10.18 BMW 3 Series (F80)M3 Competition331kW / 450hp2979cm³S55 B30 A03.16 - 10.18 BMW 3 Series (F80)M3 CS338kW / 460hp2979cm³S55 B30 A01.18 - 10.18 BMW 4 Series (F82/F83)M4317kW / 431hp2979cm³S55 B30 A03.14 - 07.20 BMW 4 Series (F82/F83)M4 Competition331kW / 450hp2979cm³S55 B30 A03.16 - 07.20 BMW 4 Series Coupe (F82)M4 CS338kW / 460hp2979cm³S55 B30 A07.17 - 06.19

Includes the following services:- Removing and replacing the connecting rod bearings- Check and measure crankshaft journals- Check and adjust the oil pump- Clean all parts- Wheel alignment- Oil & filter change- incl. all parts such as bearings, screws, seals, oil filter and engine oil (10W60)- Entry in the service booklet with BMW serial number stamp- 1 liter oil refillIn addition, and depending on requirements, we can also replace the spark plugs and engine mounts for an additional charge. Please note:This service can only be carried out at our company headquarters!

Crank Hub Fix incl. working time and the following components:- Oil pan gasket- BMW set of aluminum screws- Valve cover gasket- Camshaft bolts- Chain tensioner sealing ring- Locking cap- Oil filter- Engine oil- incl. Aulitzky crankshaft lock Attention:The Crank Hub Fix is only available from us including installation.Shipping is not offered! Compatible vehicles:VehicleVehicle typePowerEngine capacityEngine typeYear of construction BMW 2er Coupe (F87)M2 Competition302kW / 411hp2979cm³S55 B30 A06.18 - 06.21 BMW 2er Coupe (F87)M2 CS331kW / 450hp2979cm³S55 B30 A11.19 - 06.21 BMW 3er (F80)M3 Competition331kW / 450hp2979cm³S55 B30 A03.16 - 10.18 BMW 4er (F82)M4 Competition331kW / 450hp2979cm³S55 B30 A03.16 - 07.20

Scope of delivery: - Aulitzky tuning crankshaft lock incl. 8 BMW original fastening screws - Fitting instructions Compatible vehicles:VehicleVehicle typePowerEngine capacityEngine typeYear of construction BMW 2er Coupe (F87)M2 Competition302kW / 411hp2979cm³S55 B30 A06.18 - 06.21 BMW 3er (F80)M3317kW / 431hp2979cm³S55 B30 A03.14 - 10.18 BMW 3er (F80)M3 Competition331kW / 450hp2979cm³S55 B30 A03.16 - 10.18 BMW 4er (F82/F83)M4317kW / 431hp2979cm³S55 B30 A03.14 - 07.20 BMW 4er (F82/F83)M4 Competition331kW / 450hp2979cm³S55 B30 A03.16 - 07.20

Indirect charge air cooling is used in the BMW S55 engine. With indirect charge air cooling, the charge air is cooled by a low-temperature coolant circuit. The low-temperature coolant circuit is then cooled again by the drive air via two air-coolant heat exchangers. A reduced cooling water temperature directly improves the cooling performance of the intercooler. The CSF heat exchanger is installed as an upgrade to the original main heat exchanger and is the largest "drop-in-fit" heat exchanger available on the market for the S55 engine. The CSF heat exchanger has a massive 2-row 42 mm double core with 2x 45 rows and CSF's exclusive B-Tube technology. The B-Tube technology alone enables an increase in cooling efficiency of over 15% compared to the traditional O-tube design of the original heat exchanger. As an OEM supplier with state-of-the-art production machinery, CSF is able to install an extremely efficient fin height of only 6.5 mm for maximum surface contact. The dual-pass flow structure allows the coolant to flow through the core of the radiator twice before exiting the radiator for the lowest possible outlet temperature. The frontal cooling surface increases by ~ 27% compared to the original heat exchanger. Equipped with CNC machined "Quick-Connect" inlet/outlet connections as well as CNC machined brackets and fittings, the CSF heat exchanger is a direct replacement for the original radiator. It can be connected directly and easily to all original hoses, and no grilles, covers or other parts need to be cut or modified - making it a 1:1 replacement. Also ideal as a replacement for accident vehicles or vehicles with a defect. (Please note that various modifications to the plastic parts are required to fit the larger, 50-row Race heat exchanger). In addition, the CSF heat exchanger is equipped with a practical drain plug, which the original system does not have! A stone guard is also included in the scope of delivery. This ensures the greatest possible protection against stone chips in the radiator network. Thanks to thermodynamically optimised anti-corrosion vapour deposition, CSF guarantees maximum quality and durability - this is underlined by the lifetime product guarantee. The radiator is available as "polished chrome" or in a plain black colour. Compatible vehicles:BMW 2 Coupe (F22, F87) M2 CS 2019-2021BMW 2 Coupe (F22, F87) M2 Competition 2018-2021BMW 3 (F30, F80) M3 2014-2018BMW 3 (F30, F80) M3 CS 2018-2018BMW 3 (F30, F80) M3 Competition 2016-2018BMW 4 Convertible (F33, F83) M4 2014-2020BMW 4 Convertible (F33, F83) M4 Competition 2016-2020BMW 4 Coupe (F32, F82) M4 2014-2020BMW 4 Coupe (F32, F82) M4 CS 2017-2019BMW 4 Coupe (F32, F82) M4 Competition 2016-2020BMW 4 Coupe (F32, F82) M4 GTS 2016-2019

CSF Race F8X M3 M4 - Top Mount intercooler / with parts certificate! World's first cast end tank intercooler for the BMW S55 engine in the BMW F8x M3 M4.Multiple air splitters are cast into the end tanks on the hot/cold side to optimize airflow through the custom CSF liquid-to-air intercooler core (CFD analysis and testing completed to ensure optimal performance)** 60% larger core size compared to the OEM cooler. Left/right, cross-flow, dual-pass core configuration with 2-stage water cooling for maximum efficiency and inlet temperature reduction (vs. OEM single-pass vertical flow design) Designed with 3D scanning / rapid prototyping technology to ensure precise fit and maximum surface area utilization. “Drop-in fit” design for easy and quick plug-and-play installation. Complete with OEM style “Quick-Connect” water connection and sensor ports.Raw aluminum finish.Also available in a professional “Crinkle Black” powder coat finish.Lifetime Warranty. Compatible vehicles:BMW 2 Coupe (F22, F87) M2 CS 2019-2021BMW 2 Coupe (F22, F87) M2 Competition 2018-2021BMW 3 (F30, F80) M3 2014-2018BMW 3 (F30, F80) M3 CS 2018-2018BMW 3 (F30, F80) M3 Competition 2016-2018BMW 4 Convertible (F33, F83) M4 2014-2020BMW 4 Convertible (F33, F83) M4 Competition 2016-2020BMW 4 Coupe (F32, F82) M4 2014-2020BMW 4 Coupe (F32, F82) M4 CS 2017-2019BMW 4 Coupe (F32, F82) M4 Competition 2016-2020BMW 4 Coupe (F32, F82) M4 GTS 2016-2019 Parts certificateThe manufacturer's specifications apply for installation. An existing certificate is no guarantee that the product can also be installed in the corresponding vehicle.A certificate is available for this product for the following regions and vehicles:* DE/AT: Vehicle registration document, field K --- CH/LI: Vehicle registration document, field 24Country Model Type approval*DE/AT BMW M2 from e1*xx/xx*0377*09DE/AT BMW M2 Competition from e1*xx/xx*0377*09DE/AT BMW M3 from e1*xx/xx*0377*15DE/AT BMW M3 up to e1*xx/xx*0377*14DE/AT BMW M4 from e1*xx/xx*0377*15DE/AT BMW M4 up to e1*xx/xx*0377*14DE/AT BMW M4 CS e1*KS07/46*0012*..DE/AT BMW M4 GTS e1*KS07/46*0012*..

Elegantly sporty - 3DDesign combines a perfect fit with uncompromising part quality. The best M2C set the market has ever seen. Compatible vehicles:BMW 2 Coupe (F22, F87) M2 CS 2019-2021BMW 2 Coupe (F22, F87) M2 Competition 2018-2021

The 3DDesign carbon diffuser for BMW F87 M2 is made of carbon fiber/carbon fiber and gives the rear of the M2 a new shine in no time at all. Installation is extremely simple - but the effect is all the greater. The calm design of the diffuser emphasizes the elegance of the otherwise sporty vehicle. Incl. parts certificate Compatible vehicles:BMW 2 Coupe (F22, F87) M2 2015-2018BMW 2 Coupe (F22, F87) M2 CS 2019-2021BMW 2 Coupe (F22, F87) M2 Competition 2018-2021

Small but fine extensions that will make your BMW F87 stand out from the crowd. Understatement in detail tuning! Please note that this item is not a rear wing but only the extensions! Compatible vehicles:BMW 2 Coupe (F22, F87) M2 2015-2018BMW 2 Coupe (F22, F87) M2 CS 2019-2021BMW 2 Coupe (F22, F87) M2 Competition 2018-2021

The 3DDesign carbon rear wing for BMW F87 M2 is once again an absolute masterpiece from the Japanese pen of 3DDesign. The wing panel is visually identical to the rear wings of the big brothers F80 M3 and F82 M4. The design is not only visually stunning. The wing is particularly impressive from an aerodynamic point of view, as the downforce on the rear axle is increased enormously. Incl. parts certificate Compatible vehicles:BMW 2 Coupe (F22, F87) M2 2015-2018BMW 2 Coupe (F22, F87) M2 CS 2019-2021BMW 2 Coupe (F22, F87) M2 Competition 2018-2021

The F87/F22's adaptive LED headlights are already aggressive with the angled 3/4-style etched rings, but the vehicle has left room for improvement. The Yellow DRL upgrade gives your car the race-inspired look it deserves. Details:- Complete Yellow DRL LED boards for left and right headlights- Thermally conductive adhesive- Plug-and-play installation (fully reversible)- All OEM functionalities are retained- Complete installation instructions- 2 year warranty- Not approved in the area of the StVZO. Only suitable for use in motorsport. Installation is very simple: the modules can be easily installed in your own garage using plug-and-play and simple tools. The price does not include installation. Compatible vehicles:BMW F87/F22 2 Series LCI LED only (2018-2021)Note: This is NOT an original BMW product!Note: This is NOT an original BMW product!