Data display 3.2" MFD32 Gen.2 | fits Skoda Octavia (5E) | CANchecked

Your Skoda Octavia is missing a data display! We have - the CANchecked MFD32 Gen.2 for the Skoda Octavia Mk3 (Type 5E 2012-2020).

Access to all data from the vehicle - i.e. ALL (also transmission, speedometer, etc).
The sensors are queried directly via Can Bus and are displayed on our tried-and-tested MFD32. The Skoda Octavia MK3 display comes with a vehicle-specific cover and fits into the interior like an original part. This means that the ventilation remains intact through the slots.

Our display emulates a manufacturer tester so that all detailed values are available. We have optimised the protocol to achieve maximum query speed.

Details:
- integrates perfectly into the vehicle interior
- Up to 64 sensors can be interrogated
- 10 individually configurable views with our DSS - Display Setup Software
- ready-made views for a quick start with our display
- simply plug and play via our cable set - plug in, done
- 4 additional analogue inputs for exhaust gas temperature, oil pressure and more
- Best readability - optional anti-reflective film included
- Query the sensors like manufacturer diagnostic tools

Performance metre:
Measure your acceleration times in our performance widget - 0-100, 100-200, 0-200

Data jogging:
Log all data to the internal SD card. Whether "on-demand" (start with a tap) or permanently. All data from your last turn is saved.

Preset alarms:
Preset alerts can be easily activated and customised. For example, receive a large warning message if the exhaust gas temperature is above 900 degrees.

4 additional analogue inputs:
Additional temperature and/or pressure sensors can be connected for further monitoring options, e.g. exhaust gas temperature or exhaust gas back pressure. An ethanol sensor can be connected to one of the digital inputs.

Read out/delete errors:
Read out errors from the engine control unit in plain text and also delete them

Customised design:
Whether it's the customised start screen or the selection from a variety of different widgets. Make the display your display!

Access to all data from the engine control unit:
We supply your display with a ready-made TRI file as standard. All sensors that are queried are defined here.

Temperatures:
Exhaust temperature, engine water temperature, oil temperature, intake temperature, outside temperature, petrol temperature, gearbox temperature

Pressures:
Boost pressure, ambient pressure, fuel pressure pre-feed pump target/actual, fuel pressure high-pressure pump target/actual

Lambda/mixture:
Lambda value target/actual, injection time, short-term lambda adjustment, long-term lambda adjustment

Other:
RPM, air mass (g/s), vehicle speed, throttle valve angle, total ignition angle, ignition angle reduction per cylinder, N75 acceleration in %, terminal 30 voltage, torque, gear

If values are missing, they can easily be added. It always depends on the engine whether it supports the values, sometimes not all sensors are available.

For which engines and models is the display:
The display panel fits all Skoda Octavia MK3 left-hand drive vehicles. A version for RHD (right-hand drive) is also available.

If you have any questions, please contact us - please always tell us the engine code letter of your vehicle.

Read out and delete errors:
Swipe down to access the "DTC" (Diagnostic Trouble Codes = fault memory). The display reads out the fault memory of the engine, transmission, ABS and, if available, the all-wheel drive system (Haldex). Optionally, you can also delete these directly on the display.

Errors for the engine are displayed in plain text so that you can decide for yourself whether you can continue driving.
Skoda Octavia MK3 display

MFD32 Technical data:
- Dimensions: 89 x 60mm
- Hardware: 3.2" TFT screen, touchscreen, MicroSD, MicroUSB
- Symmetrical display - ideal for rotating it 90°
- Views can be freely configured directly on the display or with our DSS - Display Setup Software on the PC
- Up to 64 widgets per display
- 64 sensors (Can Bus + internal)
- 10 views
- 4x analogue inputs
- 2x speed input
- Optional external switching flash
- Can bus switching

Supported values:
Many customers always ask: "Which values can I query from my control unit? The answer: "ALL". Our MFD32 is compatible with ISO 11898-2 and SAE J2284.
The control unit manufacturers themselves determine which values are sent via the CAN bus interface. The documentation is important here - possibly even in the form of a DBC file that can be imported directly. You can also access our extensive list of already implemented control units. This can be found in the download area. A total of up to 50 sensors can be queried if the manufacturer supports this.
Broadcast data as well as OBD2 queries via Can Bus (11bit/29bit) are implemented. Special protocols such as TP2.0 from VW/Audi and UDS are also available.

DSS - Display Setup Software:
With our DSS - Display Setup Software, the display can be conveniently configured on the PC. The Can Bus protocol can be customised, you can import DBC files and design the displays with your own widgets.
The log viewer downloads log files from the display. These can then be viewed and values can be individually selected and scaled.
An in-built Can Bus logger allows you to take a close look at the log. This can be used to reverse-engineer unknown Can Buses.