KW V1 coilover suspension inox | fits Audi A1 (GB), VW Polo (AW) GTI | 102800BW | 102800BY

KW V1 coilover suspension

Sportiness paired with outstanding looks. With factory pre-configured damping.
Our entry-level model for more driving pleasure through an appealing and individually adjustable lowering is the KW V1 coilover suspension in the KW typical "inox-line". Thanks to its high-quality workmanship, the consistent use of stainless steel struts, corrosion-resistant springs and harmonised components, it stands for many years of driving pleasure - and not just for the life of the car.

Stepless lowering
The KW V1 enables maximum lowering within the tested adjustment range. This varies depending on the vehicle model and can, for example, be between 30 and 70 millimetres or 50 to 90 millimetres for an individual lowering. Thanks to the dirt-resistant trapezoidal thread and the polyamide threaded ring, the stepless lowering can be varied quickly and easily even years later. Depending on the vehicle, the lowering is carried out either on the wheel-guiding KW stainless steel suspension struts or on the rear axle height adjustment for non-wheel-guiding double-wishbone rear axles.

The benchmark for sporty, dynamic tuning fans
With its harmonious basic set-up for sporty driving on the road, the KW V1 convinces the discerning tuning fan. Our development engineers determine a specific damper set-up and spring rate for each vehicle in order to enhance your driving pleasure with the optimum balance of sportiness and suitability for everyday use. After all, you are not buying just any coilover suspension, but a KW coilover suspension that has been specially developed and tuned for your vehicle type. As a manufacturer, KW only uses its own resources, high-quality components and the same damper technology as mass-produced manufacturers. With the KW V1, the rolling and rolling movements of the vehicle body are reduced during compression, allowing you to benefit from unadulterated directness and sportier handling when driving.

Our experience for your driving pleasure
For over 25 years, we have been the market leader and innovation driver as a manufacturer of customised suspension solutions for road and racing. No matter where in the world, sporty drivers, car manufacturers and tuners rely on our KW coilovers "Made in Germany". Every KW coilover suspension is subjected to extensive load tests during production and is developed and manufactured directly at our company headquarters in Fichtenberg, Swabia, in order to fulfil the high standards of our KW quality management. As a German manufacturer, it is a matter of course for us to provide a multi-year warranty on our KW coilover suspension kits, which exceed OEM quality and cover over 4,600 applications. When installed by one of our KW specialist dealers, this warranty is valid for up to five years.

- Optimally adjusted in advance
- sporty and harmonious damping technology
- Stainless steel technology "inox-line"
- Individually height-adjustable
- Tested adjustment range
- Ready-to-install complete solution
- High-quality components for a long service life
- Complete documentation for easy handling

Setup - factory pre-configured damping setup
The KW V1 has a vehicle-specific, permanently configured damper setup. The spring and the damper are perfectly matched to each other so that you experience an optimum balance of sportiness and suitability for everyday use when driving.

Even with a full payload and maximum axle loads, the dampers always work with a sporty characteristic curve. The KW V1 is particularly interesting for tuning enthusiasts who prioritise the show & shine concept.

Please note the conditions and instructions for this product:
- VA + HA height-adjustable (VA coilover struts, HA springs with height adjustment + damper)
- For vehicles with electronic damper control, this must be decommissioned. Electronic kit for decommissioning is included in the scope of delivery for article variant "YES".

Technical information:
Lowering VA/HA (mm): 30-50/30-50
Version: V1
Height adjustment: none
Material: Stainless steel
Adjustment VA/HA: thread/thread
Approval: Parts certificate (§19.3)

Compatible vehicles:
Manufacturer Model Version Body Fuel Performance Displacement Cylinder Drive
AUDI A1 Sportback (GB) GBA 07/2018- 25 TFSI hatchback petrol 70 KW 999 ccm 3 front-wheel drive
AUDI A1 Sportback (GB) GBA 07/2018- 30 TFSI hatchback petrol 81 KW 999 ccm 3 front-wheel drive
AUDI A1 Sportback (GB) GBA 07/2018- 30 TFSI hatchback petrol 85 KW 999 ccm 3 front-wheel drive
AUDI A1 Sportback (GB) GBA 07/2018- 35 TFSI hatchback petrol 110 KW 1495 ccm 4 front-wheel drive
AUDI A1 Sportback (GB) GBA 07/2018- 40 TFSI hatchback petrol 147 KW 1984 ccm 4 front-wheel drive
AUDI A1 Sportback (GB) GBA 07/2018- 40 TFSI hatchback petrol 152 KW 1984 cc 4 front-wheel drive
SKODA SCALA (NW) 02/2019- 1.0 TSI Hatchback Petrol 70 KW 999 ccm 3 Front-wheel drive
SKODA SCALA (NW) 02/2019- 1.0 TSI Hatchback Petrol 81 KW 999 ccm 3 Front-wheel drive
SKODA SCALA (NW) 02/2019- 1.0 TSI Hatchback Petrol 85 KW 999 ccm 3 Front-wheel drive
SKODA SCALA (NW) 02/2019- 1.5 TSI Hatchback Petrol 110 KW 1495 ccm 4 Front-wheel drive
SKODA SCALA (NW) 02/2019- 1.6 TDI Hatchback Diesel 70 KW 1598 ccm 4 Front-wheel drive
SKODA SCALA (NW) 02/2019- 1.6 TDI Hatchback Diesel 85 KW 1598 ccm 4 front-wheel drive
VW POLO VI (AW, AW1, BZ1) 06/2017- 2.0 GTI hatchback petrol 147 KW 1984 ccm 4 front-wheel drive
VW POLO VI (AW, AW1, BZ1) 06/2017- GTI hatchback petrol 152 KW 1984 ccm 4 front-wheel drive
Only for vehicles without DCC