Diffusor Carbon | fits BMW M3 incl. CRT (E90) S65 | 3DDesign

In many vehicles, brake cooling is already recommended for medium loads, even off the racetrack.This not only improves braking performance, but can also drastically reduce wear on the friction partners.We use the channeling of the air flow to the center of the brake disc to utilize the turbine effect to cool the disc from the inside. In doing so, we direct the airflow at the disc at a specific angle in order to avoid scattering losses and make maximum efficient use of the available air volume.Thanks to the lightweight construction in combination with powdered aluminum, the component is sufficiently strong and at the same time light and robust. Your vehicle is not slow, that's a fact. However, this speed must be reduced as quickly as possible before cornering and this generates enormous heat. The ball joint of your control arm is extremely close to the hot brake disk and will be affected in the long term. This anchor plate therefore provides additional shielding for the bearing, thereby increasing its durability. Scope of delivery:Anchor plates for the front axle 1x left 1x right with connection for 51 mm air hose(air hose + clamps not included, optionally available). The anchor plate fits plug & play and no additional fastening material is required. The original fixing points and screws can be reused. Suitable for: E90/92/93 M3E82 1 Series M

Facts: - Tailpipes: 4x 80mm black - Material: stainless steel - electric flaps - Made in Germany (Lake Constance) - with/without ECE approval (depending on choice of flap control)* Scope of delivery: - 1x Aulitzky Exhaust rear silencer - 4x tailpipes 80mm black - Additional control unit (ECE) incl. cable set - ECE handout Compatible vehicles: VehicleVehicle typePower outputEngine capacityEngineYear of constructionBMW 3 Series (E90/E92)M3309kW / 420hp3999cm³S65 B40 A06.07 - 06.13 *ATTENTION! In conjunction with the standard or ECE flap control system (with type approval), this flap rear silencer has ECE approval, meaning that it can be used legally within the scope of the StVZO without registration in the vehicle documents.The use of flap rear silencers in conjunction with the race flap control (without approval) is not permitted for use on public roads and is only intended for racing purposes! If you nevertheless install a product without approval in your vehicle and use it within the scope of the StVZO, you are liable to prosecution. Possible consequences that you can expect in this case: Expiry of the operating licence in accordance with §19 of the StVZO and possible resulting immobilisation of the vehicle. Other possible consequences, such as a charge of tax evasion, as well as possible investigations by the environmental authorities are at the discretion of the investigators.

Funktion: - variable Klappensteuerung der originalen oder nachgerüsteten Klappenabgasanlage - über Lenkradtasten steuerbar Kompatible Fahrzeuge:FahrzeugTypLeistungHubraumMotorBaujahr BMW 3er (E90/E92/E93)M3309kW / 420PS3999cm³S65 B40 A06.07 - 06.13 Hinweis: Dieses Produkt ist NICHT in der StVZO zugelassen und NICHT für den Verkauf innerhalb der EU gedacht! Dieser Artikel dient ausschließlich für Show- & Motorsportzwecke und darf nicht im öffentlichen Straßenverkehr genutzt/verbaut werden. Sollte das Bauteil am/im Fahrzeug verbaut sein, erlischt die Betriebserlaubnis!Bei den abgebildeten Bildern handelt es sich um Beispielbilder.

MOVIT DDE steel brake system 370x35mm (6 piston calliper) for the front axle, from 18 inch rims upwardsApplication-focussed development is the cornerstone of this high-performance brake system. The required balance of weight, performance and durability is optimally combined. The uncompromising selection of materials in production results in a highly unique product that meets the diverse requirements of extreme automotive applications. The most important features of the MOVIT brake system are- The progressive staggering of the piston diameters, matched to the vehicle, so that precisely parallel contact pressure between the pad and the disc is guaranteed. This enables even wear of the brake pads and ensures even heat transfer and a reduced system temperature.- Very good heat dissipation due to the open design of the brake pad contour.- Calipers manufactured from high-strength, highly tempered aircraft aluminium 7075 with high-quality material properties (stiffer components, more homogeneous structure), hard anodised and coated with a triple paint finish.- Optimised stability due to the length of the callipers- Larger brake disc diameter and thickness, more cross holes (each pre-cast hole is re-drilled and countersunk, which has a favourable effect on the flow).- The brake discs are thermally tempered.- The optimised DDE ventilation system (double directional evolvent system) of the brake disc has an 80% larger surface area compared to other brake discs, the temperature of the brake disc is significantly reduced and therefore also the wear.- Long service life of the wearing parts, excellent response behaviour, steel flex lines ensure consistent performance.- Optimally matched brake pads ensure fading resistance, a long service life and reduced wear on spare parts Attention: The conversion means that only rims with at least 18 inches can be fitted! The chassis number of the vehicle on which the brakes are fitted is required for the parts certificate. MOVIT sports brake callipers, 6s5, 6-piston- Milled from high-strength aircraft aluminium 7075- Two-piece- Use of maximum disc size due to long design- Significantly improved rigidity and extended contact surface of the pad- Uniform heat transfer- Reduced system temperature- Low, even pad wear- Progressive piston staggering- Crown system for fixing the brake hose- RAPAD-X system for quick brake pad replacement without removing the caliper from the bracket- Open brake pad track for optimised cooling- Maximum stability- Maximum braking force MOVIT sports brake discs, 370x35mm, 2-piece- Highly efficient DDE cooling system- Perforated for optimum response behaviour even on wet roads- Maximum fading resistance- Special alloy for high thermal conductivity MOVIT comfort brake pads, BE-6s1- Enlarged friction surface- Lower system temperature- Uniform heat transfer- Longer service life Scope of delivery:2x MOVIT brake caliper (left/right)2x MOVIT brake disc (left/right)2x vehicle-specific brake caliper adapter1x set of comfort brake pads2x steel flex lines1x assembly material1x installation instructions and running-in instructions1x parts certificate Compatible vehicles:BMW 1 Series F20 / F21 (also M)Ford Focus RS CB4 / MKIIAudi RS3 8PAudi RS4 B5Audi S4 Type 8D / B5BMW M3 E46BMW M3 E46 CSLBMW M3 E92Ford Mustang V Shelby GT 500Mercedes Benz W639 Vito / VianoVolvo XC90 1st gen. from 2011 onwardsVW Golf VII GTI / GTD 57 series pistonsVW Golf VII GTI / GTD 57 series pistonsVW GOLF VII GTI Clubsport / Performance 60 series pistonsVW Golf VII RVW Golf VII RVW T5 / T6 Multivan

MOVIT DDE steel brake system 396x36mm (6 piston calliper) for the front axle, from 20 inch rims upwardsApplication-focussed development is the cornerstone of this high-performance brake system. The required balance of weight, performance and durability is optimally combined. The uncompromising selection of materials in production results in a highly unique product that meets the diverse requirements of extreme automotive applications. The most important features of the MOVIT brake system are- The progressive staggering of the piston diameters, matched to the vehicle, so that precisely parallel contact pressure between the pad and the disc is guaranteed. This enables even wear of the brake pads and ensures even heat transfer and a reduced system temperature.- Very good heat dissipation due to the open design of the brake pad contour.- Calipers manufactured from high-strength, highly tempered aircraft aluminium 7075 with high-quality material properties (stiffer components, more homogeneous structure), hard anodised and coated with a triple paint finish.- Optimised stability due to the length of the callipers- Larger brake disc diameter and thickness, more cross holes (each pre-cast hole is re-drilled and countersunk, which has a favourable effect on the flow).- The brake discs are thermally tempered.- The optimised DDE ventilation system (double directional evolvent system) of the brake disc has an 80% larger surface area compared to other brake discs, the temperature of the brake disc is significantly reduced and therefore also the wear.- Long service life of the wearing parts, excellent response behaviour, steel flex lines ensure consistent performance.- Optimally matched brake pads ensure fading resistance, a long service life and reduced wear on spare parts Attention: The conversion means that only rims with at least 20 inches can be fitted! The chassis number of the vehicle on which the brakes are fitted is required for the parts certificate. MOVIT sports brake callipers, 6s1, 6-piston- Milled from high-strength aircraft aluminium 7075- Two-piece- Use of maximum disc size due to long design- Significantly improved rigidity and extended contact surface of the pad- Uniform heat transfer- Reduced system temperature- Low, even pad wear- Progressive piston staggering- Crown system for fixing the brake hose- RAPAD-X system for quick brake pad replacement without removing the caliper from the bracket- Open brake pad track for optimised cooling- Maximum stability- Maximum braking force MOVIT sports brake discs, 396x36mm, 2-piece- Highly efficient DDE cooling system- Perforated for optimum response behaviour even on wet roads- Maximum fading resistance- Special alloy for high thermal conductivity MOVIT comfort brake pads, BE-6s1- Enlarged friction surface- Lower system temperature- Uniform heat transfer- Longer service life Scope of delivery:2x MOVIT brake caliper (left/right)2x MOVIT brake disc (left/right)2x vehicle-specific brake caliper adapter1x set of comfort brake pads2x steel flex lines1x assembly material1x installation instructions and running-in instructions1x parts certificate Compatible vehicles:Audi R8 type 420 -2018Audi S6 Type 4FBMW M2 F87BMW M3 E92BMW M4 F82BMW X5 E70Ford Mustang VI 2016- 2.3l EcoboostFord Mustang VI 5.0 V8 GT 2015-Mercedes Benz W906 Sprinter 3t & 3.5t

MOVIT DDE steel brake system 342x28mm (4 piston calliper) for the rear axle, from 18 inch rims upwardsApplication-focussed development is the cornerstone of this high-performance brake system. The required balance of weight, performance and durability is optimally combined. The uncompromising selection of materials in production results in a highly unique product that fulfils the diverse requirements of extreme automotive applications. The most important features of the MOVIT brake system are- The progressive staggering of the piston diameters, matched to the vehicle, so that precisely parallel contact pressure between the pad and the disc is guaranteed. This enables even wear of the brake pads and ensures even heat transfer and a reduced system temperature.- Very good heat dissipation due to the open design of the brake pad contour.- Calipers manufactured from high-strength, highly tempered aircraft aluminium 7075 with high-quality material properties (stiffer components, more homogeneous structure), hard anodised and coated with a triple layer of paint.- Optimised stability due to the length of the callipers- Larger brake disc diameter and thickness, more cross holes (each pre-cast hole is re-drilled and countersunk, which has a favourable effect on the flow).- The brake discs are thermally tempered.- The optimised DDE ventilation system (double directional evolvent system) of the brake disc has an 80% larger surface area compared to other brake discs, the temperature of the brake disc is significantly reduced and therefore also the wear.- Long service life of the wearing parts, excellent response behaviour, steel flex lines ensure consistent performance.- Optimally matched brake pads ensure fading resistance, a long service life and reduced wear on spare parts Attention: The conversion means that only rims with at least 18 inches can be fitted! The chassis number of the vehicle on which the brakes are fitted is required for the parts certificate. MOVIT sports brake callipers, 4-piston- Milled from high-strength aircraft aluminium 7075- Two-piece- Use of maximum disc size due to long design- Significantly improved rigidity and extended contact surface of the pad- Uniform heat transfer- Reduced system temperature- Low, even pad wear- Progressive piston staggering- Crown system for fixing the brake hose- RAPAD-X system for quick brake pad replacement without removing the caliper from the bracket- Open brake pad track for optimised cooling- Maximum stability- Maximum braking force MOVIT sports brake discs, 342x28mm, 2-piece- Highly efficient DDE cooling system- Perforated for optimum response behaviour even on wet roads- Maximum fading resistance- Special alloy for high thermal conductivity MOVIT comfort brake pads- Enlarged friction surface- Lower system temperature- Uniform heat transfer- Longer service life Scope of delivery:2x MOVIT brake caliper (left/right)2x MOVIT brake disc (left/right)2x vehicle-specific brake caliper adapter1x set of comfort brake pads2x steel flex lines1x handbrake calliper (depending on selected option)1x assembly material1x installation instructions and running-in instructions1x parts certificate Compatible vehicles:BMW 1 Series (F20/F21) (also M)BMW 3 Series (E90)BMW 3 Series (E46) M3BMW 3 Series (E46) M3 CSLBMW 3 Series (E92) M3

MOVIT DDE steel brake system 380x32mm (4 piston calliper) for the rear axle, from 19 inch rims upwardsApplication-focussed development is the cornerstone of this high-performance brake system. The required balance of weight, performance and durability is optimally combined. The uncompromising selection of materials in production results in a highly unique product that meets the diverse requirements of extreme automotive applications. The most important features of the MOVIT brake system are- The progressive staggering of the piston diameters, matched to the vehicle, so that precisely parallel contact pressure between the pad and the disc is guaranteed. This enables even wear of the brake pads and ensures even heat transfer and a reduced system temperature.- Very good heat dissipation due to the open design of the brake pad contour.- Calipers manufactured from high-strength, highly tempered aircraft aluminium 7075 with high-quality material properties (stiffer components, more homogeneous structure), hard anodised and coated with a triple paint finish.- Optimised stability due to the length of the callipers- Larger brake disc diameter and thickness, more cross holes (each pre-cast hole is re-drilled and countersunk, which has a favourable effect on the flow).- The brake discs are thermally tempered.- The optimised DDE ventilation system (double directional evolvent system) of the brake disc has an 80% larger surface area compared to other brake discs, the temperature of the brake disc is significantly reduced and therefore also the wear.- Long service life of the wearing parts, excellent response behaviour, steel flex lines ensure consistent performance.- Optimally matched brake pads ensure fading resistance, a long service life and reduced wear on spare parts Attention: The conversion means that only rims with at least 19 inches can be fitted! The chassis number of the vehicle on which the brakes are fitted is required for the parts certificate. MOVIT sports brake callipers, 4-piston- Milled from high-strength aircraft aluminium 7075- Two-piece- Use of maximum disc size due to long design- Significantly improved rigidity and extended contact surface of the pad- Uniform heat transfer- Reduced system temperature- Low, even pad wear- Progressive piston staggering- Crown system for fixing the brake hose- RAPAD-X system for quick brake pad replacement without removing the caliper from the bracket- Open brake pad track for optimised cooling- Maximum stability- Maximum braking force MOVIT sports brake discs, 380x32mm, 2-piece- Highly efficient DDE cooling system- Perforated for optimum response behaviour even on wet roads- Highest fading resistance- Special alloy for high thermal conductivity MOVIT comfort brake pads- Enlarged friction surface- Lower system temperature- Uniform heat transfer- Longer service life Scope of delivery:2x MOVIT brake caliper (left/right)2x MOVIT brake disc (left/right)2x vehicle-specific brake caliper adapter1x comfort brake pads2x steel flex lines1x handbrake calliper (depending on selected option)1x installation material1x installation instructions and running-in instructions1x parts certificate Compatible vehicles:BMW 2 Series (F87) Coupé M2 272kW / 370PS / 2979cm³ / N55BMW 3 Series (E92) Coupé M3 309kW / 420PS / 3999cm³ / S65BMW 4 Series (F82) Coupé M4 317kW / 431PS / 2979cm³ / S55

AutoTecknic carbon front bumper canards are the complete solution for aerodynamically tuning the driving behaviour of the front of the vehicle while maintaining its aesthetics. Made from lightweight and durable carbon fibre composites, the canards help to increase the downforce of the front end at high speeds. The additional downforce stabilises the vehicle in sharp corners and increases traction for faster lap times. The properties of the carbon also give the E90, E92 and E93 a more aggressive styling. Note: No drilling is required for installation. Compatible vehicles:BMW 3 (E90) M3 2007-2011BMW 3 (E90) M3 CRT 2011-2011BMW 3 Convertible (E93) M3 2008-2013BMW 3 Coupe (E92) M3 2007-2013BMW 3 Coupe (E92) M3 GTS 2007-2013

Your BMW is missing a data display! We have - the CANchecked display for BMW E90 E91 E92 E93 incl. M3. Also fits the M3 model, of course. Access to all engine data:The sensors are queried directly via Can Bus and are displayed on our tried-and-tested MFD28. The display for the BMW E-series comes with a vehicle-specific cover and fits into the interior like an original part. This means that the ventilation through the slots remains intact. Our display emulates a manufacturer tester so that all detailed values are available. We have optimized the protocol to achieve maximum polling speed. Details:- integrates perfectly into the vehicle interior- Up to 128 sensors can be queried- 10 individually configurable views with our DSS - Display Setup Software- ready-made views for a quick start with our display- simply plug and play via our cable set - plug in, done- 4 additional analog inputs for exhaust gas temperature, oil pressure and more- Best readability - optional anti-reflective film included- Query the sensors like manufacturer diagnostic tools Performance meter:Measure your acceleration times in our performance widget - 0-100, 100-200, 0-200 Data jogging:Log all data to the internal SD card. Whether "on-demand" (start with a tap) or permanently. All data from your last turn is saved. Preset alarms:Preset alarms can be easily activated and customized. For example, receive a large warning message if the exhaust gas temperature is above 900 degrees. 4 additional analog inputs:Additional temperature and/or pressure sensors can be connected for further monitoring options, e.g. exhaust gas temperature or exhaust gas back pressure. An ethanol sensor can be connected to one of the digital inputs. Read out/delete errors:Read out errors from the engine control unit in plain text and also delete them Individual designWhether it's the individual start screen or the selection from a variety of different widgets. Make the display your display! Switch pages with the cruise control button:To make driving safer, we have integrated the cruise control switch here with Lightweight-Performance. When cruise control is not active, you can use the up/down button to switch the views in the display. This has the following advantages:- No "searching" for the display while concentrating on the road ahead- Switching even when wearing gloves (on trackdays)- Quick and safe checking of overview pages and then returning to the main view Here is an example video in the BMW F series. In the E-series, the cruise control lever is separate under the turn signal lever. Driver Dynamics:We have developed a special view for all track drivers who want to further improve their driving style and become a second or two faster:- G-forces (lateral and longitudinal acceleration)- Vehicle speed- Steering angle- accelerator pedal position- Brake pressure This sensor system gives the driver the opportunity to aim for even higher speeds in bends and to hit the braking point even later. Together with the data log in the internal memory, which can be downloaded from the display after a track day, this offers a great opportunity to synchronize the data with a video. Access to all data from the engine control unit:We supply your display with a ready-made TRI file as standard. All sensors that are queried are defined here. Temperatures:Engine water temperature, oil temperature, intake temperature, exhaust temperature, transmission temperature Pressures:Boost pressure, boost pressure target, fuel pressure high pressure pump, exhaust back pressure, low pressure, brake pressure, oil pressure Lambda/mixture:Lambda value target/actual, injection correction, short-term lambda adjustment, total ignition angle Other:RPM, air mass (g/s), vehicle speed, throttle valve angle, battery voltage, gear, accelerator pedal position, longitudinal and lateral acceleration, steering angle, yaw angle, torque, power, boost pressure control valve activation If values are missing, they can easily be added. It always depends on the motor whether it supports the values, sometimes not all sensors are available. Attention: Not all values are available for all engines! For which engines and models is the display for BMW E90 E91 E92 E93 incl. M3:The display panel fits the following BMW 3 Series E models:- N54- N55- S65- Other engines on request The respective version for RHD (right-hand drive) is also available. The data may vary between the different engines. Read out and delete errors:Swipe down to access the "DTC" (Diagnostic Trouble Codes = fault memory). The display reads the fault memory from the engine. Optionally, you can also delete these directly on the display. Errors for the engine are displayed in plain text so that you can decide for yourself whether you can continue driving. MFD28 Technical data:- Dimensions: 70.3 x 52mm - Hardware: 2.8" TFT screen, touchscreen, MicroSD, MicroUSB- High-quality milled aluminum front frame- Symmetrical display - ideal for rotating it by 90- Views completely freely configurable on the PC with our DSS - Display Setup Software- Up to 64 widgets per display- 64 sensors (Can Bus + internal)- 10 views- 4x analog inputs- Optional external switching flash- Can bus switching- Can Bus protocols: UDS, KWP2000, OBD Supported values:Many customers always ask: "Which values can I query from my control unit? The answer: "ALL". Our MFD28 is compatible with ISO 11898-2 and SAE J2284.The control unit manufacturers themselves determine which values are sent via the CAN bus interface. The documentation is important here - possibly even in the form of a DBC file that can be imported directly. You can also access our extensive list of already implemented control units. This can be found in the download area. A total of up to 50 sensors can be queried if the manufacturer supports this.Broadcast data as well as OBD2 queries via Can Bus (11bit/29bit) are implemented. Special protocols such as TP2.0 from VW/Audi and UDS are also available. DSS - Display Setup Software:With our DSS - Display Setup Software, the display can be conveniently configured on the PC. The Can Bus protocol can be customized, you can import DBC files and design the displays with your own widgets.The log viewer downloads log files from the display. These can then be viewed and values can be individually selected and scaled.A built-in Can Bus logger allows you to take a close look at the log. This can be used to reverse-engineer unknown Can Buses.

This high quality front lip will make your vehicle stand out in all the right ways. Get the best of the best with the RKP E9X Clubsport ‘Shorty Style’ carbon fiber front lip. The front lip is made entirely of carbon fiber, making it as tough as it is stunning. It is handcrafted in Germany and has proven itself on the race track as it generates significant downforce. Don't worry about strength, as it is secured with M5 bolts. Compatible vehicles:BMW 3 Convertible (E93) M3 2008-2013BMW 3 Coupe (E92) M3 2007-2013BMW 3 (E90) M3 2007-2013 The article has the following certificate: Material certificate

Includes the following services:- Removing and replacing the connecting rod bearings- Check and measure crankshaft journals- Check and adjust the oil pump- Clean all parts- Wheel alignment- Oil & filter change- incl. all parts such as bearings, screws, seals, oil filter and engine oil (10W60)- Entry in the service booklet with BMW serial number stamp- 1 liter oil refillIn addition, and depending on requirements, we can also replace the spark plugs and engine mounts for an additional charge. Please note:This service can only be carried out at our company headquarters!

The 3DDesign carbon diffuser for the E90 is made entirely of carbon fibre and therefore easily meets all lightweight construction requirements. In addition, the downforce on the rear axle is increased, the aerodynamics improved and the sportiness of the vehicle emphasised. Compatible vehicles:BMW 3 (E90) M3 2007-2011BMW 3 (E90) M3 CRT 2011-2011

The 3DDesign carbon diffuser for the E92 is made entirely of carbon fibre and provides even more sportiness at the rear of the E92. It also increases the downforce on the rear axle, which further improves the aerodynamics of the entire vehicle. Compatible vehicles:BMW 3 Coupe (E92) M3 2007-2013BMW 3 Coupe (E92) M3 GTS 2007-2013

RKP Carbon Diffusor SPORT for the E92/E93 Coupé/Cabrio in GT-Race-Style. Compatible vehicles:BMW 3 Convertible (E93) M3 2008-2013BMW 3 Coupe (E92) M3 2007-2013 The article has a material certificate.Installation: For bolting on.

The Carbon Ducktail is a sporty addition to your E92. Unlike regular carbon fibre, pre-preg carbon is reinforced to increase strength and durability. It can also be a staggering 70% lighter than other carbon fibre options.Prepreg carbon is far more uniform than other carbon types, meaning the likelihood of imperfections is drastically reduced. The manufacturing process eliminates unwanted air bubbles and results in a perfectly smooth and high-gloss finish. Details:- 100% pure prepreg carbon fibre construction- OEM-style weave- High gloss finish- Fit guarantee- Registration according to §21 possible Scope of delivery:- 1x ducktail incl. mounting material Compatible vehicles:BMW E92 M3 Coupé (2008-2013)BMW E92 3 Series Coupé (2006-2013) Note: This is NOT an original BMW product!

Facts:Material: CarbonManufacturer: EventuriParts certificate: A certificate is available for this product for certain regions and vehicles (details below) Introducing our E9X M3 carbon fiber air collector. Made from 100% high quality prepreg carbon including the inner trumpets, this air collector replaces the stock plastic version and unleashes the roar of the naturally aspirated BMW V8 engine.As the trumpet lengths are tuned by BMW to the inner volume, changing this setting can result in a loss of power, so we have kept the same volume so as not to affect the way the car drives in terms of power delivery. Although there is no performance gain from the carbon plenum, the intake noise produced takes the driving experience of the M3 to a whole new level. The raw V8 growl gives the M3 an almost CSL-like sound and is truly an exhilarating experience.We went through several iterations with different material thicknesses to fine tune the sound, and the resulting plenum produces an almost unbelievable intake sound! This plenum can be used with the OEM airbox or any other aftermarket intake system, including our own Eventuri intake systems for a real performance boost. Parts certificateThe manufacturer's specifications apply to installation. An existing certificate is no guarantee that the product can also be installed in the corresponding vehicle. A certificate is available for this product for the following regions and vehicles:* DE/AT: Vehicle registration document, field K --- CH/LI: Vehicle registration document, field 24Country model type approval*DE/AT BMW E90 M3 e1*2007/46*0377*..DE/AT BMW E92 M3 e1*2007/46*0377*..DE/AT BMW E93 M3 e1*2007/46*0377*..DE/AT BMW GTS e1*KS07/46*0012*..DE/AT BMW M3 e1*2001/116*0345*.. Compatible vehicles:VehicleVehicle typePowerEngine capacityEngine typeYear of construction BMW 3er (E90/E92/E93)M3309kW / 420hp3999cm³S65 B40 A06.07 - 06.13

Facts: Material: Carbon Manufacturer: Eventuri Parts certificate: A certificate is available for this product for certain regions and vehicles (details below) Parts certificate The manufacturer's specifications apply for installation. The availability of a certificate is no guarantee that the product can be installed in the corresponding vehicle. A certificate is available for this product for the following regions and vehicles: * DE/AT: Vehicle registration document, field K --- CH/LI: Vehicle licence, field 24 Country model type approval* DE/AT BMW E90 M3 e1*2007/46*0377*.. DE/AT BMW E92 M3 e1*2007/46*0377*.. DE/AT BMW E93 M3 e1*2007/46*0377*.. DE/AT BMW GTS e1*KS07/46*0012*.. DE/AT BMW M3 e1*2001/116*0345*.. CH/LI BMW M3 1BB471 CH/LI BMW M3 1BB570 CH/LI BMW M3 1BB607 CH/LI BMW M3 1BB669 CH/LI BMW M3 1BB955-1BB957 CH/LI BMW M3 1BC611-1BC612 Compatible vehicles: VehicleVehicle typePowerEngine capacityEngine typeYear of constructionBMW 3 Series (E90/E92/E93)M3309kW / 420hp3999cm³S65 B40 A06.07 - 06.13

Facts: Parts certificate: without Material: Carbon Manufacturer: Eventuri A legendary add-on for a legendary car! Our E9X M3 carbon ducts are a direct replacement for the OEM plastic ducts to add the finishing touches to the engine bay. These ducts are made from prepreg carbon and match the rest of our E9X M3 range for the ultimate OEM+ theme. We have also replaced the flexible connector between the ducts and the airbox with an EPDM coupling with our raised V logo. During development we considered adding air scoops to the front duct, but after analysis we realised that there was no performance benefit due to the small opening between the ducts and the airbox, so we decided not to add air scoops. This also leaves the grill openings clear for optimum flow to the radiator. The Eventuri carbon ducts are available in both gloss and matte finishes to match our plenum, intake and airbox lid. Each set consists of: Carbon fibre front duct Carbon fibre rear duct Customised EPDM coupler Compatible vehicles: VehicleVehicle typePowerEngine capacityEngine typeYear of constructionBMW 3 Series (E90/E92/E93)M3309kW / 420hp3999cm³S65 B40 A06.07 - 06.13

Facts:Performance increase: +8-10 hp, +10-12 NmMaterial: CarbonManufacturer: EventuriParts certificate: A certificate is available for this product for certain regions and vehicles (details below) A legendary add-on for a legendary car! Extensive studies of the original, very well developed M3 Intake have paid off in the design of the intake system from Eventuri, because in the end an improvement could still be achieved. The new intake system for the E90, E92 and E93 guarantees a noticeable increase in performance thanks to a frictionless air flow in the new, one-piece intake manifold.In contrast to many other Eventuri intake systems, only the filter, the intake pipe and the intake scoop need to be replaced on the M3. In addition to easier installation, this is reflected above all in the price. The new scoop directs the airflow in such a way that the high pressure can be used without frictional losses due to the position of the air intake directly under the headlights. The resulting significantly cooler and faster airflow leads to a clear optimization of the overall airflow.In repeated tests, these small optimizations allow an increase in performance of between 8 and 10 hp and 10 - 12 Nm more! The intake system for the M3 is included in the scope of delivery:Efficient high flow cone with urethane filterCarbon scoopInlet pipe made of full carbonLaser-cut debris shieldLaser-cut suspension Parts certificateThe manufacturer's specifications apply for installation. An existing certificate is no guarantee that the product can also be installed in the corresponding vehicle. A certificate is available for this product for the following regions and vehicles:* DE/AT: Vehicle registration document, field K --- CH/LI: Vehicle registration document, field 24Country model type approval*DE/AT BMW E90 M3 e1*2007/46*0377*..DE/AT BMW E92 M3 e1*2007/46*0377*..DE/AT BMW E93 M3 e1*2007/46*0377*..DE/AT BMW GTS e1*KS07/46*0012*..DE/AT BMW M3 e1*2001/116*0345*..CH/LI BMW M3 1BB471CH/LI BMW M3 1BB570CH/LI BMW M3 1BB607CH/LI BMW M3 1BB669CH/LI BMW M3 1BB955-1BB957CH/LI BMW M3 1BC611-1BC612 Compatible vehicles:VehicleVehicle typePowerEngine capacityEngine typeYear of construction BMW 3er E90/E92/E93)M3309kW / 420hp3999cm³S65 B40 A06.07 - 06.13

The RKP carbon front diffuser for BMW E9x is the optimum in terms of downforce on the front axle. This front diffuser has a similar effect to the famous Varis System 1 diffuser at the rear. It prevents air turbulence under the car, which has a positive effect on the aerodynamics of the entire vehicle. The front diffuser is also made entirely of carbon fiber, so there is no need to worry about weight. Perfect for the race track! Compatible vehicles:BMW 3 (E90) M3 2007-2011BMW 3 (E90) M3 CRT 2011-2011BMW 3 Convertible (E93) M3 2008-2013BMW 3 Coupe (E92) M3 2007-2013BMW 3 Coupe (E92) M3 GTS 2007-2013

AutoTecknic Carbon Front Grille - E92 Pre-LCI Coupe - Plain Weave Compatible vehicles:BMW    3 Cabriolet (E93)    320 d    2007-2010BMW    3 Cabriolet (E93)    320 d    2008-2010BMW    3 Cabriolet (E93)    320 d    2008-2013BMW    3 Cabriolet (E93)    320 i    2006-2013BMW    3 Cabriolet (E93)    320 i    2007-2013BMW    3 Cabriolet (E93)    320 i    2007-2013BMW    3 Cabriolet (E93)    323 i    2007-2011BMW    3 Cabriolet (E93)    325 d    2007-2010BMW    3 Cabriolet (E93)    325 d    2007-2010BMW    3 Cabriolet (E93)    325 i    2006-2010BMW    3 Cabriolet (E93)    325 i    2006-2013BMW    3 Cabriolet (E93)    325 i    2007-2013BMW    3 Cabriolet (E93)    330 d    2007-2013BMW    3 Cabriolet (E93)    330 i    2007-2010BMW    3 Cabriolet (E93)    330 i    2007-2013BMW    3 Cabriolet (E93)    335 i    2006-2013BMW    3 Cabriolet (E93)    M3    2008-2013BMW    3 Coupe (E92)    316 i   2007-2013BMW    3 Coupe (E92)    320 d    2006-2010BMW    3 Coupe (E92)    320 d    2006-2010BMW    3 Coupe (E92)    320 d    2007-2013BMW    3 Coupe (E92)    320 i    2007-2013BMW    3 Coupe (E92)    320 i    2007-2013BMW    3 Coupe (E92)    320 i    2007-2013BMW    3 Coupe (E92)    323 i    2006-2012BMW    3 Coupe (E92)    325 d    2007-2010BMW    3 Coupe (E92)    325 d    2007-2010BMW    3 Coupe (E92)    325 i    2006-2010BMW    3 Coupe (E92)    325 i    2007-2013BMW    3 Coupe (E92)    325 i    2010-2013BMW    3 Coupe (E92)    325 i xDrive    2008-2013BMW    3 Coupe (E92)    325 i xDrive    2008-2013BMW    3 Coupe (E92)    325 i xDrive    2010-2013BMW    3 Coupe (E92)    325 xi    2006-2010BMW    3 Coupe (E92)    325 xi    2007-2008BMW    3 Coupe (E92)    325 xi    2007-2008BMW    3 Coupe (E92)    328 i    2006-2013BMW    3 Coupe (E92)    330 d    2006-2008BMW    3 Coupe (E92)    330 i    2006-2010BMW    3 Coupe (E92)    330 i    2007-2013BMW    3 Coupe (E92)    330 i xDrive    2010-2013BMW    3 Coupe (E92)    330 xd    2006-2008BMW    3 Coupe (E92)    330 xi    2006-2007BMW    3 Coupe (E92)    330 xi    2006-2007BMW    3 Coupe (E92)    330 xi    2007-2010BMW    3 Coupe (E92)    335 d    2006-2013BMW    3 Coupe (E92)    335 i    2006-2013BMW    3 Coupe (E92)    335 i    2006-2013BMW    3 Coupe (E92)    335 i xDrive    2008-2013BMW    3 Coupe (E92)    335 xi    2007-2010BMW    3 Coupe (E92)    M3    2007-2013BMW    3 Coupe (E92)    M3 GTS    2007-2013

The design of the RKP Carbon Clubsport front lip for E9x is reminiscent of the GT4 lip. The Clubsport lip is made entirely of carbon fibre. It not only provides that certain something visually, the effects on the aerodynamic properties of the vehicle in particular are enormous. On the one hand, the front lip ensures greatly increased downforce on the front axle and the additional brake ventilation also benefits all track tools. The lap times on the Nordschleife are definitely shortened! Compatible vehicles:BMW 3 (E90) M3 2007-2011BMW 3 (E90) M3 CRT 2011-2011BMW 3 Convertible (E93) M3 2008-2013BMW 3 Coupe (E92) M3 2007-2013BMW 3 Coupe (E92) M3 GTS 2007-2013

Do you want the CRT look but can't find a suitable part? Here is our latest product, the CRT inspired front lip for the E9x. This carbon lip is made from 3K twill weave carbon fibre and 100% real vacuum technology for ultimate lightweight, high durability and fitment. Designed to utilise the OEM mounting position for quick and easy installation. AutoTecknic high performance, air-cooled carbon aero splitters are both highly visible and highly functional. Compatible vehicles:BMW 3 (E90) M3 2007-2011BMW 3 (E90) M3 CRT 2011-2011BMW 3 Convertible (E93) M3 2008-2013BMW 3 Coupe (E92) M3 2007-2013BMW 3 Coupe (E92) M3 GTS 2007-2013

This carbon front lip is the OEM front lip shown on the infamous fire orange GTS. The lower lip is attached to the vehicle with aluminium brackets and is adjustable. Compatible vehicles:BMW 3 (E90) M3 2007-2011BMW 3 (E90) M3 CRT 2011-2011BMW 3 Convertible (E93) M3 2008-2013BMW 3 Coupe (E92) M3 2007-2013BMW 3 Coupe (E92) M3 GTS 2007-2013 The article has the following certificate: Material Expertise