Aulitzky Exhaust | ECE exhaust system 3" (76mm) from OPF with flap control | fits BMW M140i/M240i/340i/440i (F-series) | PRE ORDER

Here you get a sports air filter with all its advantages:- higher air flow rate- higher filter performance (even smaller particles are filtered)- The particles are trapped in the filter after intake and thus remain trapped until cleaning.- Washable and reusable filter- Increased air flow and therefore better combustion in the engine- No reduction in air flow over a minimum of 50,000 km- Sufficient air even at high engine speeds- more power- Better intake noise- Reduced fuel consumption These sports air filters have polyurethane as the edge material. Polyurethane is more resistant to petrol, vapours and the like. It has an ideal remoulding. This ensures that the edge of the filter is 100% sealed even when it is reinserted after cleaning. The edge surface is made from a single mould. With many other makes, pores in the edge material and joining surfaces where the edge is joined together often lead to a crack in the edge, which can result in unclean air being sucked into the engine. With paper filters, the air flow rate is significantly lower and decreases further after just a short period of use.In addition, paper filters must be disposed of after the specified mileage. TitanTec sports air filters last a lifetime. This is good for the environment and your wallet.Other washable cotton filters only filter much larger particles compared to TitanTec sports air filters. Cleaning the filters:A TitanTec sports air filter has no oil residue and has 100% of its original performance again after cleaning.Cleaning is quick and easy.We recommend cleaning after 15,000-20,000 kilometres or once a year at the latest.The best time to clean the air filter is around the end of May or beginning of June, i.e. after the pollen count, as this is the time when the air filter is under the most strain.Under no circumstances should aggressive cleaning agents such as petroleum ether, cleaning petrol, brake cleaner etc. be used, as this can damage the material. Details: Type: 2x panel filter Length: 187 mm Width: 235 mm Compatible vehicles: BMW 2 Coupe (G42, G87) M2, 460 hp, 338 kW, from 11/22 BMW 3 (G20, G80, G28) M3, 480 hp, 353 kW, from 11/20 BMW 3 (G20, G80, G28) M3 Competition, 510 hp, 375 kW, from 11/20 BMW 3 (G20, G80, G28) M3 Competition xDrive, 510 hp, 375 kW, from 05/21 BMW 3 (G20, G80, G28) M3 CS xDrive, 551 hp, 405 kW, from 03/23 BMW 3 Touring (G21, G81) M3 Competition xDrive, 510 hp, 375 kW, from 07/22 BMW 4 Coupe (G22, G82) M4, 480 hp, 353 kW, from 11/20 BMW 4 Coupe (G22, G82) M4 Competition, 510 hp, 375 kW, from 11/20 BMW 4 Coupe (G22, G82) M4 Competition M xDrive, 510 hp, 375 kW, from 05/21 BMW 4 Coupe (G22, G82) M4 CSL, 551 hp, 405 kW, 05/22 to 02/23 BMW 4 Convertible (G23, G83) M4 Competition M xDrive, 510 hp, 375 kW, from 07/21

The carbon replacement air intakes Twin Fin for the G8x were developed to match the channel lines of the SP1 G8X front splitter. With both the SP1 and Twin Fin ducts installed, you get the aggressive angles your front end needs.Our covers are a direct replacement, which means you can finally remove the honeycomb grille that is currently in front of the air ducts.These covers are made of pure pre-preg carbon, so the bumper adds minimal weight while providing the aggressive look you've been wanting. Details:- 100% pure pre-preg carbon fiber construction- OEM style fabric- High gloss finish- Fit guarantee- Mounts to the OEM front bumper using the original grille clip positions- with parts certificate according to §19.3 Compatible vehicles:- BMW G80 M3/Competition/CS Sedan (2021+)- BMW G81 M3 Competition Touring (2021+)- BMW G82 M4/Competition/CSL Coupe (2021+)- BMW G83 M4 Competition Convertible (2021+)Note: This is NOT an original BMW product!

Facts: - 2x 3” (76mm), replaces the main catalyst - with 200 cell stainless steel sports catalyst - Euro 6 compatible - for current OPF models - with Thermo-Integral insulation (for an extra charge) - with ECE approval* Compatible vehicles:VehicleVehicle typePowerEngine capacityEngineYear of constructionBMW 2 Series (G87)M2338kW / 460hp353kW / 480hp2993cm³S58 B30 A11.22 -08.24 -BMW 3 Series (G80)M3353kW / 480hp2993cm³S58 B30 B11.20 -BMW 3 Series (G80/G81)M3 Competition / xDrive375kW / 510hp390kW / 530hp2993cm³S58 B30 A05.21 -07.24 -BMW 4 Series (G82)M4353kW / 480hp2993cm³S58 B30 B11.20 -BMW 4 Series (G82/G83)M4 Competition / xDrive375kW / 510hp2993cm³S58 B30 A05.21 - Note: Depending on the software version, the engine control light may light up. We recommend the purchase of an OFF set module or software customisation. *This downpipe has ECE approval so that it can be used within the scope of the German Road Traffic Licensing Regulations (StVZO) without registration in the vehicle documents.

Facts: - Tailpipes: 4x100mm black - 3.0 inch stainless steel - MSD removal - Mounting for the original electric flap actuator - Made in Germany (Lake Constance) - with ECE approval* Scope of delivery: - 1x Aulitzky Exhaust exhaust system from OPF - 4x tailpipes 100mm black - ECE handout Compatible vehicles:VehicleVehicle typePower outputcubic capacityEngineYear of constructionBMW 3 Series (G80)M3353kW / 480PS2993ccS58 B30 B11.20 -BMW 3 Series (G80/G81)M3 Competition / xDrive375kW / 510PS390kW / 530PS2993ccS58 B30 A05.21 -07.24 -BMW 4 Series (G82)M4353kW / 480PS2993ccS58 B30 B11.20 -BMW 4 Series (G82/G83)M4 Competition / M xDrive375kW / 510PS390kW / 530PS2993cm³S58 B30 A05.21 -07.24 - *The ECE and the combination certificate for the pre-facelift and facelift models are available (includes intake, intercooler, boost pipe kit, downpipe, exhaust system, 670hp Aulitzky App performance increase and 107dB increase in stationary noise). In conjunction with the standard flap control system (with type approval), this flap exhaust system has ECE approval, meaning that it can be used legally within the scope of the German Road Traffic Licensing Regulations (StVZO) without registration in the vehicle documents.

Function:- variable flap control of the original or retrofitted flap exhaust system- controllable via steering wheel buttons Compatible vehicles: VehicleTypePowerEngine capacityEngine typeYear of constructionBMW 3er (G80)M3353kW / 480hp2993cm³S58 B30 B11.20 -BMW 3er (G80/G81)M3 Competition / xDrive375kW / 510hp2993cm³S58 B30 A05.21 -BMW 4er (G82)M4353kW / 480hp2993cm³S58 B30 B11.20 -BMW 4er (G82/G83)M4 Competition / M xDrive375kW / 510hp2993cm³S58 B30 A05.21 - Note: This product is NOT StVZO approved and NOT intended for sale within the EU! This item is for show & motorsport purposes only and must not be used/installed on public roads. If the component is installed on/in the vehicle, the operating license expires! The pictures shown are examples.

Suitable for: BMW M2 G87 S58 338kW/460hp 2993cm³ BMW M2 G87 S58 353kW/480hp 2993cm³ BMW M3 G80 S58 353kW/480hp 2993cm³ BMW M3 Competition/xDrive G80/G81 S58 375kW/510hp 2993cm³ BMW M3 Competition xDrive G80/G81 S58 390kW/530hp 2993cm³ BMW M3 CS xDrive G80 S58 405kW/551hp 2993cm³ BMW M4 G82 S58 353kW/480hp 2993cm³ BMW M4 Competition/M xDrive G82/G83 S58 375kW/510hp 2993cm³ BMW M4 CSL xDrive G82 S58 405kW/551hp 2993cm³ BMW M4 CSL xDrive G82 S58 412kW/560PS 2993cm³ Optimise the performance and responsiveness of your G8X with our high-quality Boost Pipe Kit for the S58 engine. Developed using advanced CFD simulations for maximum flow optimisation, this kit offers a premium solution for demanding drivers looking for a performance boost. Your benefits:Flow optimised: Each Boost Pipe has been carefully designed using CFD simulations to ensure optimal airflow and improved performance. Highest pressure resistance: The Boost Pipe Kit has undergone rigorous testing and is pressure resistant up to 6 bar to ensure reliable performance even under extreme conditions. High quality materials: Made from high quality aluminium for maximum durability and performance. Precise fit: Each Boost Pipe is customised for a perfect fit and easy installation without the need for additional adjustments. Improved performance: Optimising the airflow not only increases performance but also improves engine response for an exciting riding experience. Scope of delivery:1x aluminium boost pipe1x parts certificate Note:Please note that the product image is for illustrative purposes only and the actual product may differ. With parts certificate (for easy registration according to §19 paragraph 3 of the StVZO).

Upgrade your G20/G80 with these carbon fibre doors that enhance both style and performance. Details:- Carbon fibre doors, made from high quality prepreg carbon fibre- Guaranteed accuracy of fit, 1:1 from the original- Largely reduced weight, the weight of the carbon fibre doors is less than 1/2 of the original doors.- Price is for 4 doors - front and rear Features:- Lightweight design: made from high quality carbon fibre, these doors are significantly lighter than the stock doors and reduce the overall weight of the vehicle for improved agility and acceleration.- Superior strength: Carbon fibre offers exceptional strength and rigidity, ensuring high durability and resilience while maintaining a slim profile.- Premium finish: The doors feature a high-gloss carbon fibre weave that gives your G20/G80 a refined, race-inspired look and complements its sporty design.- Exact fit: Designed specifically for the G20/G80, these doors offer a precise fit and seamless integration that meets OEM standards for alignment and function.- Improved performance: By reducing weight, these doors contribute to better handling, braking behaviour and improved driving dynamics.- Professional installation recommended: For best results, professional installation is recommended to ensure proper alignment and functionality with your vehicle's systems. Care instructions:Regular cleaning: Maintain carbon fibre parts by cleaning them regularly with a soft cloth and a mixture of mild soap and water. Avoid abrasive cleaners or harsh detergents that could damage the surface.Use microfibre pads and cloths: Use microfibre pads and cloths when cleaning or applying protective coatings to avoid scratching the surface.Protect the product from the sun and chemicals: Avoid direct sunlight and harsh chemicals, as these can damage the carbon fibre. If possible, use protective covers or park your vehicle in shaded areas. Installation:Although the installation of this product is relatively simple for the skilled DIY enthusiast, we still recommend installation by a professional mechanic.No special tools are required to install this product. Scope of delivery:- 4 carbon fibre doors (2x front doors per FS/BFS, 2x rear doors per FS/BFS)- Required mounting parts Compatible vehicles:All G20/G80 modelsNote: This is NOT an original BMW product!

Our high-quality engine cover made from pre-preg carbon fibre is a great addition to enhance the style of your vehicle.The carbon fibre engine cover replaces the standard plastic part. When you buy Pre-Preg carbon fibre, you are investing in a higher quality and more durable material that will outlast other forms of carbon fibre and potentially save you money in the long run. Installation: Plug&Play Details:- 100% carbon fibre construction- High gloss finish- Performance style design- Supplied with 3M double-sided adhesive tape already attached- Use rubber adapter from the original engine cover + emblem- registration free Compatible vehicles with S58 engine:- BMW G87 M2 - BMW G80 M3 Sedan (2021+)- BMW G80 M3 Competition Sedan (2021+)- BMW G81 M3 Touring (2023+)- BMW G81 M3 Competition Touring (2023+)- BMW G82 M4 Coupé (2021+)- BMW G82 M4 Competition Coupé (2021+)- BMW G83 M4 Convertible (2021+)- BMW G83 M4 Competition Convertible (2021+) Note: This is NOT an original BMW product!

The Air Intake Set for the G8X models made of carbon fibre gives your vehicle an upscale look. When you buy Pre-Preg carbon fibre, you are investing in a higher quality and more durable material that will outlast other forms of carbon fibre and potentially save you money in the long run. Scope of delivery:- 1x Air Intake Set Details:- 100% carbon fibre construction- High gloss finish- Fit guarantee Compatible vehicles with S58 engine:- BMW G80 M3 (all models)- BMW G81 M3 (all models)- BMW G82 M4 (all models)- BMW G83 M4 (all models) Note: This is NOT an original BMW product!

The gear knob cover gives your vehicle an upscale look and a pleasant feel. When you buy Pre-Preg carbon fibre, you are investing in a higher quality and more durable material that will outlast other forms of carbon fibre and potentially save you money in the long run.Details:- 100% carbon fibre construction- High gloss finish- Fit guarantee- registration free Compatible vehicles:- BMW G87 M2 - BMW G80 M3 incl. Competition Saloon (2021+)- BMW G81 M3 incl. Competition Touring (2023+)- BMW G82 M4 incl. Competition Coupé (2021+)- BMW G83 M4 incl. Competition Convertible (2021+) Note: This is NOT an original BMW product!

Facts:Power increase: 13-18hp, 12-16ft-lb (stock tune)Turbo inlet area increased by up to 160Filtration area increased by up to 40%Material: CarbonManufacturer: EventuriParts certificate: A certificate is available for this product for certain regions and vehicles (details below) SPECIAL PRICE - used test product from our project vehicle, scratches possible. No warranty. (see pictures) We present an intake system that really sets new standards for the G8X platform. We have carried out intensive research and development work to create an intake system that not only outperforms the standard vehicle, but is also future-proof as it is suitable for power increases of well over 1000 bhp. Our system is a complete redesign from the airboxes to the turbo inlets with the aim of reducing pressure loss while increasing flow rate and keeping inlet temperatures low. We have maximised the use of available space and used 2 custom made filters with a 40% larger filter area than stock. These are used in our patented Venturi housings to direct the air evenly to the turbo inlets. The inlets themselves have a cross section up to 160% larger than standard and are fitted with an advanced dimpled inner surface to reduce frictional losses between the flow and the wall boundary. By creating an air "cushion" on the wall surface, the airflow can move through the inlets at higher flow rates and lower pressure drop. This allows the turbos to draw in air with less resistance, reducing the wastegate duty cycle, resulting in higher overall performance. Bench test This intake system was independently bench tested by BR Performance in Belgium. The tests were carried out back to back with the standard airbox and several runs were made with each configuration. The tested vehicle was driven without an activated carbon filter. We compared the best results with the standard airbox and the best results with the Eventuri system. The results on the test bench show a constant increase over the entire rev range, which is due to the fact that the turbos reach maximum boost pressure earlier and have a lower wastegate duty cycle due to the higher efficiency of the intake system. This increase is despite the increase in dyno temperatures from 11.8 degrees Celsius in the tests with the standard system to almost 16 degrees Celsius in the Eventuri tests. The increase in performance is reflected on the road in improved response at part and full throttle, with the car pulling much more eagerly to the red line. Intake air temperature tests On turbocharged vehicles, a lot of heat can build up in the engine bay, which can have a detrimental effect on performance if the intake system is not sealed against this heat. Even with intercoolers and charge air coolers, it is important to minimise intake air temperatures as these cooling devices operate at a certain efficiency, so the output air temperature is affected by the input air temperature. Restricting the intake tract with open cones, even if they are heat protected, will inevitably draw hot air from the engine bay. Our system, which is fully sealed, solves this problem while still not restricting the flow path by using larger volumes. To demonstrate this, we recorded the air temperatures with thermocouples immediately before each turbo. The comparisons were made on the same day and under the same environmental conditions between the original and Eventuri. Our vehicle was allowed to warm up and then accelerated from 30mph to 90mph in 6th gear to measure the temperature change on each run. The car was then accelerated in 6th gear to measure the temperature change with each run. At 90mph, the accelerator was released and the brakes applied to 30mph, after which the car was accelerated back to 90mph. A total of 3 pull-throughs were performed with both intake configurations. Scope of delivery: - 2x patented carbon fibre Venturi filter housings - 2x Bespoke high flow dry cone filters - 2x carbon intake pipes - 1x carbon intake pipe - 2 thermoplastic turbo inlets - Laser cut stainless steel brackets - Customised flexible hose - CNC machined brackets and reinforcement rings For this product a certificate is available for the following regions and vehicles:* DE/AT: Vehicle registration document, field K --- CH/LI: Vehicle licence, field 24Country Model Type approval*DE/AT BMW M2 e1*2018/858*00211*..DE/AT BMW M3 e1*2018/858*00003*..DE/AT BMW M3 Competition e1*2018/858*00003*..DE/AT BMW M3 Competition M xDrive e1*2018/858*00003*..DE/AT BMW M3 CS e1*KS18/858*00008*..DE/AT BMW M4 e1*2018/858*00003*..DE/AT BMW M4 Competition e1*2018/858*00003*..DE/AT BMW M4 Competition M xDrive e1*2018/858*00003*..DE/AT BMW M4 CSL e1*KS18/858*00008*..CH/LI BMW G234M WBS31AYCH/LI BMW G234M WBS31AZCH/LI BMW G234M WBS31BACH/LI BMW G234M WBS41AYCH/LI BMW G234M WBS41AZCH/LI BMW G234M WBS51AYCH/LI BMW G234M WBS51AZCH/LI BMW G34MKS WBS61AYCH/LI BMW G34MKS WBS61AZCH/LI BMW G34MKS WBS81AZCH/LI BMW M2 WBS11DMCH/LI BMW M3 / G234M WBS11GB Compatible vehicles:VehicleVehicle typePower outputDisplacementEngineYear of construction BMW 2 Series (G87)M2338kW / 460PS353kW / 480PS2993ccS58 B30 B11.20 - BMW 3 Series (G80)M3353kW / 480PS2993cm³S58 B30 B11.20 - BMW 3 Series (G80/G81)M3 Competition / xDrive375kW / 510PS390kW / 530PS2993ccS58 B30 A05.21 - BMW 3 Series (G80)M3 CS xDrive405kW / 551hp2993cm³S58 B30 A05.21 - BMW 4 Series (G82)M4353kW / 480PS2993cm³S58 B30 B11.20 - BMW 4 Series (G82/G83)M4 Competition / M xDrive375kW / 510PS2993cm³S58 B30 A05.21 - BMW 4 Series (G82/G83)M4 CSL xDrive405kW / 551hp412kW / 560PS2993cm³S58 B30 A05.21 -

Transform the engine bay of your G8X with the pre-impregnated carbon replacement radiator shroud. Made from lightweight pre-preg carbon fibre. When you buy pre-preg carbon fibre, you are investing in a higher quality and more durable material that will outlast other forms of carbon fibre and potentially save you money in the long run. Assembly: Plug&Play Details:- 100% carbon fibre construction- High gloss finish- Performance style design- Supplied with 3M double-sided adhesive tape already attached- Use rubber adapter from the original engine cover + emblem- registration free Compatible vehicles with S58 engine:- BMW G87 M2 - BMW G80 M3 Sedan (2021+)- BMW G80 M3 Competition Sedan (2021+)- BMW G81 M3 Touring (2023+)- BMW G81 M3 Competition Touring (2023+)- BMW G82 M4 Coupé (2021+)- BMW G82 M4 Competition Coupé (2021+)- BMW G83 M4 Convertible (2021+)- BMW G83 M4 Competition Convertible (2021+) Note: This is NOT an original BMW product!

Made from state-of-the-art pre-preg carbon fibre, these direct replacement side emblems enhance the aggressive character of your vehicle and make it stand out both on the road and online. Why do we use pre-preg carbon fibre?Unlike regular carbon fibre, pre-preg carbon is reinforced to increase strength and durability.It can also be a staggering 70% lighter than other carbon fibre options, ideal for weight saving.In terms of quality, pre-preg carbon is far more consistent, meaning the likelihood of imperfections is drastically reduced.of imperfections is drastically reduced.The manufacturing process eliminates unwanted air bubbles and results in a perfect, smooth, sleekand high-gloss finish that is the ultimate piece to complement your vehicle. When you buy Pre-Preg, you are investing in a higher quality, more durable part that will outlast other forms ofoutlast other forms of carbon fibre and potentially save you money in the long run. Details:- 100% pure prepreg carbon fibre construction- OEM style weave- High gloss finish- registration free Compatible vehicles:- BMW G80 M3 Sedan (2021+)- BMW G81 M3 Touring (2021+)Note: This is NOT an original BMW product!

Made from state-of-the-art pre-preg carbon fibre, these direct replacement side emblems enhance the aggressive character of your vehicle and make it stand out both on the road and online. Why do we use pre-preg carbon fibre?Unlike regular carbon fibre, pre-preg carbon is reinforced to increase strength and durability.It can also be a staggering 70% lighter than other carbon fibre options, ideal for weight saving.In terms of quality, pre-preg carbon is far more consistent, meaning that the likelihood of imperfections is drastically reduced.of imperfections is drastically reduced.The manufacturing process eliminates unwanted air bubbles and results in a perfect, smooth, sleekand high-gloss finish that is the ultimate piece to complement your vehicle. When you buy Pre-Preg, you are investing in a higher quality, more durable part that will outlast other forms ofoutlast other forms of carbon fibre and potentially save you money in the long run. Details:- 100% pure prepreg carbon fibre construction- OEM style weave- High gloss finish- registration free Compatible vehicles:- BMW G82 M4 Coupe (2021+)- BMW G83 M4 Convertible (2021+)Note: This is NOT an original BMW product!

Made from state-of-the-art pre-preg carbon fibre, these side diffusers for the rear emphasise the character of your vehicle and make it stand out both on the road and online. Why do we use pre-preg carbon fibre?Unlike normal carbon fibre, pre-preg carbon is reinforced to increase strength and durability.It can also be a staggering 70% lighter than other carbon fibre options, ideal for weight saving.In terms of quality, pre-preg carbon is far more consistent, meaning that the likelihood of imperfections is drastically reduced.of imperfections is drastically reduced.The manufacturing process eliminates unwanted air bubbles and results in a perfect, smooth, sleekand high-gloss finish that is the ultimate piece to complement your vehicle. When you buy Pre-Preg, you are investing in a higher quality, more durable part that will outlast other forms ofoutlast other forms of carbon fibre and potentially save you money in the long run. Details:- 100% pure prepreg carbon fibre construction- OEM style weave- High-gloss finish- with parts certificate according to §19.3 Scope of delivery:1x set of side diffusers Compatible vehicles:- BMW G80 M3 Sedan (2021+)- BMW G80 M3 Competition Sedan (2021+)- BMW G81 M3 Competition Touring (2021+)Note: This is NOT an original BMW product!

Made from state-of-the-art pre-preg carbon fibre, these side skirts emphasise the character of your vehicle and make it stand out both on the road and online. Why do we use pre-preg carbon fibre?Unlike normal carbon fibre, pre-preg carbon is reinforced to increase strength and durability.It can also be a staggering 70% lighter than other carbon fibre options, ideal for weight saving.In terms of quality, pre-preg carbon is far more consistent, meaning that the likelihood of imperfections is drastically reduced.of imperfections is drastically reduced.The manufacturing process eliminates unwanted air bubbles and results in a perfect, smooth, sleekand high-gloss finish that is the ultimate piece to complement your vehicle. When you buy Pre-Preg, you are investing in a higher quality, more durable part that will outlast other forms ofoutlast other forms of carbon fibre and potentially save you money in the long run. Details:- 100% pure prepreg carbon fibre construction- OEM style weave- High-gloss finish- with parts certificate according to §19.3 Scope of delivery:1x set of side skirts Compatible vehicles:- BMW G80 M3 Sedan (2021+)- BMW G81 M3 Touring (2021+)Note: This is NOT an original BMW product!

Made from prepreg carbon fibre, these side skirts emphasise the character of your vehicle and make it stand out both on the road and on the internet. Why do we use pre-preg carbon fibre?Unlike normal carbon fibre, pre-preg carbon is reinforced to increase strength and durability.It can also be a staggering 70% lighter than other carbon fibre options, ideal for weight saving.In terms of quality, pre-preg carbon is far more consistent, meaning that the likelihood of imperfections is drastically reduced.of imperfections is drastically reduced.The manufacturing process eliminates unwanted air bubbles and results in a perfect, smooth, sleekand high-gloss finish that is the ultimate piece to complement your vehicle. When you buy Pre-Preg, you are investing in a higher quality, more durable part that will outlast other forms ofoutlast other forms of carbon fibre and potentially save you money in the long run. Details:- 100% pure prepreg carbon fibre construction- OEM style weave- High-gloss finish- with parts certificate according to §19.3 Scope of delivery:1x set of side skirts Compatible vehicles:- BMW G82 M4 Coupe (2021+)- BMW G82 M4 Competition Coupe (2021+)Note: This is NOT an original BMW product!

The carbon fibre strut brace in matt or gloss finish gives the engine compartment of your vehicle a sophisticated touch.Details:- Perfect fit and easy installation- More stability- Weight: 1.8 kg- CNC milled connections made from 6061 aluminium- Exclusive and numbered piece- UV protective coating in high gloss or matt depending on selection Compatible vehicles:- BMW G87 M2 models- BMW G80 M3 Sedan models- BMW G81 M3 Touring models- BMW G82 M4 Coupé models- BMW G83 M4 Convertible models Notes:If we do not expressly mention a parts certificate or a general operating licence (ABE) in the product text, it is a motorsport article that is not approved for road traffic according to the German Road Traffic Licensing Regulations (StVZO) and therefore invalidates the operating licence if it is not registered according to § 21 StVZO! Please note that vehicle spare parts should only be installed by a qualified specialist workshop in order to ensure that they function properly and that the vehicle is roadworthy. Note: This is NOT an original BMW product!

The factory front strut brace on the G8x has been completely redesigned and replaced with a pressure-kettle cured, 100% prepreg carbon fibre tube system, reducing the number of joints and potential weak points. Unlike most other G8x dome struts on the market, the unique one-piece V-brace does not use weaker multi-piece joints or off-the-shelf carbon fibre tubes inserted into the body mounts.In addition to increasing rigidity, this strut brace is lighter than the original part. The strut brace is complemented by a CNC machined 6061 aluminium bracket that is integrated directly into the brace itself for added strength. The aluminium bracket is available in a choice of natural silver or black anodised finish. Installation is quick and easy using the factory brackets. You won't regret adding this carbon fibre addition to the engine bay of your G8X, especially if you want to add a carbon fibre intake tract or engine cover! Details:- 2x2 twill weave; high gloss finish- Available finishes for the front aluminium bracket silver or black anodised- One-piece V-brace for maximum strength and rigidity- Mounting with factory parts Compatible vehicles:- BMW G87 M2 models- BMW G80 M3 Saloon models- BMW G81 M3 Touring models- BMW G82 M4 Coupé models- BMW G83 M4 Convertible models Notes:If we do not expressly mention a parts certificate or a general operating licence (ABE) in the product text, it is a motorsport article that is not approved for road use according to the German Road Traffic Licensing Regulations (StVZO) and therefore invalidates the operating licence if it is not registered according to § 21 StVZO! Please note that vehicle spare parts should only be installed by a qualified specialist workshop in order to ensure that they function properly and that the vehicle is roadworthy. Note: This is NOT an original BMW product!

The side centre consoles give your vehicle an upscale look and feel. When you buy Pre-Preg carbon fibre, you are investing in a higher quality and more durable material that will outlast other forms of carbon fibre and potentially save you money in the long run. Details:- 100% carbon fibre construction- High gloss finish- Fit guarantee- registration free Scope of delivery:1x set of centre console side covers (1x right / 1x left) Compatible vehicles:- BMW G87 M2 - BMW G80 M3 incl. Competition Saloon (2021+)- BMW G81 M3 incl. Competition Touring (2023+)- BMW G82 M4 incl. Competition Coupé (2021+)- BMW G83 M4 incl. Competition Convertible (2021+) Note: This is NOT an original BMW product!

The used "Clubsport bar V3" from Bavarian Car Tuning is a high-quality roll bar that was specially developed for the G80/G82. The bar is made of robust and lightweight material that guarantees high strength and rigidity. It is painted in red and blends seamlessly into the interior of your vehicle. The Clubsport bar V3 is easy to install, fits the dimensions of the G80 perfectly and includes an Isofix mount. The rear seat does not need to be removed. The bar can be installed and removed within 10 minutes.With expert opinion Please note that this is a used item, so there may be slight signs of use (see pictures). Nevertheless, it offers a great opportunity to give your vehicle a sporty touch and increase safety at the same time. SPECIAL PRICE - USED (TOP CONDITION)

Transform your G8X into a high-performance powerhouse with the BlackBoost cooling air intake system. Experience more power, style and driving dynamics with this premium upgrade. In the world of performance modifications, the airbox is one of the most important engine components you should upgrade. The factory airbox is very restrictive in terms of airflow and filter area. Our cooling air intakes are designed and engineered to overcome these factory restrictions and deliver the maximum airflow with the lowest possible temperatures given the space available. The BlackBoost Cold Air Intakes are designed to be flush with the bonnet of the vehicle and ensure a consistent seal with the rubber seals of the airbox, whilst also ensuring a large surface area to work properly. The BlackBoost twin-flow filters are specifically designed to maximise airflow and surface area. The BlackBoost intake kit is a plug-and-play solution that works perfectly without further customisation and requires no additional software tuning. It also works smoothly in combination with turbo upgrades, downpipes, methanol injections etc. to unleash the necessary airflow and utilise the full capacity of the engine for those aiming for 1000+ WHP figures. Scope of delivery:- Powder coated airbox- Filters- BlackBoost CFD developed filter adapter- Personalised logo plate Key Features:- Proven power increase from 8 to 30+ hp on production vehicles- Improved responsiveness across the entire rev range- Optimised airflow and increased volume range compared to standard equipment- Increased surface area of the filter elements- Can support airflow for 1000+ WHP configurations- Larger filter element surface area compared to OEM- Plug-and-play bolt-on installation- No ECU tuning required Compatible vehicles:BMW M2 (G87) 338kW | 460PS | 2993cm³ | S58BMW M2 (G87) 353kW | 480PS | 2993cm³ | S58BMW M3 (G80) 353kW | 480PS | 2993cm³ | S58BMW M3 (G80) Competition 375kW | 510PS | 2993cm³ | S58BMW M3 (G80) Competition 375kW | 510PS | 2993cm³ | S58 | xDriveBMW M3 (G80) Competition 390kW | 530PS | 2993cm³ | S58 | xDriveBMW M3 (G80) CS 405kW | 551PS | 2993cm³ | S58 | xDriveBMW M3 (G81) Competition 375kW | 510PS | 2993cm³ | S58 | xDriveBMW M3 (G81) Competition 390kW | 530PS | 2993cm³ | S58 | xDriveBMW M4 (G82) | 353kW | 480PS | 2993cm³ | S58BMW M4 (G82) Competition | 375kW | 510PS | 2993cm³ | S58BMW M4 (G82) Competition M | 375kW | 510PS | 2993cm³ | S58 | xDriveBMW M4 (G82) CSL | 405kW | 551PS | 2993cm³ | S58 | xDriveBMW M4 (G82) CSL | 412kW | 560PS | 2993cm³ | S58 | xDriveBMW M4 (G83) Competition M | 375kW | 510PS | 2993cm³ | S58 | xDrive

Plug and Play suitable for the following models: BMW G80/81 M3 (Competition) 353-375KW/480-510PS from 2021+ BMW G82/G83 M4 (Competition/CSL) 353-405KW/480-550PS from 2021+ Note: only for vehicles with automatic transmission! Now with parts certificate!Optimise the performance and reliability of your S58 with the Wagner Tuning Competition transmission oil cooler kit. This essential kit for all racing enthusiasts offers superior cooling performance and ensures that the oil temperature always remains in the optimum range, even under extreme conditions. Features:Extended cooling surface: The frontal airflow area has been increased by an impressive 81.6%, allowing for significantly more efficient cooling.Larger mesh volume: With a 93.6% larger mesh volume, this transmission oil cooler ensures maximum heat dissipation and keeps the oil temperature stable even under high loads.Optimum performance: Specially developed for performance-enhanced vehicles, this kit guarantees constant and optimum oil cooling to keep the oil pressure stable and extend the service life of the transmission.Easy installation: The plug & play design enables quick and easy installation, so you can have your vehicle up and running in no time at all. Scope of delivery:1x oil cooler (black coated)1x mounting material1x parts certificate Experience the perfect balance between performance and reliability:The Wagner Tuning Competition transmission oil cooler kit is the ideal addition for your S58. Enjoy the benefits of improved cooling and stable performance that impresses even under the most demanding conditions. With parts certificate (for easy registration according to §19 paragraph 3 of the StVZO).

Here we present our display for the M models of the G series. Access to all data from the engine control unit:So ALL. The sensors are queried directly via Can Bus and are displayed on our tried-and-tested MFD32. The display for the G-series comes with a vehicle-specific panel and fits into the interior like an original part. The sensors are queried via the manufacturer-specific Can Bus protocol. We have optimised the protocol to achieve maximum polling speed. Details:- Integrates perfectly into the vehicle interior- Up to 128 sensors can be interrogated- 10 individually configurable views with our DSS - Display Setup Software- ready-made views for a quick start with our display- simply plug and play via our cable set - plug in, done- 4 additional analogue inputs for exhaust gas temperature, oil pressure and more- Ethanol sensor connection directly to the display- Best readability - optional anti-reflective film included- Query the sensors like manufacturer diagnostic tools Performance metre:Measure your acceleration times in our performance widget - 0-100, 100-200, 0-200 Data jogging:Log all data to the internal SD card. Whether "on-demand" (start with a tap) or permanently. All data from your last turn is saved. Preset alarms:Preset alerts can be easily activated and customised. For example, receive a large warning message if the exhaust gas temperature is above 900 degrees. 4 additional analogue inputs:Additional temperature and/or pressure sensors can be connected for further monitoring options, e.g. exhaust gas temperature or exhaust gas back pressure. An ethanol sensor can be connected to one of the digital inputs. Read out/delete errors:Read out errors from the engine control unit in plain text and also delete them Customised designWhether it's the customised start screen or the selection from a variety of different widgets. Make the display your display! Access to all data from the engine control unit:We supply your display with a ready-made TRI file as standard. All sensors that are queried are defined here. Temperatures:Engine water temperature, intake temperature, exhaust temperature, transmission temperature Pressures:Boost pressure, ambient pressure, oil pressure Lambda/mixture:Lambda value target/actual, short-term lambda adjustment, long-term lambda adjustment, MAF, engine load, torque Driver dynamics:Brake pressure, vehicle speed, throttle angle/gas pedal position Other:Engine speed, total ignition angle, gear, battery voltage, ignition angle reduction per cylinder Analogue inputs:Additional sensors can be added here: Oil temperature, petrol pressure, oil pressure, exhaust gas temperature, etc. but also an ethanol sensor (Flex Fuel) If values are missing, they can easily be added. ATTENTION: not every engine offers all values! For which engines and models is the G-series display:The display bezel fits all G-series (G80/G81/G83/G87) left-hand drive (LHD) vehicles that have the ID7 display installed. The pre-assembled bezel does not fit vehicles with the ID8 monitor! A version for right-hand drive vehicles (RHD) is also available. We currently support the following engines, unlisted engines can be added on request:- B48, B57, B58, M54, M57, N13, N20, N47, N52, N54, N55, N57, S55, S58, S63 MFD32 Technical data:- Dimensions: 89 x 60mm - Hardware: 3.2" TFT screen, touchscreen, MicroSD, MicroUSB- Symmetrical display - ideal for rotating it by 90- Views can be freely configured directly on the display or with our DSS - Display Setup Software on the PC- Up to 64 widgets per display- 64 sensors (Can Bus + internal)- 10 views- 4x analogue inputs- 2x speed input- Optional external switching flash- Can bus switching Supported values:Many customers always ask: "Which values can I query from my control unit? The answer: "ALL". Our MFD32 is compatible with ISO 11898-2 and SAE J2284.The control unit manufacturers themselves determine which values are sent via the CAN bus interface. The documentation is important here - possibly even in the form of a DBC file that can be imported directly. You can also access our extensive list of already implemented control units. This can be found in the download area. A total of up to 50 sensors can be queried if the manufacturer supports this.Broadcast data as well as OBD2 queries via Can Bus (11bit/29bit) are implemented. Special protocols such as TP2.0 from VW/Audi and UDS are also available. DSS - Display Setup Software:With our DSS - Display Setup Software, the display can be conveniently configured on the PC. The Can Bus protocol can be customised, you can import DBC files and design the displays with your own widgets.The log viewer downloads log files from the display. These can then be viewed and values can be individually selected and scaled.An in-built Can Bus logger allows you to take a close look at the log. This can be used to reverse-engineer unknown Can Buses.